Installation Guide
2
www.transolid.com 800-766-2452 TRANSOLID
®
IMPORTANT NOTICE
IMPORTANT NOTICE: Indicates that equipment or property
damage can result if instructions are not followed.
Read and Understand the Manual
It is the responsibility of any individual who installs or maintains
this product to fully understand and follow proper installation and
maintenance procedures. Be aware of the inherent dangers in
the use of power tools when installing this product. read and un-
derstand all Warnings, Cautions, and Important Notices in this
manual.
Work Safely
DO NOT proceed if any doubt arises about the correct or safe
method of performing anything found in this or other Transolid
®
manuals. The installation of this product can require using power
tools. Do not use power tools without adequate training. If neces-
sary, hire or consult a trained professional for expert assistance
before continuing.
Use Proper Tools
Always use proper tools which are in good, working condition
during the installation of the Transolid
®
products. Using tools oth-
er than those listed could adversely affect the integrity of oors,
pipes, walls, or this product and could result in water damage
or other damage to oors, pipes, walls, or other portions of your
building or home.
Do Not Use Nails
The panels mount to walls with 100% clear silicone sealant only.
Transolid
®
recommends 100% clear silicone sealant to mount
this product. Never use hammers, nails, or screws. Hammers,
nails and screws could adversely affect the integrity of this prod-
uct. Nails and screws could puncture the Transolid
®
Wall Sys-
tems and Panels, resulting in water or other damage to oors,
pipes, walls or other portions of your building or home.
Inspect Before Cutting
Make sure no electrical wiring or plumbing is present before cut-
ting into a wall to install any accessories.
Wall Conditions
Inspect the walls before installing the Transolid panels. Never in-
stall panels over damp walls or an existing mold condition.
Use Proper Installation Methods
Follow all instructions related to wall surface preparation. Fail-
ure to follow such instructions could cause the panels to detach
from the wall surface after installation, resulting in personal injury.
Failure to follow these instructions could result in water damage.
WARNING
Lifting Hazard
According to the National Institute of Occupational Safety and
Health, the recommended maximum safe lifting weight is 51
pounds, with all lifting conditions perfect - minimal forward reach,
steady load close to the body, straight back, load between knees
and shoulders, and good grips. To avoid personal injury, always
use these proper lifting techniques and use two people to move
carton weighting more than 51 lbs. The box containing Transolid
Saramar
®
kit can weigh in excess of 280 pounds. Use the appro-
priate lifting devices to move the load. Always use two people
when lifting heavy or bulky cartons. DO NOT attempt to lift ob-
jects that are too heavy. When carrying a heavy load - get help!
Room Temperature
Allow Transolid Saramar
®
panels to adjust to room temperature
for at least six hours before installation, and consult the 100% sil-
icone sealant manufacturer’s instructions for storage and surface
preparation. The panels should be installed at temperatures not
less than 65°F. Panels should not be installed in areas where the
temperature may drop below freezing (32°F). Failure to follow
this recommendation could adversely affect the silicone sealants
which holds the panels to the wall. If the panels are not correctly
adhered to the walls, they may fall off, causing possible injury to
someone in or around the shower enclosure.
Eye Protection
Be sure to use all personal protective equipment to ensure your
own safety. To avoid eye injury, always wear protective glasses
with side shields when using power tools. Also, make sure no one
else can be injured by ying particles when using power tools.
Grab Bars
We recommend that shower compartments be equipped with
support grab bars that comply with the most recent edition of AN-
SI-A117.1 requirements. Grab bars must be anchored to struc-
tural support (wall studs) behind the panels. Do not rely on the
panels only for grab bar support.
Personal Protection
Be sure to use all personal protective equipment, such as sturdy
work boots, preferably with steel toes, gloves, and hard hat, if
necessary, to ensure your own safety. To prevent possible dam-
age to your hearing, always wear ear protection, such as ear-
muffs or earplugs, when working around power tools.
Cutting Hazard
The installation of Transolid product may require using power
tools. Keep hands away from the cutting edge of any tool used
in the installation of our product. Place ngers in or around the
cutting blades could result in serous personal injury.
Sharp Edge Hazard
After cutting the edge of a Transolid
®
panel, it can be sharp. Wear
protective gloves to prevent personal injury.
Slipping Hazard
Do not install this product in the presence of water. Installing this
product without drying all surfaces, or in the presence of water,
could cause you to slip and fall due to wet oors or spilled uids.
Personal injury can result from slips or falls. Before installation,
dry all surfaces, including the oor, with a cloth or paper towel.
Clean up all water or spilled uids immediately.
Fire Hazard
Personal injury or death can result from a re caused by am-
mable liquids or silicone sealants. Cleaners or solvents can be
highly explosive, resulting in personal injury or even death, when
not used properly. Clean up any ammable substance immedi-
ately. Sparks or open ames can cause ammable substances to
ignite. DO NOT smoke while working on or near any ammable
substance.
Solvent Hazard
Follow all manufacturer’s safety instructions for silicone seal-
ants and denatured alcohol. Alcohol vapors are both ammable
and hazardous to breathe. Silicone vapors may irritate eyes and
nose. Personal injury can result from improperly handling or use
of products, such as denatured alcohol. Always follow the man-
ufacturer’s recommendations for the safe use of these products.
Ventilate any work area before beginning to apply silicone seal-
ants, cleaning agents, or solvents.
Fumes Hazard
The fumes from the silicone and solvents used by the installer
can be harmful if used in an unventilated room. Always work in a
well ventilated area. To keep the area well-ventilated, open win-
dows and use exhaust fans. If adequate ventilation is not achiev-
able or practical, use respiratory protective equipment.
Dust Hazard
When cutting or drilling Transolid Saramar
®
product, use a dust
collection method which prevents dust particles from going into
the air. Always work in a well-ventilated area. Always use an
OSHA approved dust mask when cutting, drilling, or sanding
Ttransolid
®
products.
Power Tool Hazard
To prevent personal injury or possible death, always follow the
electrical safety recommendations of the power tool’s manufac-
turer. Do not use power tools in an unsafe manner. Power tools
should only be connected to a circuit protected by a ground-fault
circuit interrupter (GFI).
Shock Hazard
Never use electric power tools around water, condensation, or
other liquids. Electric shock can cause severe burns, signicant
injuries, and even death. If an extension cord is required, always
use an OSHA approved extension cord. Power cords should only
be connected to a circuit protected by a ground-fault interrupter
(GFI).
Safety Guidelines