Instructions

10
•
T-MAXX 3.3 OWNER’S MANUAL
Range-Testing the Radio System
Before each running session with your model, you
should range-test your radio system to ensure that it
operates properly.
1.
Turn on the radio system
and check its operation as
described in the previous
section.
2.
Have a friend hold the model
with the engine off.
3. Walk away from the model
with the transmitter until you
reach the farthest distance
you plan to operate the
model.
4.
Operate the controls on the
transmitter once again to be
sure that the model responds
correctly.
5.
Do not attempt to operate
the model if there is any
problem with the radio system or any external interference with
your radio signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the limit
of radio range. At 60mph, a model can cover 88 feet every second! It’s
a thrill, but use caution to keep your model in range. If you want to see
your model achieve its maximum speed, it is best to position yourself
in the middle of the truck’s running area, not the far end, so you drive
the truck towards and past your position. In addition to maximizing
the radio’s range, this technique will keep your model closer to you,
making it easier to see and control.
No matter how fast you drive your model, always leave adequate
space between you, the model, and others. Never drive directly
toward yourself or others.
TQi Binding Instructions
For proper operation, the transmitter and receiver must be
electronically ‘bound.’ This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions. Note: the receiver
must be connected to a 4.8-6.0v (nominal) power source for binding
and the transmitter and receiver must be within 5 feet of each other.
1. Press and hold the transmitter’s SET button as you switch
transmitter on. The transmitter’s LED will flash red slowly.
Release the SET button.
2. Press and hold the receiver’s LINK button as you switch on
the model. Release the LINK button.
3. When the transmitter and receiver’s LEDs turn solid green, the
system is bound and ready for use. Confirm that the steering and
throttle operate properly before driving your model.
TRAXXAS STABILITY MANAGMENT (TSM)
Traxxas Stability Management or TSM
allows you to experience all the speed
and acceleration that was engineered
into your Traxxas model by helping you
to maintain control of the vehicle in low-traction situations. TSM helps
provide straight ahead full-throttle acceleration on slippery surfaces,
without fishtailing, spinouts, or loss of control. TSM also dramatically
improves braking control. High speed cornering and control is also
made possible as TSM makes corrections for you, without intruding on
your fun, or creating unexpected side effects.
The Multi-Function knob on the TQi
transmitter has been programmed
to control TSM. The recommended
(default) setting for TSM is to rotate
the knob to the 12:00 position (the
zero mark on the dial).
Turn the knob clockwise to
increase assistance; turn the
knob counterclockwise to
decrease assistance. Turn the
knob counterclockwise to its
stop to turn TSM completely off.
Note: TSM is deactivated
automatically when driving or
braking in reverse.
When driving on surfaces with some
traction, decrease the TSM setting to allow the vehicle to feel more
“loose” for power sliding, drifting, and so on. On surfaces with very
little traction (loose dirt, smooth concrete, ice/snow), increase TSM to
maximize acceleration and control.
Drive with TSM on and off to test how it is making your control of
the vehicle easier and more precise. For more information, visit
Traxxas.com/tsm.
Note: TSM must be completely turned off while adjusting steering trim.
SETTING UP THE ANTENNA
The receiver antenna has been set up and
installed from the factory.
When installing the antenna, first slide
the antenna wire into the bottom of the
antenna tube until the white tip of the
antenna is at the top of the tube under
the black cap. Next insert the antenna
tube into the mount while making sure
that antenna wire is in slot in the antenna
mount.
Do not bend or kink the antenna
wire! Do not shorten the antenna tube.
Throttle/Brake
Servo
Steering
Servo
Throttle
Brake
T-Maxx 3.3
Servo Operation
TRAXXAS TQ i RADIO SYSTEM
To prevent loss of radio
range, do not kink or cut
the black wire, do not
bend or cut the metal tip,
and do not bend or cut
the white wire at the end
of the metal tip.
Correct
NoNo No
Antenna
Tip
Antenna
Tube
Antenna
Wrench
Antenna
Crimp Nut
Antenna
Post
Recommended setting
Decrease
assistance
Increase
assistance
TSM off