Installation Manual

Note: Expander mounts are available for most vehicles to make installation of the Telemetry Expander
easier and more secure. Visit Traxxas.com or contact your local hobby dealer to obtain the correct
Expander mount for your particular vehicle.
Kit Contents
Telemetry Expander (1)
Communication cable (425mm) (1)
3x10mm cap screws (2)
Silicone grease (Traxxas part #1647) (1)
Zip tie (1)
Note: Remove the wire clamp and the receiver cover on
your model to gain access to the receiver.
A. Install the Expander on a previously installed
Expander mount (not included) with the included
3x10mm cap screws (2).
B. Remove the front cover from the Expander.
C. Plug the communication cable and desired sensors
into the Expander.
Note: Before sealing the covers on the Expander and
receiver, make sure all smart sensors for Telemetry
expansion have been installed and are operating
properly. Ensure that the blue O-ring is properly seated
in the groove around the receiver box. Refer to the
vehicle Owner’s Manual for detailed instructions on
maintaining a watertight seal.
D. Apply a small bead of silicone grease to the foam
on the Expander and the top of the foam insert.
E. Route the communication cable and the smart sensor cable(s) over and/or between
the foam inserts on the Expander.
F. Replace the Expander cover, and reinstall the 3x10mm cap screws (2).
G. Power up the system and verify that all sensors have linked, indicated by a solid green
LED on the Expander. If the LED is blinking red, there is an error in the system. Visit
Traxxas.com/telemetry for complete information and instructions on compatible
devices and using the Traxxas Link™ App and the Telemetry Expander to capture and
display real-time Telemetry, such as voltage and temperature.
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: [phone], Fax: [phone], e-mail: [e-mail]
Covers Part #6550
Telemetry Expander Installation Instructions
If you have questions or need technical assistance, call Traxxas at
1-888-TRAXXAS
(1-888-872-9927) (U.S. residents only)
KC1784-R02 160408
D
F
E
Note: Traxxas models may have some Telemetry-ready parts installed from the factory.
Please inspect the model before installation.
Required for Telemetry GPS operation:
• TQi radio system with Traxxas Link™ Wireless Module (part #6511)
• Traxxas Link receiver (part #6533)
• Apple® iOS or Android™ mobile device (visit Traxxas.com for a list of current
compatible devices)
• Traxxas Link App (latest version available free from the Apple® App Store
SM
or on
Google Play™)
Communication
cable*
To Sensor
Wiring Diagram
Receiver
Expander
Apply silicone
grease
3x10CS
3x10CS
Included
3x10CS
Expander
Mount Post
(Expander Mount
Sold Separately)
3x10CS
3x10CS
Included
3x10CS
Expander
Mount Post
(Expander Mount
Sold Separately)
3x10CS
3x10CS
Included
3x10CS
Expander
Mount Post
(Expander Mount
Sold Separately)
Plug communication
cable here
Use any of these six
ports for connecting
smart sensors
A B
C
Expansion
port
This device complies with FCC Part-15 & IC RSS-210 rules subject to the following conditions: 1)This device may not cause harmful interference, and 2)This device must accept all interference received, including interference that may cause undesired operation.
*Use the included zip tie to coil and secure any excess length of the communication
cable. Ensure the communication cable is kept away from any moving parts and
heated surfaces.
Apple, the Apple logo, iPhone, iPad, iPod touch, and iTunes are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Android and Google Play are trademarks of Google Inc.