Leaflet
Transition Networks, Inc.
Worldwide Headquarters:
10900 Red Circle Drive
Minnetonka, MN 55343 USA
tel: 952.941.7600 / 800.526.9267
fax: 952.941.2322
info@transition.com
http://www.transition.com
©2009 Transition Networks, Inc.
All trade marks are the property of their respective owners.
Technical information is subject to change without notice.
AUTO NEG
AUTO CROSS
LINK PASS THR
U
FAR END FAULT
LINK RESTORE
AUTO
PAUSE
REMOTE MGMT
LOOP BACK
ALLOCATION
BANDWIDTH
Specifications
Standards IEEE Std. 802.3
3-position Jumper Jumper J2: Enable/disable AutoCross™
Jumper J6:
Hardware: Device mode determined by 4-position switch
settings
Software: Device mode determined by most recently
saved on-board microprocessor settings.
4 position Switch
Pos 1 Enable/disable twisted pair auto-negotiation
Pos 2 Enable/disable twisted pair pause
Pos 3 (UP) Enables Link Pass Through.
(DOWN) Disables Link Pass Through
Pos 4 (UP) Enables Far-End-Fault
(DOWN) Disables Far-End-Fault.
Status LEDs Power
LKF (Fiber Link)
RXF (Fiber Receive)
RXC (Copper Receive)
LKC (Copper Link)
Dimensions Width: 3.25" [83 mm]
Depth: 4.8" [122 mm]
Height: 1.0" [25 mm]
Power Consumption 4 watts
Power External AC/DC required; 12V DC 0.5A; unregulated;
standard
Environment 0 – 50° C; 5% – 95% humidity non-condensing; 0 –
10,000 feet altitude
Shipping Weight 2 lbs. [0.90 kg]
Safety Compliance Wall Mount Power Supply:
UL Listed and CSA certified
Regulatory Compliance CISPR/EN55022 Class A & B + EN55024; FCC Class A
& B; CE Mark
Warranty Lifetime
Ordering Info
SRMFE1011-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1300nm multimode (ST)
[2 km/ 1.2 mi.] Link Budget: 11.0 dB
SRMFE1013-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1300nm multimode (SC)
[2 km/ 1.2 mi.] Link Budget: 11.0 dB
SRMFE1014-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1310nm SM (SC)
[20 km/12.4 mi.] Link Budget: 16.0 dB
SRMFE1015-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1310nm SM (SC)
[40 km/24.9 mi.] Link Budget: 26.0 dB
SRMFE1016-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1310nm SM (SC)
[60 km/37.3 mi.] Link Budget: 29.0 dB
SRMFE1017-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1550nm SM (SC)
[80 km/49.7 mi.] Link Budget: 29.0 dB
Single Fiber Products
Recommended use in pairs
SRMFE1029-200
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1310nm TX / 1550nm RX sin-
gle fiber single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SRMFE1029-201
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1550nm TX / 1310nm RX sin-
gle fiber single mode (SC)
[20 km/12.4 mi.] Link Budget: 19.0 dB
SRMFE1029-202
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1310nm TX / 1550nm RX sin-
gle fiber single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
SRMFE1029-203
100BASE-TX (RJ-45) [100 m/328 ft.]
to 100BASE-FX 1550nm TX / 1310nm RX sin-
gle fiber single mode (SC)
[40 km/24.9 mi.] Link Budget: 25.0 dB
Optional Accessories
(sold separately)
Wide Input (18 – 72VDC) Power Supplies:
SPS-1872-PS or SPS-1872-SA
Mounting Options:
E-MCR-05
12-slot Media Converter Rack
WMBD or WMBL
Wall Mount Brackets
RMS19-SA4-01
4-slot Media Converter Shelf
Remotely Managed Fast Ethernet
SRMFE10xx-20x
stand-alone network interface device
100BASE-TX to 100BASE-FX
Remotely Managed Fast Ethernet NID
(Network Interface Device)
Features
Auto-Negotiation
AutoCross™
Link Pass Through
Far-End-Fault (FEF)
Automatic Link Restoration
Pause
Loopback
Remote Management
Jumbo Frame Support
In-band management of stand alone Fast
Ethernet NID
Remote Loopback assists in diagnosing
network problems
Upstream and downstream Bandwidth Control
allows service providers to offer an array
of services
With the Remotely Managed Fast Ethernet NID, service providers can now
monitor and manage the entire optical link from the Central Office (CO) to
the Customer Premise Equipment (CPE).
When used in conjunction with a managed Point System™ Chassis card,
(CRMFE), this stand-alone unit can be managed remotely. This Fast Eth-
ernet NID provides a fully-managed conversion between 100BASE-TX and
100BASE-FX signals at Customer Premises.
Devices should be used in pairs. Typical installation will include a chas-
sis card installed in the Point System™ locally and a stand-alone device
(SRMFE) installed at the remote location.