MODEL 71054-1 owner’s manual
INTRODUCTION 3 BEFORE YOU PROCEED 4 SAFETY PRECAUTIONS 7 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT 8 ANATOMY OF THE 1/16 E-REVO 9 QUICK START: GETTING UP TO SPEED 10 THE TRAXXAS TQ 2.4GHz RADIO SYSTEM 18 ADJUSTING THE ELECTRONIC SPEED CONTROL 20 DRIVING YOUR MODEL 23 TUNING ADJUSTMENTS 27 MAINTAINING YOUR MODEL Thank you for purchasing a Traxxas 1/16 scale model.
BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and examine the model carefully. If for some reason you decide it is not what you wanted, then do not continue any further. Your hobby dealer absolutely cannot accept a model for return or exchange after it has been run.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model. This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. No previous experience with radio controlled models is required. Models require a minimum of setup, maintenance, or support equipment. 4 • 1/16 E-REVO All of us at Traxxas want you to safely enjoy your new model.
SAFETY PRECAUTIONS WARNING! CAUTION! DANGER! FIRE HAZARD! Your model is able to use LiPo batteries. Charging and discharging batteries has the potential for fire, explosion, serious injury, and property damage if not performed per the instructions. Before use, read and follow all manufacturer’s instructions, warnings, and precautions.
SAFETY PRECAUTIONS (continued from previous page) • DO NOT charge batteries inside of an automobile. DO NOT charge batteries while driving in an automobile. This charger is equipped with a long cord intended to allow the battery to be charged outside of an automobile when using the automobile’s auxiliary power socket. If the cord will not reach outside of the automobile, find another power source. • NEVER charge batteries on wood, cloth, carpet, or on any other flammable material.
TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. SUPPLIED TOOLS AND EQUIPMENT REQUIRED EQUIPMENT (sold separately) 4 AA alkaline batteries 1.5mm “L” wrench 2.0mm “T” wrench 2.5mm ball driver wrench 4-way wrench For more information on batteries, see Use the Right Batteries on page 13.
ANATOMY OF THE 1/16 E-REVO Rear Half Shaft Battery Compartment Vent Hex Hub Battery Door Release Tab Toe Link Antenna Mount Rear Body Mount Battery Compartment Door Wing Pivot Ball Axle Carrier Light Pipe Receiver Box Steering Link Push Rod Rocker Front Bumper Front Body Mount Electronic Speed Control (XL-2.
QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on page 4-6 For your own safety, understand where carelessness and misuse could lead to personal injury. 2. Install batteries in the transmitter • See page 13 The transmitter requires 4 AA alkaline or rechargeable batteries (sold separately). 3.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM INTRODUCTION Your model includes the TQ 2.4GHz transmitter. When powered on, the TQ 2.4GHz will automatically locate and lock onto an available frequency, allowing multiple models to be raced together without frequency conflicts. Just switch on and drive! The included TQ 2.4GHz radio system has been programmed for your model at the factory and does not require adjustment, but it does have settings you may need to access to maintain proper operation of your model.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM Transmitter - The hand-held radio unit that sends throttle and steering instructions to your model. Trim - The fine-tuning adjustment of the neutral position of the servos, made by adjusting the steering trim knob on the face of the transmitter. Thermal Shutdown Protection - Temperature sensing electronics used in the electronic speed control detect overloading and overheating of the transistor circuitry.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM XL-2.5 Wiring Diagram Your model is equipped with the Traxxas TQ 2.4GHz transmitter. The transmitter has two channels: Channel one operates the steering, and channel two operates the throttle. The receiver inside the model has three output channels. Your model is equipped with one servo and an electronic speed control.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM INSTALLING TRANSMITTER BATTERIES CHARGING THE BATTERY PACK Your TQ 2.4GHz transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. The Traxxas Battery Charger is a fully featured NiMH (Nickle Metal Hydride) charger. It features 2-amp charge current for fast charging and advanced peak detection to optimize every charge.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM INSTALLING THE RECEIVER ANTENNA To prevent loss of radio range, do not kink or cut the black wire, do not bend or cut the metal tip, and do not bend or cut the white wire at the end of the metal tip. Correct No No No No Battery iD Your model’s included battery pack is equipped with Traxxas Battery iD.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM RADIO SYSTEM CONTROLS RADIO SYSTEM BASIC ADJUSTMENTS Steering Trim The steering trim knob located on the face of the transmitter adjusts the neutral (center) point of the steering channel. If your model pulls to the right or left when the steering wheel is centered, turn the knob until the model drives straight when the steering wheel is centered. TUR N GH RI T TU RN LE FT Channel Reversing The TQ 2.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM USING THE RADIO SYSTEM Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. The TQ 2.4GHz Radio System has been adjusted at the factory for correct operation with your model. The adjustment should be checked before running the model, in case of movement during shipping. Here’s how: 1. Turn the transmitter switch on.
THE TRAXXAS TQ 2.4GHz RADIO SYSTEM Higher Speeds Require Greater Distance The faster you drive your model, the more quickly it will near the limit of radio range. At top speeds, models can cover anywhere between 50 to 100 feet every second! It’s a thrill, but use caution to keep your model in range. If you want to see your model achieve its maximum speed, it is best to position yourself in the middle of the truck’s running area, not the far end, so you drive the truck towards and past your position.
ADJUSTING THE ELECTRONIC SPEED CONTROL XL-2.5 ESC Specifications Input Voltage: 4-7 Cells (4.8V - 8.4V DC) 2S LiPo Case Size (W x D x H): 26.5 x 46.5 x 22mm Weight: 33 Grams Motor Limit*: 10-Turns (380 Size), 12-Turns (550 Size) On-Resistance (@Trans): 0.008 Ohms Reverse Delay: None BEC Voltage: 6.
ADJUSTING THE ELECTRONIC SPEED CONTROL 7. To turn the XL-2.5 off, press and hold the EZ-Set button for 1½ seconds or until the red LED turns off. 8. The XL-2.5 is equipped with thermal shutdown protection to guard against overheating caused by excessive current flow. If the operating temperature exceeds safe limits, the XL-2.5 will automatically shut down. The LED on the face of the XL-2.5 will rapidly blink red, even if the throttle trigger is moved back and forth.
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. run time is how the model is driven. Run times may decrease when the model is driven repetitively from a stop to top-speed and with repetitive hard acceleration. • Allow the model to cool for a few minutes between runs.
DRIVING YOUR MODEL • Not all batteries can be used in wet environments. Consult your battery manufacturer to see if their batteries can be used in wet conditions. • The Traxxas TQ 2.4GHz transmitter is not water resistant. Do not subject it to wet conditions such as rain. • Do NOT operate your model during a rain storm or other inclement weather where lightning may be present.
DRIVING YOUR MODEL 9. Additional Maintenance: Increase your frequency of disassembly, inspection and lubrication of the following items. This is necessary after extended wet use or if the vehicle will not be used for an extended period of time (such as a week or longer). This additional maintenance is needed to prevent any trapped moisture from corroding internal steel components. • Stub axle housing bearings: Remove, clean, and re-oil the bearings.
TUNING ADJUSTMENTS Your model is factory-tuned for optimum performance in a wide variety of off-road conditions. To tailor the performance and handling of your model to suit your driving style and terrain, the model has a number of adjustable features. Gearing, shock preload and damping, ride height and wheel camber can all be easily adjusted. SUSPENSION TUNING Total Travel Ride Height Adjustment Your model has threaded shock bodies that make it easy to adjust ride height.
TUNING ADJUSTMENTS A camber gauge (available at your local hobby shop) can be a useful tool for alignment setting. To achieve a good starting point for the slipper clutch, tighten the slipper clutch adjusting nut clockwise until the slipper clutch adjusting spring fully collapses (do not over tighten), and then turn the slipper clutch nut counterclockwise ¾ to 1 turn. Static Camber Adjustment The wheels can be set to have either positive or negative camber (see illustration below).
TUNING ADJUSTMENTS From the factory, both the differentials are filled with SAE 30,000W viscosity silicone oil. Only use silicone oil in the differentials. Traxxas sells SAE 10,000W and SAE 50,000W viscosity oil (see your parts list). The differentials have to be removed from the vehicle and disassembled to change/replace oil. MOTOR AND GEARING Extensive testing has been done to determine the best gear ratios for the 1/16 E-Revo.
TUNING ADJUSTMENTS Adjusting Gear Mesh Incorrect gear mesh is the most common cause of stripped spur gears. Gear mesh should be checked and adjusted anytime a gear is replaced. Access the gears by removing the single screw on the top gear cover. To set the gear mesh, cut a narrow strip of notebook paper and run it into the gear mesh of the motor. The motor is mounted to an aluminum motor mount. Loosen the single motor mount screw with the provided 2.5mm wrench to slide the motor mount.
MAINTAINING YOUR MODEL Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Inspect the vehicle for obvious damage or wear. Look for: 1. Cracked, bent, or damaged parts 2. Check the wheels and steering for binding. 3. Check the operation of the shock absorbers. 4. Check the wiring for any frayed wires or loose connections. 5. Check the mounting of the receiver and servo(s) and speed control. 6.
owner’s manual MODEL 71054-1 6250 TRAXXAS WAY, MCKINNEY, TEXAS 75070 1-888-TRAXXAS 190603 71054-1-OM-EN-R02
