owners manual MODELL 37076-4 MODELL 36076-4 MODELL 24076-4 extreme brushless power system
INTRODUCTION 3 BEFORE YOU PROCEED 4 SAFETY PRECAUTIONS 7 TOOLS, SUPPLIES AND REQUIRED EQUIPMENT 8 ANATOMY OF THE RUSTLER VXL 9 ANATOMY OF THE STAMPEDE VXL 10 ANATOMY OF THE BANDIT VXL 11 QUICK START: GETTING UP TO SPEED 12 TRAXXAS TQi RADIO AND VELINEON POWER SYSTEM 20 ADJUSTING THE ELECTRONIC SPEED CONTROL 22 DRIVING YOUR MODEL 24 BASIC TUNING ADJUSTMENTS 26 MAINTAINING YOUR MODEL 27 ADVANCED TUNING ADJUSTMENTS 28 TQi ADVANCED TUNING GUIDE Thank you for purchasing a Traxxas electric
BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and examine the model carefully. If for some reason you decide it is not what you wanted, then do not continue any further. Your hobby dealer absolutely cannot accept a model for return or exchange after it has been run.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model. This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. Gearing and battery choice (see LiPo Batteries, right) effect the skill level of the model. See chart below. Gearing: Battery: Voltage*: mAh: Stock Pinion 6-Cell NiMH 7.2V 3000+mAh Gearing: Battery: Voltage*: mAh: Opt.
SAFETY PRECAUTIONS WARNING! CAUTION! DANGER! FIRE HAZARD! Your model is able to use LiPo batteries. Charging and discharging batteries has the potential for fire, explosion, serious injury, and property damage if not performed per the instructions. Before use, read and follow all manufacturer’s instructions, warnings, and precautions.
SAFETY PRECAUTIONS (continued from previous page) • ALWAYS charge batteries in a well-ventilated area. • REMOVE flammable items and combustible materials from the charging area. • DO NOT leave the charger and battery unattended while charging, discharging, or anytime the charger is ON with a battery connected. If there are any signs of a malfunction or in the event of an emergency, unplug the charger from the power source and disconnect the battery from the charger.
TOOLS, SUPPLIES AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Supplied Tools and Equipment 2.5mm “L” wrench Optional Pinion Gear see page 27 2.0mm “L” wrench 1.
ANATOMY OF THE RUSTLER VXL Turnbuckle (Rear Camber Link ) Electronic Speed Control (VXL-3s) Half Shaft EZ-Set® Button (On/Off Button) Steering Block Caster Block Rear Shock Tower Battery Compartment Traxxas HighCurrent Connector Rear Body Mount Chassis Transmission Battery Hold-Down Brushless Motor (Velineon® 3500) Turnbuckle (Front Camber Link ) Front Body Mount Suspension Arm (Front) Pinion Gear Front Bumper Gear Cover (ghosted) Light Pipe Spur Gear Slipper Clutch Receiver Box Antenna Mou
ANATOMY OF THE STAMPEDE VXL Shock (Oil Damper) Half Shaft Steering Block Electronic Speed Control (VXL-3s) Suspension Arm (Rear) Traxxas HighCurrent Connector Rear Body Mount Chassis Brushless Motor (Velineon® 3500) Transmission EZ-Set® Button (On/Off Button) Battery Compartment Battery Hold-Down Caster Block Suspension Arm (Front) Bulkhead Front Bumper Wheelie Bar Receiver Box Pinion Gear Light Pipe Spur Gear Steering Servo Antenna Mount Front Shock Tower Turnbuckle (Rear Camber Link )
ANATOMY OF THE BANDIT VXL Turnbuckle (Rear Camber Link ) Electronic Speed Control (VXL-3s) Battery Compartment Steering Block Half Shaft Rear Shock Tower Rear Body Mount Traxxas HighCurrent Connector Battery Hold-Down EZ-Set® Button (On/Off Button) Chassis Caster Block Turnbuckle (Front Camber Link ) Brushless Motor (Velineon® 3500) Suspension Arm (Front) Transmission Pinion Gear Front Bumper Gear Cover Front Body Mount (ghosted) Light Pipe Receiver Box Spur Gear Antenna Mount Slipper
QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on page 4-6 For your own safety, understand where carelessness and misuse could lead to personal injury. 2. Charge the battery pack • See page 15 Your model requires a battery pack and a compatible battery charger (not included). Never use a NiMH or NiCad charger to charge LiPo batteries.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM INTRODUCTION Applying the Decals The main decals for your model have been applied at the factory. The decals are printed on self-adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it from the backing. Your model includes the latest Traxxas TQi 2.4GHz transmitter with Traxxas Link™ Model Memory.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH batteries offer high current handling, and much greater resistance to the “memory” effect. NiMH batteries generally allow higher capacity than NiCad batteries. They can last up to 500 charge cycles. A peak charger designed for NiMH batteries is required for optimal performance. Receiver - The radio unit inside your model that receives signals from the transmitter and relays them to the servos.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM Velineon 3500 Specs Type: Sensorless brushless RPM/volt: 3500 Magnet type: Ultra HighTemperature Sintered Neodymium Connection type : 3.5mm bullet Wire size: 12 Gauge Max RPM: 50,000 Diameter: 36mm (1.42") (540 size) Length: 55mm (2.165") Weight: 262g (9.24oz) Your model is equipped with the newest TQi 2.4GHz transmitter with Traxxas Link™ Model Memory. The transmitter has two channels for controlling your throttle and steering.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM INSTALLING TRANSMITTER BATTERIES Your TQi 2.4GHz transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. SELECTING A CHARGER AND BATTERIES FOR YOUR MODEL Your model does not include a battery or charger. The speed control in the model is compatible with both LiPo and NiMH batteries. One NiMH or 2s LiPo battery equipped with a Traxxas High Current connector is required.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM Battery iD Traxxas recommended battery packs are equipped with Traxxas Battery iD. This exclusive feature allows Traxxas battery chargers (sold separately) to automatically recognize connected battery packs and optimize the charge settings for the battery. This eliminates the need to worry over charger settings and menus for the easiest and safest charging solution possible. Visit Traxxas.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM RADIO SYSTEM CONTROLS • In order for the transmitter and receiver to bind to one another, the receiver in the model must be turned on within 20 seconds of turning on the transmitter. The transmitter LED will flash fast red indicating a failure to link. If you miss it, simply turn off the transmitter and start over. TUR N GH RI T Remember, always turn the TQi transmitter on first and off last to avoid damage to your model.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. 5. Turn the steering wheel on the transmitter back and forth and check for rapid operation of the steering servo. Also, check that the steering mechanism is not loose or binding. If the steering operates slowly, check for weak batteries. 6.
TRAXXAS TQi RADIO & VELINEON POWER SYSTEM TRAXXAS STABILITY MANAGEMENT (TSM) Traxxas Stability Management or TSM allows you to experience all the speed and acceleration that was engineered into your Traxxas model by helping you to maintain control of the vehicle in low-traction situations. TSM helps provide straight ahead full-throttle acceleration on slippery surfaces, without fishtailing, spinouts, or loss of control. TSM also dramatically improves braking control.
ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s Specifications Input voltage: 4.8-11.1V (4 to 9 cells NiMH or 2S to 3S LiPo) Supported Motors: Brushless Motor limit: None Continuous current: 200A Peak current : 320A BEC voltage: 6.0V DC Transistor type: MOSFET Battery connector: Traxxas High-Current Connector Motor connectors: TRX 3.5mm bullet connectors Motor/Battery Wiring: 12-gauge Maxx® Cable Thermal Protection: 2-stage thermal shutdown The VXL-3s features Locked Rotor Protection.
ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s Profile Selection The speed control is factory set to Profile #1 (100% forward, brakes, and reverse). To disable reverse (Profile #2) or to allow 50% forward and 50% reverse (Profile #3), follow the steps below. The speed control should be connected to the receiver and battery, and the transmitter should be adjusted as described previously. The profiles are selected by entering the programming mode.
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly important when using high capacity battery packs that allow extended periods of running. Monitoring temperatures will extend the lives of the batteries and motors.
DRIVING YOUR MODEL 2. The wheels have small holes molded in to allow air to enter and exit the tire during normal running. Water will enter these holes and get trapped inside the tires if holes are not cut in the tires. Cut two small holes (3mm or 1/8” diameter) in each tire. Each hole should be near the tire centerline, 180 degrees apart. 3. Confirm that the RX box O-ring and cover are installed correctly and secure.
BASIC TUNING ADJUSTMENTS All of the toe links are installed on the truck so the left hand thread indicators point to the same direction. This makes it easier to remember which way to turn the wrench to increase or decrease toe link length (the direction is same at all four corners). Note that the groove in the hex indicates the side of the toe link with the left-hand threads.
BASIC TUNING ADJUSTMENTS Adjusting the Slipper Clutch The model is equipped with an adjustable slipper clutch which is built into the large spur gear. The Tighten purpose of the slipper clutch is to regulate the amount of power sent to the rear wheels to prevent tire spin. When it slips, the slipper clutch Loosen makes a high-pitch, whining noise. Remove the rubber slipper clutch plug on the transmission cover in order to adjust the slipper.
MAINTAINING YOUR MODEL Always wear eye protection when using compressed air or spray cleaners and lubricants. High performance vehicles generate small vibrations while driving. These vibrations may loosen hardware over time and require attention. Always check your wheel nuts and other hardware and tighten or replace when necessary. Always use the proper length motor bolts. The standard motor mounting bolts are 3x8mm.
ADVANCED TUNING ADJUSTMENTS # Spur Gear Teeth x 2.72 = Final Gear Ratio # Pinion Gear Teeth LiPo Batteries LiPo batteries are intended only for the most advanced users that are educated on the risks associated with LiPo battery use. It is critical to follow all instructions supplied by the battery manufacturer and the charger manufacturer for proper charging, use, and storage of LiPo batteries. Make sure you understand how to use your LiPo batteries.
TQi ADVANCED TUNING GUIDE Starting Over: Restoring Factory Defaults When programming your TQi transmitter, you may feel the need to start over with a clean slate. Follow these simple steps to restore the factory settings: 1. Turn transmitter off. 2. Hold both MENU and SET. 3. Turn transmitter on. 4. Release MENU and SET. The transmitter LED will blink red. 5. Press MENU once. The transmitter LED will blink red twice repeatedly. 6. Press SET to clear settings.
TQi ADVANCED TUNING GUIDE Steering and Throttle End Points The TQi transmitter allows you to choose the limit of the servo’s travel range (or its “end point”) independently for left and right travel (on the steering channel) and throttle/brake travel (on the throttle channel). This allows you to fine-tune the servo settings to prevent binding caused by the servo moving steering or throttle linkages (in the case of a nitro model) farther than their mechanical limits.
TQi ADVANCED TUNING GUIDE TRAXXAS LINK MODEL MEMORY Traxxas Link Model Memory is an exclusive, patent-pending feature of the TQi transmitter. Each time the transmitter is bound to a new receiver, it saves that receiver in its memory along with all the settings assigned to that receiver. When the transmitter and any bound receiver are switched on, the transmitter automatically recalls the settings for that receiver. There is no need to manually select your vehicle from a list of model memory entries.
TQi ADVANCED TUNING GUIDE Press MENU to move through options. Press SET to select an option. MENU TREE The Menu Tree below shows how to navigate through the TQi transmitter’s various settings and functions. Press and hold MENU to enter the Menu Tree, and use the following commands to navigate through the menu and select options. MENU: When you enter a menu, you always start at the top. Press MENU to move down the Menu Tree.
TQi ADVANCED TUNING GUIDE x8 Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press SET to confirm green LED blinks (x8) Set Multi-Function knob for THROTTLE SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU to confirm red LED blinks (x2) Set Multi-Function knob for STEERING DUAL RATE (%) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU twice red LED blinks (x3) Set Multi-F
TQi ADVANCED TUNING GUIDE PROGRAMMING YOUR TQi TRANSMITTER WITH YOUR APPLE iPHONE, iPAD, iPOD TOUCH, OR ANDROID MOBILE DEVICE The Traxxas Link™ Wireless Module (part #6511, sold separately) for the TQi transmitter installs in minutes to transform your Apple® iPhone®, iPad®, iPod touch®, or Android™ device into a powerful tuning tool that allows you to replace the transmitter’s button/LED programming system with an intuitive, high-definition, full-color graphical user interface.
6250 Traxxas Way, McKinney, TX 75070 1-888-TRAXXAS 210115 24076-36076-37076-4-OM-EN-R06
