MODEL 58064-1 owner’s manual
INTRODUCTION 3 BEFORE YOU PROCEED 3 SAFETY PRECAUTIONS 5 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT 6 ANATOMY OF THE RAPTOR 7 QUICK START: GETTING UP TO SPEED 8 TRAXXAS TQ 2.4GHz RADIO SYSTEM 16 ADJUSTING THE ELECTRONIC SPEED CONTROL 18 DRIVING YOUR MODEL 20 ADJUSTING YOUR MODEL 22 MAINTAINING YOUR MODEL Thank you for purchasing the Ford F-150 SVT Raptor by Traxxas.
BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and examine the model carefully. If for some reason you decide it is not what you wanted, then do not continue any further. Your hobby dealer absolutely cannot accept a model for return or exchange after it has been run.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model. This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. No previous experience with radio controlled models is required. Models require a minimum of setup, maintenance, or support equipment.
TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Supplied Tools and Equipment 2.5mm “L” wrench 4-way wrench 2.0mm “L” wrench Antenna nut wrench Pre-load spacers and shock pistons 1.
ANATOMY OF THE RAPTOR Toe Link Front Shock Tower Battery Compartment Chassis Rear Shock Tower Front Camber Link Battery Hold-Down Electronic Speed Control Shock Steering Servo Slipper Clutch Spur Gear Pinion Gear Motor Transmission Antenna Mount Front Bumper Rear Bumper Receiver Box Front Suspension Arm Caster Block 6 • RAPTOR Rear Camber Link Rear Body Mount Steering Block Front Body Mount LED Light Pipe Half Shaft Rear Suspension Arm
QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on pages 3-4 For your own safety, understand where carelessness and misuse could lead to personal injury. 2. Charge the battery pack • See page 11 7. Check servo operation • See page 14 Make sure the steering servo is working correctly. 8.
TRAXXAS TQ 2.4GHz RADIO SYSTEM INTRODUCTION Applying the Decals The main decals for your model have been applied at the factory. Additional decals have been printed on selfadhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it from the backing. Your model includes the TQ 2.4GHz transmitter.
TRAXXAS TQ 2.4GHz RADIO SYSTEM Thermal Shutdown Protection - Temperature sensing electronics are used in the ESC to detect overloading and overheating of the transistor circuitry. If excessive temperature is detected, the unit automatically shuts down to prevent damage to the electronics. 2-channel radio system - The TQ 2.4GHz radio system, consisting of the receiver, the transmitter, and the servos. The system uses two channels: one to operate the throttle and one to operate the steering. 2.
TRAXXAS TQ 2.4GHz RADIO SYSTEM XL-5 Wiring Diagram Your model is equipped with the Traxxas TQ 2.4GHz transmitter. The transmitter has two channels: Channel one operates the steering, and channel two operates the throttle. The receiver inside the model has three output channels. Your model is equipped with one servo and an electronic speed control.
TRAXXAS TQ 2.4GHz RADIO SYSTEM INSTALLING TRANSMITTER BATTERIES CHARGING THE BATTERY PACK Your TQ 2.4GHz transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. The Traxxas Battery Charger is a fully featured NiMH (Nickle Metal Hydride) charger. It features 4-amp charge current for fast charging and advanced peak detection to optimize every charge.
TRAXXAS TQ 2.4GHz RADIO SYSTEM INSTALLING THE BATTERY PACK Battery iD Your model’s included battery pack is equipped with Traxxas Battery iD. This exclusive feature allows Traxxas battery chargers (sold separately) to automatically recognize connected battery packs and optimize the charge settings for the battery. This eliminates the need to worry over charger settings and menus for the easiest and safest charging solution possible. Visit Traxxas.
TRAXXAS TQ 2.4GHz RADIO SYSTEM RADIO SYSTEM CONTROLS Steering reversing procedure: 1. Press and hold the SET button on the transmitter for two seconds. The status LED will flash green. 2. Turn and hold the steering wheel to the full left or full right position (it does not matter which position you choose). 3. While holding the steering wheel in position, press the SET button to reverse the channel. 4. The channel is now reversed. Confirm correct servo operation before running your model.
TRAXXAS TQ 2.4GHz RADIO SYSTEM USING THE RADIO SYSTEM Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. 7,8 14 • RAPTOR The TQ 2.4GHz Radio System has been adjusted at the factory for correct operation with your model. The adjustment should be checked before running the model in case of movement during shipping. Here’s how: 1.
TRAXXAS TQ 2.4GHz RADIO SYSTEM their model at distances farther than a football field (300+ feet). At greater distances, you could lose sight of your model and you may also exceed the radio system’s operating range which will cause the fail-safe system to activate. For best visibility and control of your model keep your model within 200 feet, regardless of the maximum range available. No matter how fast or far you drive your model, always leave adequate space between you, the model, and others.
ADJUSTING THE ELECTRONIC SPEED CONTROL XL-5 Specifications Input Voltage 4-7 cells NiMH; 2S LiPo Case Size 1.23"W x 2.18"L x 0.75"H Weight 2.0 Ounces / 57 Grams Motor Limit 15-turns (540 Size) / 12-turns (550 Size) On Resistance Forward 0.005 Ohms On Resistance Reverse 0.014 Ohms Peak Current - Forward 100A Peak Current - Reverse 60A Braking Current 60A Continuous Current 15A BEC Voltage 6.
ADJUSTING THE ELECTRONIC SPEED CONTROL 8. The XL-5 is equipped with thermal shutdown protection to guard against overheating caused by excessive current flow. If the operating temperature exceeds safe limits, the XL-5 will automatically shut down. The LED on the face of the XL-5 will rapidly blink red, even if the throttle trigger is moved back and forth. Once the temperature returns to a safe level, the XL-5 will once again function normally.
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly important when using high-capacity (2400mAh and above) battery packs that allow extended periods of running. Monitoring temperatures will extend the lives of the batteries and motor.
DRIVING YOUR MODEL 2. The wheels have small holes molded in to allow air to enter and exit the tire during normal running. Water will enter these holes and get trapped inside the tires if holes are not cut in the tires. Cut two small holes (3mm or 1/8” diameter) in each tire. Each hole should be near the tire centerline, 180 degrees apart. 3. Confirm that the receiver box O-ring and cover are installed correctly and secure.
-1° -1° -1.5° -1.5° ADJUSTING YOUR MODEL All of the toe links are installed on the truck so the left-hand thread indicators point to the same direction. This makes it easier to remember which way to turn the wrench to increase or decrease toe link length (the direction is the same at all four corners). Note that the groove in the hex indicates the side of the toe link with the left-hand threads.
ADJUSTING YOUR MODEL Motor and Gearing There are two different types of aftermarket motors that can be purchased for your model, stock and modified. Stock motors all have the same wire thickness and number of turns around the armature as governed by sanctioned racing organizations. They are inexpensive and widely available. Modified motors are more expensive, may feature ball bearings, and come in a variety of wire thicknesses and a number of turns of wire on the armature.
MAINTAINING YOUR MODEL Always wear eye protection when using compressed air or spray cleaners and lubricants. Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Inspect the vehicle for obvious damage or wear. Look for: 1. Cracked, bent, or damaged parts 2. Check the wheels and steering for binding. 3. Check the operation of the shock absorbers. 4. Check the wiring for any frayed wires or loose connections. 5.
MODEL 58064-1 owner’s manual 6200 TRAXXAS WAY, McKINNEY, TEXAS 75070 1-888-TRAXXAS 141007 58064-1-OM-EN-R00
