INTRODUCTION TABLE OF CONTENTS 3 BEFORE YOU PROCEED 4 SAFETY PRECAUTIONS 5 TOOLS, SUPPLIES AND REQUIRED EQUIPMENT 6 TRAXXAS RALLY MODEL OVERVIEW 7 QUICK START: GETTING UP TO SPEED 8 TQi RADIO AND VELINEON BRUSHLESS POWER SYSTEM 16 ADJUSTING THE ELECTRONIC SPEED CONTROL 18 DRIVING YOUR MODEL 20 BASIC TUNING ADJUSTMENTS 22 MAINTAINING YOUR MODEL 23 ADVANCED TUNING ADJUSTMENTS 27 TQi ADVANCED TUNING GUIDE 2 • TRAXXAS RALLY Thank you for purchasing the Traxxas Rally equipped with the Velineon® Brushless
BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. SUPPORT Before running your model, look over this entire manual and examine the model carefully. If for some reason you decide it is not what you wanted, then do not continue any further. Your hobby dealer absolutely cannot accept a model for return or exchange after it has been run.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model. Skill Level = Myriad Semi Bold This model is not intended for use by children under 14=years of age Skill Level Myriad Semi Bold without the supervision of a responsible Level = Myriad Semi Bold and knowledgeable adult. bluehighway font Gearing and battery choice (see LiPo Batteries, right) Level = Myriad Semi Bold effect the skill level of the bluehighway model.
TOOLS, SUPPLIES AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Supplied Tools and Equipment • Outils et équipements fournis • Equipo y herramientas suministradas • Mitgeliefertes Werkzeug und Ausrüstung 2.5mm “L” wrench Clé “L” de 2,5mm Llave Allen de 2.5 mm 2,5 mm Innensechskantschlüssel 2.0mm “L” wrench Clé “L” de 2,0mm Llave Allen de 2.
MODEL OVERVIEW Spur Gear Pignon droit Engranaje cilíndrico Zahnrad Traxxas High-Current Connector Connecteur haut courant de Traxxas Conector de alta corriente de Traxxas Traxxas Hochstrom-Anschluss Battery Pile Batería Batterie Half Shaft Demi arbre Semieje Halbwelle Battery Hold-Down Support de pile Sujeción de la batería Batterieniederhalter Caster Block Blocage de la roulette Bloqueo del eje delantero Nachlaufblockierung Drive Shaft Arbre de transmission Eje de la transmisión Antriebswelle Chassis
QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on page 4 For your own safety, understand where carelessness and misuse could lead to personal injury and product damage. 2. Charge the battery pack • See page 11 Fully charge the included battery pack. Begin charging your battery right away. 3.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM INTRODUCTION Applying the Decals The main decals for your model have been applied at the factory. The decals are printed on self-adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it from the backing. Your model includes the latest Traxxas TQi 2.4GHz transmitter with Traxxas Link™ Model Memory.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM Good charging procedures are required to reduce the possibility of developing a “memory” effect and shortened run times. NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH batteries offer high current handling, and much greater resistance to the “memory” effect. NiMH batteries generally allow higher capacity than NiCad batteries. They can last up to 500 charge cycles. A peak charger designed for NiMH batteries is required for optimal performance.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM ESC/Motor Wiring Diagram Your model is equipped with the newest TQi 2.4GHz transmitter with Traxxas Link™ Model Memory. The transmitter has two channels for controlling your throttle and steering. The receiver inside the model has 5 output channels. Your model is equipped with one servo and an electronic speed control.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM INSTALLING TRANSMITTER BATTERIES Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. CHARGING THE BATTERY PACK Use the included charger to charge the included battery pack. The battery pack should be removed from the vehicle before charging. Do not leave the battery unattended while charging.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM INSTALLING THE BATTERY PACK The following Traxxas High Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector. Part #3060 Single Male/Female Install the battery pack with the battery wires facing the rear of the model. Insert the tabs of the battery hold-down into the slots in the rear hold-down retainer (A).
TRAXXAS TQi RADIO & VELINEON Power SYSTEM RADIO SYSTEM CONTROLS • In order for the transmitter and receiver to bind to one another, the receiver in the model must be turned on within 20 seconds of turning on the transmitter. The transmitter LED will flash fast red indicating a failure to link. If you miss it, simply turn off the transmitter and start over. Remember, always turn the TQi transmitter on first and off last to avoid damage to your model.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM Using the Radio System Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. The TQi Radio System has been pre-adjusted at the factory. The adjustment should be checked before running the model, in case of movement during shipping. Here’s how: 1. Turn the transmitter switch on.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM 3. When the transmitter and receiver’s LEDs turn solid green, the system is bound and ready for use. Confirm that the steering and throttle operate properly before driving your model. Steering Sensitivity (Exponential) The Multi-Function knob on the TQi transmitter has been programmed to control Steering Sensitivity (also known as exponential).
ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s Specifications Input voltage: 4.8-11.1V (4 to 9 cells NiMH or 2S to 3S LiPo) Supported Motors: Brushed Sensored brushless Sensorless brushless Motor limit: None Continuous current: 200A Peak current : 320A BEC voltage: 6.0V DC Transistor type: MOSFET Battery connector: Traxxas High-Current Connector Motor connectors: TRX 3.
ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s Profile Selection The speed control is factory set to Profile #1 (100% forward, brakes, and reverse). To disable reverse (Profile #2) or to allow 50% forward and 50% reverse (Profile #3), follow the steps below. The speed control should be connected to the receiver and battery, and the transmitter should be adjusted as described previously. The profiles are selected by entering the programming mode.
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly important when using high capacity battery packs that allow extended periods of running. Monitoring temperatures will extend the lives of the batteries and motors.
DRIVING YOUR MODEL tires if holes are not cut in the tires. Cut two small holes (3mm or 1/8” diameter) in each tire. Each hole should be near the tire center-line, 180 degrees apart. 3. Confirm that the RX box O-ring and cover are installed correctly and secure. Make sure the screws are tight and the blue O-ring is not visible protruding from the edge of the cover. 4. Confirm that your batteries can be used in wet conditions. 5.
BASIC TUNING ADJUSTMENTS All of the toe links are installed on the model so the left hand thread indicators point to the same direction. This makes it easier to remember which way to turn the wrench to increase or decrease toe link length (the direction is same at all four corners). Note that the groove in the hex indicates the side of the toe link with the left-hand threads.
BASIC TUNING ADJUSTMENTS Fine Tuning the Shocks The four shocks on the model influence its handling. Whenever you rebuild your shocks, or make any changes to the pistons, springs or oil, always make changes to them in pairs (front or rear). Piston selection depends on the range of oil viscosities that you have available. For example, using a two-hole piston with a lightweight oil will, at one point, give you the same damping as a threehole piston with heavier oil.
MAINTAINING YOUR MODEL Always wear eye protection when using compressed air or spray cleaners and lubricants. High performance vehicles generate small vibrations while driving. These vibrations may loosen hardware over time and require attention. Always check your wheel nuts and other hardware and tighten or replace when necessary. Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously.
ADVANCED TUNING ADJUSTMENTS Your model has provisions for adjusting the camber gain geometry of the front and rear suspension. “Camber gain” refers to an increase in camber angle as the suspension is compressed. The camber gain of the vehicle can be changed by moving the camber link attachment to a different horizontal mounting position. Adjusting the camber gain will alter the tire contact patch as the suspension is compressed. Making the camber link shorter will increase the camber gain.
ADVANCED TUNING ADJUSTMENTS Velineon 3500 Specs Type: Sensorless brushless RPM/volt: 3500 (10-turn) Magnet type: Ultra High-Temperature Sintered Neodymium Connection type : 3.5mm bullet Wire size: 12 Gauge Current Ratings: 200A constant 320A peak/burst Max RPM: 50,000 Diameter: 36mm (1.42) (540 size) Length: 55mm (2.165) Weight: 262g (9.24oz) Always use the proper length motor bolts. The standard motor mounting bolts are 3x8mm.
ADVANCED TUNING ADJUSTMENTS Brushed Motors For the ultimate in versatility, the VXL-3s has no motor limit when used with a brushed motor. This allows you to use any readily available 540 or 550 size brushed motors in your VXL-3s equipped vehicle. Always be sure to follow all break in and maintenance instructions set forth by the motor manufacturer. The VXL-3s automatically detects what kind of motor it is connected to so no programming actions are required to use brushed motors.
ADVANCED TUNING ADJUSTMENTS Follow the steps on the following page to access and refill the front and rear differentials. Front differential: 1. Remove the two 3x15mm button-head screws that secure the upper bumper/body mount to the differential (diff) case. 2. Turn the chassis over and remove the three 4x10mm countersunk screws that hold bumper/skid plate to the bulkhead. The two rear screws do not need to be removed. 3. Slide bumper/body mount assembly off of the chassis. 4.
TQi ADVANCED TUNING GUIDE Your Traxxas transmitter has a programmable Multi-Function knob that can be set to control various advanced transmitter functions (set to Steering Sensitivity by default, see page 15). Accessing the programming menu is done by using the menu and set buttons on the transmitter and observing signals from the LED. An explanation of the menu structure follows on page 29. Experiment with the settings and features to see if they can improve your driving experience.
TQi ADVANCED TUNING GUIDE Failsafe Your Traxxas radio system is equipped with a built-in failsafe function that returns the throttle to its last saved neutral position in the event of a signal loss. The LED on the transmitter and the receiver will rapidly flash red. Model Lock The Traxxas Link Model Memory feature can store up to thirty models (receivers) in its memory.
TQi ADVANCED TUNING GUIDE Press MENU to move through options. Press SET to select an option. MENU TREE The menu tree below shows how to navigate through the TQi transmitter’s various settings and functions. Press and hold MENU to enter the menu tree, and use the following commands to navigate through the menu and select options. MENU: When you enter a menu, you always start at the top. Press MENU to move down the menu tree.
TQi ADVANCED TUNING GUIDE x8 Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press SET to confirm green LED blinks (x8) Set Multi-Function knob for THROTTLE SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU to confirm red LED blinks (x2) Set Multi-Function knob for STEERING DUAL RATE (%) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU twice red LED blinks (x3) Set Multi-F
TQi ADVANCED TUNING GUIDE PROGRAMMING YOUR TQi TRANSMITTER WITH YOUR APPLE iPHONE OR iPOD TOUCH The Traxxas Docking Base (Part #6510 - sold separately) for the TQi transmitter installs in minutes to transform your iPhone® or iPod touch® into a powerful tuning tool that allows you to replace the transmitter’s button/LED programming system with an intuitive, high-definition, fullcolor graphical user interface.
BOTTOM 2 3 4 5 Piston: 2-hole Silver Battery Placement: Front Rear Weight Bias: Front _____% Rear _____% Weight: _______lbs.
2 3 4 5 A B C X X front shocks Negative 1 ° 6 X Top Bottom Piston: 2-hole Silver Battery Placement: Front X Rear Weight Bias: Front _____% Rear _____% Weight: _______lbs.
2 3 4 5 A B C X X front shocks Negative 1 ° 8 X Top Bottom X Piston: 2-hole Silver Battery Placement: Front X Rear Weight Bias: Front _____% Rear _____% Weight: _______lbs.
1100 Klein Road, Plano Texas 75074 1-888-TRAXXAS 120912 7407OM-N-EN-R00
MODEL 7407 owner’s manual