Install Instructions

ManualsBrandsTrapzilla ManualsGrease TrapsSample Port, 0.5" Fall Gradient, 4" Inlet/Outlet

A THERMACO® Technology

A Thermaco, Inc.

Technology • P.O.Box 2548 • Asheboro, NC 27204

(800) 633-4204 • (336) 629-4651

info@thermaco.com • www.trapzilla.com

Installationand Operational Instructions

For Trapzilla

Sample Ports

Part# MNL-TZSP-1

AFE

TZSP-48

Sample Port designed to be installed in

locations requiring vertical waterfall lling

access.

• 7.8” (198 mm) vertical fall

• 4” (102 mm) Inlet/Outlet

TZSP-40

Sample Port designed for retrot installations

on existing lines with no vertical fall.

• 0.5” (12.7 mm) fall

• 4” (102 mm) Inlet/Outlet

A A

B B

C C

D D

       

THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT

WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.

POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF

THIS DRAWING. DO NOT DESTROY THIS DRAWING,

IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.

MATERIAL (UNLESS NOTED)

FINISH (UNLESS NOTED)

646 GREENSBORO STREET

PO BOX 2548, ASHEBORO, NC 27203

VOICE 336-629-4651 FAX 336-626-5739

Decimals

.XX +/- .03

.XXX +/- .015

Unless otherwise specified

Dimensions are in inches

Tolerances

Angular

+/- 1°

CHECKED

SIZE

REV. NO.

DWG NO.

PART NO.

SCALE

RELEASE DATE

SHEET OF

ENGINEERING

DRAWN

DATE

THIRD ANG LE PROJECTIO N

4.5 in

[11.4 cm]

4.5 in

[11.4 cm]

26 in

[66 cm]

22 in

[55.9 cm]

17.8 in

[45.2 cm]

7.8 in

[19.8 cm]

15.6 in

[39.5 cm]

6 in

[15.3 cm]

10 in [25.4 cm]CLEARANCE FROM

TOP OF TANK REQUIRED FOR

LID REMOVAL

OUTLET

INLET

SIDE VIEW

4" PIPE

INLET/OUTLET

END VIEW

TOP VIEW

A A

B B

C C

D D

       

THIS DRAWING CONTAINS PROPRIETARY AND PATENTED MATERIAL. THIS DRAWING MAY NOT BE REPRODUCED IN WHOLE OR PART WITHOUT

WRITTEN CONSENT FROM THERMACO, INC. POSSESSION OF THIS DRAWING DOES NOT CONSTITUTE THE RIGHT TO MANUFACTURE.

POSSESSION OF THIS DRAWING DOES CONSTITUTE AN IMPLIED NONDISCLOSURE AGREEMENT BETWEEN THERMACO, INC. AND THE HOLDER OF

THIS DRAWING. DO NOT DESTROY THIS DRAWING,

IT IS THE SOLE PROPERTY OF THERMACO, INC. AND MUST BE RETURNED UPON REQUEST.

MATERIAL (UNLESS NOTED)

FINISH (UNLESS NOTED)

646 GREENSBORO STREET

PO BOX 2548, ASHEBORO, NC 27203

VOICE 336-629-4651 FAX 336-626-5739

Decimals

.XX +/- .03

.XXX +/- .015

Unless otherwise specified

Dimensions are in inches

Tolerances

Angular

+/- 1°

CHECKED

SIZE

REV. NO.

DWG NO.

PART NO.

SCALE

RELEASE DATE

SHEET OF

ENGINEERING

DRAWN

DATE

THIRD ANG LE PROJECTIO N

4.5 in

[11.4 cm]

4.5 in

[11.4 cm]

26 in

[66.0 cm]

8.3 in

[21.1 cm]

7.8 in

[19.8 cm]

11.1 in

[28.1 cm]

7 in

[17.8 cm]

10 in [25.4 cm]CLEARANCE FROM

TOP OF TANK REQUIRED FOR

LID REMOVAL

INLET

OUTLET

SIDE VIEW

END VIEW

4" PIPE

INLET/OUTLET

TOP VIEW

22 in

[55.9 cm]

Summary of content (11 pages)

PAGE 1
A THERMACO® Technology Installationand Operational Instructions For Trapzilla® Sample Ports 4 3 2 1 4.5 in [11.4 cm] TZSP-48 Sample Port designed to be installed in locations requiring vertical waterfall filling access. D • 7.8” (198 mm) vertical fall D 26 in [66 cm] • 4” (102 mm) Inlet/Outlet C C 4 3 TOP VIEW 2 4.5 in [11.4 cm] 10 in [25.4 cm]CLEARANCE FROM TOP OF TANK REQUIRED FOR LID REMOVAL D 1 4.5 in [11.4 cm] 22 in [55.
PAGE 2
Trapzilla® Sample Ports System Overview A THERMACO® Technology Trapzilla® Sample Port System Overview The Trapzilla® Sample Port provides a convenient, easy method to sample a grease interceptor, process point or other effluent source. Trapzilla’s unique design makes it easy to install in almost any location, be it inside or outside the facility. It also lends itself to many wastewater sites including commercial, industrial, medical and municipal.
PAGE 3
Trapzilla® Sample Ports A THERMACO® Technology TZSP-40 Plumbing Installation The Trapzilla Sample Port is designed with ease of installation in mind. It may be installed inside or outside the facility on the wastewater drainage piping. An optional ECA-TZ-29, field-modifiable extension collar is available to assist with plumbing to drainage piping that is deep in the ground. The ECA-TZ-29 Extension Collar has a telescoping two-piece design for easy setting and trimming in the field. Thermaco, Inc.
PAGE 4
Trapzilla® Sample Ports A THERMACO® Technology TZSP-48 Plumbing Installation The Trapzilla Sample Port is designed with ease of installation in mind. It may be installed inside or outside the facility on the wastewater drainage piping. An optional ECA-TZ-29, field-modifiable extension collar is available to assist with plumbing to drainage piping that is deep in the ground. The ECA-TZ-29 Extension Collar has a telescoping two-piece design for easy setting and trimming in the field. Thermaco, Inc.
PAGE 5
Trapzilla® Sample Ports A THERMACO® Technology Extension Collar Installation Parts Provided with the ECA-TZ-29 Extension Collar In situations where the pipe levels are set at such a depth so that the lid of the Sample Port does not sit at grade level, an extension collar may be necessary. Thermaco sells the ECA-TZ-29 twopiece extension collar with telescoping design which provides up to 29” effective height increase of the unit, permitting the lid to be brought to grade.
PAGE 6
22.00 in 22.00 in [55.9 cm] [55.9 cm] A THERMACO® Technology Trapzilla® Sample Ports Extension Collar Installation The extension collar height as calculated on page 7 determines the steps required to complete the extension collar installation. The ECA-TZ-29 as shipped is naturally adjustable between 17” Top View and 30.5” in height. Top ViewThe following page (page 8) gives instructions for connecting the two collar halves. The remaining pages cover height adjustments. 30.50 in 30.50 in [77.5 cm] [77.
PAGE 7
Trapzilla® Sample Ports A THERMACO® Technology Extension Collar Installation Measure the distance from the desired position for the cover and the top of the Trapzilla Sample Port. Add 1-1/2” to this measurement to account for the lip where the lid normally nests. The new dimension is the calculated height for the extension collar(s). ©2017 Thermaco, Inc. All rights reserved • Patented/Patents Pending • Specifications subject to change without notice MNL-TZSP-1 7 PO Box 2548 • Asheboro, N. C.
PAGE 8
©2017 Thermaco, Inc. All rights reserved • Patented/Patents Pending • Specifications subject to change without notice MNL-TZSP-1 8 PO Box 2548 • Asheboro, N. C. 27204-2548 • (336) 629-4651 • trapzilla.com 4 3 A 646 GREENSBORO STREET PO BOX 2548, ASHEBORO, NC 27203 VOICE 336-629-4651 FAX 336-626-5739 2 PART NO. FINISH (UNLESS NOTED) ENGINEERING CHECKED Angular +/- 1° DRAWN Bolt MATERIAL (UNLESS NOTED) Decimals .XX +/- .03 .XXX +/- .
PAGE 9
Trapzilla® Sample Ports Extension Collar Installation A THERMACO® Technology Setting the Adjusted Collar Height Figure 1 1) Extend the collar to match the calculated height as determined on page 7. 2) Unscrew the brass nuts and remove the 22” Diameter Cover from the Trapzilla Sample Port. 3) Using the instructions found on page 8, bolt the two pieces of the Extension Collar together. Use Silicone Sealant (not provided) to seal the space between the two sections of the collar.
PAGE 10
Trapzilla® Sample Ports A THERMACO® Technology Extension Collar Installation Trimming the ECA Extension Collar Upper (Inner) Section: Measure from the Bottom and cut at the bottom of the section. Lower (Outer) Section: Measure from the Top and cut at the top of the section. When trimming the ECA Extension Collar, ALWAYS: 1) Measure from the Top of the Lower (Outer) section & cut the top of the section. 2) Measure from the Bottom of the Upper (Inner) section and cut at the bottom of the section.
PAGE 11
Trapzilla® Sample Ports A THERMACO® Technology Limited Warranty & Remedy Thermaco, Inc. warrants to the original user that the products manufactured by it delivered with this warranty shall be free from material defects in workmanship and materials for a period of 12 months from the date of invoice to the distributor (if sold by an authorized Thermaco distributor) or the date of invoice to the purchaser (if sold directly by Thermaco, Inc.