Instructions

T-MAXX 3.3 OWNER’S MANUAL
•
31
* Optional requires 4995X reverse kit.
Set Multi-Function
knob for STEERING
SENSITIVITY (Expo)
Press/hold MENU
green LED blinks
Press SET
red LED blinks
x
8
Press SET to confirm
green LED blinks (x8)
Press/hold MENU
returns to driving mode
Set Multi-Function
knob for THROTTLE
SENSITIVITY (Expo)
Press/hold MENU
green LED blinks
Press SET
red LED blinks
x
2
Press MENU to confirm
red LED blinks (x2)
x
8
Press SET to select
green LED blinks (x8)
Press/hold MENU
returns to driving mode
Set Multi-Function
knob for STEERING
DUAL RATE (%)
Press/hold MENU
green LED blinks
Press SET
red LED blinks
x
3
Press MENU twice
red LED blinks (x3)
x
8
Press SET to select
green LED blinks (x8)
Press/hold MENU
returns to driving mode
Set Multi-Function
knob for BRAKING
PERCENTAGE (%)
Press/hold MENU
green LED blinks
Press SET
red LED blinks
x
4
Press MENU 3 times
red LED blinks (x4)
x
8
Press SET to select
green LED blinks (x8)
Press/hold MENU
returns to driving mode
Set Multi-Function
knob for
THROTTLE TRIM
Press/hold MENU
green LED blinks
Press SET
red LED blinks
x
5
Press MENU 4 times
red LED blinks (x5)
x
8
Press SET to select
green LED blinks (x8)
Press/hold MENU
returns to driving mode
Adjust the Multi-
Function knob until the
LED turns solid green.
To LOCK the
Multi-Function knob
Press/hold MENU
green LED blinks
Press SET
red LED blinks
x
6
Press MENU 5 times
red LED blinks (x6)
x
8
Press SET to lock
green LED blinks (x8)
Press/hold MENU
returns to driving mode
To REVERSE
the direction of
STEERING servo
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
Press SET
red LED blinks
x
8
Press SET to reverse
servo direction
Press/hold MENU
returns to driving mode
To set the SUB TRIM
of the STEERING
servo
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
Press SET
red LED blinks
x
2
Press MENU
red LED blinks (x2)
Use Multi-Function
knob to set neutral
x
8
Press SET
to save position
Press/hold MENU
returns to driving mode
To set the END
POINTS of the
STEERING servo
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
Press SET
red LED blinks
x
3
Press MENU twice
red LED blinks (x3)
Turn steering
wheel to desired max
left and right travel
x
8
Press SET
to save each position
Turn steering wheel
to test settings
IF END POINTS
ARE OK:
Press/hold MENU
returns to driving mode
IF END POINTS
NEED TO BE
CHANGED:
Press SET
and repeat steps 6-8
To reset the END
POINTS of STEERING
servo to defaults
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
Press SET
red LED blinks
x
4
Press MENU 3 times
red LED blinks (x4)
x
8
Press SET
to reset end points
Press/hold MENU
returns to driving mode
To REVERSE
the direction of
THROTTLE servo
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
red LED blinks
x
8
Press SET to reverse
servo direction
Press/hold MENU
returns to driving mode
To set the SUB TRIM
of the THROTTLE
servo
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
red LED blinks
x
2
Press MENU
red LED blinks (x2)
Use Multi-Function
knob to set neutral
x
8
Press SET
to save position
Press/hold MENU
returns to driving mode
To set the END
POINTS of the
THROTTLE servo
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
red LED blinks
x
3
Press MENU twice
red LED blinks (x3)
Use throttle
trigger to set desired
max throttle or brake
Press SET to save
Use trigger to test
IF END POINTS
ARE OK:
Press/hold MENU
returns to driving mode
IF END POINTS
NEED TO BE
CHANGED:
Press SET
and repeat steps 7-9
To reset the END
POINTS of THROTTLE
servo to defaults
Press/hold MENU
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
green LED blinks
x
2
Press MENU
green LED blinks (x2)
Press SET
red LED blinks
x
4
Press MENU 3 times
red LED blinks (x4)
x
8
Press SET
green LED blinks (x8)
Press/hold MENU
returns to driving mode
MENU TREE FORMULAS
To select functions and make adjustments to the TQi transmitter
without referencing the menu tree, turn your transmitter on, find the
function in the left column you wish to adjust, and simply follow the
corresponding steps .
Always turn your
transmitter on first.
1
Press MENU to move through options.
Press SET to select an option.
Press MENU to move through options.
Press SET to select an option.
Press SET to select an option.
Enter Programming
Press and hold
MENU for 3 seconds
Steering Sensitivity (Expo)
One Blink Red
1
Electric
One Blink Red
1
Unlock
One Blink Red
1
Confirm Deletion
One Blink Red
1
Multi-Function Knob
One Blink Green
1
Channel Setup
Two Blinks Green
2
Mode Selection
Three Blinks Green
3
Traxxas Link
Four Blinks Green
4
Steering (Channel 1)
One Blink Green
1
Model Locking
One Blink Green
1
Shift (Channel 3)*
Three Blinks Green
3
Throttle (Channel 2)
Two Blinks Green
2
Delete Model
Two Blinks Green
2
Throttle Sensitivity (Expo)
Two Blinks Red
2
Nitro
Two Blinks Red
2
Lock
Two Blinks Red
2
Steering % (Dual Rate)
Three Blinks Red
3
Unlock All
Three Blinks Red
3
Braking %
Four Blinks Red
4
Throttle Trim
Five Blinks Red
5
Knob Disabled
Six Blinks Red
6
Press
MENU
Press
MENU
Press
MENU
Press
MENU
Press
MENU
Press
MENU
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Press
SET
Servo Reversing
One Blink Red
1
Press SET to reverse
servo direction.
Servo Reversing
One Blink Red
1
Press SET to reverse
servo direction.
Servo Reversing
One Blink Red
1
Press SET to reverse
servo direction.
Reset End Points
Four Blinks Red
4
Press SET to restore
factory default endpoints.
Reset End Points
Four Blinks Red
4
Press SET to restore
factory default endpoints.
Sub-Trim
Two Blinks Red
2
Use knob to adjust
sub-trim. Press SET to save.
Sub-Trim
Two Blinks Red
2
Use knob to adjust
sub-trim. Press SET to save.
End Points
Three Blinks Red
3
Use steering wheel to
adjust. Turn right to desired
end point, press set to save.
Turn left to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
The menu tree below shows how to navigate through the
TQi transmitter’s various settings and functions. Press and
hold MENU to enter the menu tree, and use the following
commands to navigate through the menu and select options.
MENU:
When you enter a menu, you always start at the top. Press
MENU to move down the menu tree. When you reach the
bottom of the tree, pressing MENU again will return you
to the top.
SET:
Press SET to move across the menu tree and select
options. When an option is committed to the
transmitter’s memory, the status LED will rapidly blink
green.
BACK:
Press both MENU and SET to go back one level in the
menu tree.
EXIT:
Press and hold MENU to exit programming. Your selected
options will be saved.
ECHO:
Press and hold SET to activate the “echo” function. Echo
will “play back” your current position on the Menu Tree,
should you lose your place. For example: If your current
position is Steering Channel End Points, holding SET will
cause the LED to blink green twice, green once, and then
red three times. Echo will not alter your adjustments or
change your position in the programming sequence.
MENU TREE
Below is an example of how to access a function in the menu
tree. In the example, the user is setting the Multi-Function knob
to be a Steering % (Dual Rate) control.
To set the Multi-Function knob to control STEERING % (DUAL RATE):
1. Switch the transmitter on.
2. Press and hold MENU until the green LED lights. It will blink in single intervals.
3. Press SET. The red LED will blink in single intervals to indicate Steering
Sensitivity (Expo) has been selected.
4. Press MENU twice. The red LED will blink three times repeatedly to indicate
Steering % (Dual Rate) has been selected.
5. Press SET to select. The green LED will blink 8 times fast to indicate
successful selection.
6. Press and hold MENU to return to driving mode.
Note: The transmitter is “live” during programming
so you can test the settings real time without having
to exit the menu tree.
End Points
Three Blinks Red
3
Use trigger to adjust. Pull
back to desired end point,
press set to save. Push
forward to desired endpoint and press set to save.
To reset max throw: Let go of controls and press SET.
Press
SET
Restoring Factory Defaults:
Transmitter
OFF
Hold both
MENU and SET
Transmitter
ON
Release MENU and
SET. Red LED blinks
Press MENU four
times. Red LED
blinks 5 times
Press SET to clear settings. LED will turn solid
green. Transmitter is restored to default
*Torque Control is a feature designed only for use with the power system in the Traxxas Funny Car Race Replica (Model #6907).
Torque Control*
Seven Blinks Red
7
TSM
Eight Blinks Red
8
Press
SET