MODEL 82034-4 EQUIPPED WITH owner’s manual
introduction 3 BEFORE YOU PROCEED 4 SAFETY PRECAUTIONS 7 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT 8 ANATOMY OF THE TRX-4 10 QUICK START: GETTING UP TO SPEED 11 THE TRAXXAS TQ 2.4GHz RADIO SYSTEM 19 ADJUSTING THE ELECTRONIC SPEED CONTROL 22 DRIVING YOUR MODEL 25 ADJUSTING YOUR MODEL 30 MAINTAINING YOUR MODEL Thank you for purchasing the Traxxas TRX-4® equipped with All-Terrain Traxx™.
before you proceed Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. SUPPORT Before running your model, look over this entire manual and examine the model carefully. If for some reason you decide it is not what you wanted, then do not continue any further. Your hobby dealer absolutely cannot accept a model for return or exchange after it has been run.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model. This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. No previous experience with radio controlled models is required. Models require a minimum of setup, maintenance, or support equipment. 1 4 • TRX-4 All of us at Traxxas want you to safely enjoy your new model.
SAFETY PRECAUTIONS WARNING! CAUTION! DANGER! FIRE HAZARD! Your model is able to use LiPo batteries. Charging and discharging batteries has the potential for fire, explosion, serious injury, and property damage if not performed per the instructions. Before use, read and follow all manufacturer’s instructions, warnings, and precautions.
SAFETY PRECAUTIONS (continued from previous page) • REMOVE flammable items and combustible materials from the charging area. • DO NOT leave the charger and battery unattended while charging, discharging, or anytime the charger is ON with a battery connected. If there are any signs of a malfunction or in the event of an emergency, unplug the charger from the power source and disconnect the battery from the charger.
tools, supplies, and required equipment Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Supplied Tools and Equipment 2.0mm “T” wrench 2.5mm “L” wrench 1.
ANATOMY OF THE TRX-4 Chassis Top View Battery Hold-Down Battery Compartment Traxxas High-Current Connector Electronic Speed Control LED Lighting Module Slipper Clutch Transmission Motor Front Body Mount Front Bumper Rear Body Mount Rear Bumper Antenna Mount Chassis Rail 8 • SUMMIT Rock Slider LED Light Pipe Receiver Box Steering Servo
ANATOMY OF THE TRX-4 Chassis Bottom View Rear Axle Chassis Rail Differential Cover Rear Portal Housing Rear Upper Link Shock Rear Lower Link Rear Driveshaft Floor Pan Front Upper Link Front Portal Housing Front Axle Skidplate Front Driveshaft Front Lower Link Caster Block
quick start: getting up to speed The Quick Start Guide is not intended to replace the full operating instructions available in this manual. Please read this entire manual for complete instructions on the proper use and maintenance of your model. The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1.
TRAXXAS TQi RADIO SYSTEM INTRODUCTION Your model includes the TQ 2.4GHz transmitter. When powered on, the TQ 2.4GHz will automatically locate and lock onto an available frequency, allowing multiple models to be raced together without frequency conflicts. Just switch on and drive! The included TQ 2.4GHz radio system has been programmed for your model at the factory and does not require adjustment, but it does have settings you may need to access to maintain proper operation of your model.
TRAXXAS TQ 2.4GHz RADIO SYSTEM To prevent loss of radio range, do not kink or cut the black wire, do not bend or cut the metal tip, and do not bend or cut the white wire at the end of the metal tip. Thermal Shutdown Protection - Temperature sensing electronics are used in the ESC to detect overloading and overheating of the transistor circuitry. If excessive temperature is detected, the unit automatically shuts down to prevent damage to the electronics. 2-channel radio system - The TQ 2.
TRAXXAS TQ 2.4GHz RADIO SYSTEM Your model is equipped with the Traxxas TQ 2.4GHz transmitter. The transmitter has two channels: Channel one operates the steering, and channel two operates the throttle. The receiver inside the model has three output channels. Your model is equipped with one servo and an electronic speed control.
TRAXXAS TQ 2.4GHz RADIO SYSTEM INSTALLING TRANSMITTER BATTERIES If the status LED doesn’t light green, check the polarity of the batteries. Check rechargeable batteries for a full charge. If you see any other flashing signal from the LED, refer to the chart on page 18 to identify the code. Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter.
TRAXXAS TQ 2.4GHz RADIO SYSTEM INSTALLING THE BATTERY PACK WARNING: Do not pinch the battery wires or connector. Install the battery pack with the battery wires facing the rear of the model. Swing the battery hold down towards the chassis and snap (lock) the end into the front hold-down retainer. Note: The battery hold down can be rotated on its pivot to accommodate different height battery packs. The Traxxas High-Current Connector Your model is equipped with the Traxxas High-Current Connector.
TRAXXAS TQ 2.4GHz RADIO SYSTEM RADIO SYSTEM CONTROLS Remember, always turn the transmitter on first and off last to avoid damage to your model. • In order for the transmitter and receiver to bind to one another, the receiver in the model must be turned on within 20 seconds of turning on the transmitter. The transmitter LED will flash fast red, indicating a failure to link. If you miss it, simply turn off the transmitter and start over.
TRAXXAS TQ 2.4GHz RADIO SYSTEM 1. Press and hold the SET button on the transmitter for two seconds. The status LED will flash green. 2. Move and hold the throttle trigger to the full forward or full brake position (it does not matter which position you choose). 3. While holding the throttle trigger in position, press the SET button to reverse the channel. 4. The channel is now reversed. Recalibrate the speed control and then confirm correct servo operation before running your model.
TRAXXAS TQ 2.4GHz RADIO SYSTEM Fail-Safe Your Traxxas radio system is equipped with a builtin fail-safe function that returns the throttle to its last saved neutral position in the event of a signal loss. The LED on the transmitter and the receiver will rapidly flash red when the failsafe mode is activated. If fail-safe activates while you are operating your model, determine the reason for signal loss and resolve the problem before operating your model again.
ADJUSTING THE ELECTRONIC SPEED CONTROL XL-5 HV Battery Settings (Low-Voltage Detection Setting) The XL-5 HV electronic speed control is equipped with built-in LowVoltage Detection. The Low-Voltage Detection circuitry constantly monitors the battery voltage. When the battery voltage begins to reach the minimum recommended discharge voltage threshold for LiPo battery packs, the XL-5 HV will limit the power output to 50% throttle.
ADJUSTING THE ELECTRONIC SPEED CONTROL Patented Training Mode (Profile #3) reduces forward and reverse throttle by 50%. Training Mode is provided to reduce the power output, allowing beginning drivers to better control the model. As driving skills improve, simply change to Sport, Race, Trail, or Crawl Mode for full-power operation. 2. 3. 4. 5. 6. Tip For Fast Mode Changes The XL-5 HV is set to Profile 4 (Trail Mode) as the default.
ADJUSTING THE ELECTRONIC SPEED CONTROL Selecting Trail Mode (Profile #4: 100% Forward, 100% Brakes, 100% Reverse; A B Drag Brake at Neutral) 1. Connect a fully charged battery pack to the XL-5 HV and turn on your transmitter. Green to Red to Off Four blinks Red 2. With the XL-5 HV off, press and hold D C the EZ-Set button until the LED turns solid green, then solid red and then begins blinking red (indicating the Release Solid Profile numbers). 3.
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. CAUTION: The stock gearing (11-T pinion and 45-T spur gear) is suitable for general use in most terrain with NiMH or 2s/3s LiPo batteries. If you decide to modify the gear ratio, use caution to avoid damage to your vehicle’s electronics (see the “Motors and Gearing” section on page 27).
DRIVING YOUR MODEL Tips for Increasing Run Time • Use batteries with the highest mAh rating you can purchase. • Use a high-quality peak-detecting charger. • Read and follow all maintenance and care instructions provided by the manufacturer of your batteries and charger. • Keep the XL-5 HV cool. Get plenty of airflow across the ESC heat sink. • Lower your gear ratio.
DRIVING YOUR MODEL 6. Placing the truck in a warm, sunny spot will aid drying. Trapped water and oil will continue to drip from the truck for a few hours. Place it on a towel or piece of cardboard to protect the surface underneath. 7. As a precautionary step, remove the sealed receiver box cover. While unlikely, humidity or tiny amounts of moisture or condensation may enter the receiver box during wet running. This can cause long-term problems with the sensitive electronics in the receiver.
ADJUSTING YOUR MODEL Adjustment procedures for alignment, spring rate, damping, steering, and ride height are covered here. SUSPENSION TUNING Springs TRX-4’s front springs (0.30 rate, white stripe) and rear springs (0.54 rate, green stripe) have been carefully selected to provide full suspension articulation and support for the weight of the vehicle body.
ADJUSTING YOUR MODEL Never slide the threads on the shock rod past the X-ring seals when it is installed and compressed by the bottom cap of the shock. Doing so will damage the seal and cause shock oil to leak. Shock assembly 1. Insert the shock shaft assembly through the shock body until the piston bottoms out. 2. Lubricate the shaft, O-ring, and X-rings with silicone oil. 3. Install the O-ring, X-rings and spacer over the shaft and into the bore of the shock body. 4. Install the lower cap. 5.
ADJUSTING YOUR MODEL C Many types of aftermarket tires and wheels can be adapted for use on your model. Most will affect the overall width and the suspension geometry of the model. The offsets and dimensions designed into TRX-4 wheels are intentional; therefore, Traxxas cannot recommend the use of other non-Traxxas wheels with different specifications. Minimum Wheel When selecting wheels, the inner Inner Diameter diameter of the inside of the wheels must be 38mm or larger to accommodate the axle portals.
ADJUSTING YOUR MODEL Use the following formula to calculate the overall ratio for combinations not listed on the gear chart: # Spur Gear Teeth # Pinion Gear Teeth x 15.8 = Final Gear Ratio CAUTION: The stock gearing (11-T pinion and 45-T spur gear) is suitable for general use in most terrain with NiMH or 2s/3s LiPo batteries. If you decide to modify the gear ratio, use caution to avoid damage to your vehicle’s electronics.
ADJUSTING YOUR MODEL If you are using aftermarket servos, it is important to use servo horns designed for TRX-4. The servo horns must measure 22mm from the steering linkage mounting hole to the servo mounting hole. FITTING AFTERMARKET BODIES Rear Shock Tower The rear shock tower can be installed in two different locations and in two orientations each. This is to allow precise angle adjustment of the rear shocks.
MAINTAINING YOUR MODEL Always wear eye protection when using compressed air or spray cleaners and lubricants. Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Inspect the vehicle for obvious damage or wear. Look for: 1. Cracked, bent, or damaged parts 2. Check the tracks and steering for binding. 3. Check the operation of the shock absorbers. 4. Check the wiring for any frayed wires or loose connections. 5.
EQUIPPED WITH owner’s manual MODEL 82034-4 6250 Traxxas Way McKinney, Texas 75070 1-888-TRAXXAS 190614 82034-4-OM-EN-R00