User Manual

12
•
SLAYER PRO 4X4
USING THE TQ 2.4GHz RADIO SYSTEM
The TQ 2.4GHz Radio System has been pre-adjusted at the factory.
The adjustment should be checked before running the model, in
case of movement during shipping. Here’s how:
1. Turn the transmitter switch on. The status LED on the transmitter
should be solid green (not flashing).
2. Turn on the receiver switch in the model. The switch is located on
the rear shock tower.
3.
Position the Slayer Pro 4x4 so that its front wheels are off the ground.
4. Turn the steering wheel on the transmitter back and forth and
check for rapid operation of the steering servo. Also, check that
the steering mechanism is not loose or binding. If the steering
operates slowly, check for weak receiver batteries.
5. When looking down at model, the
front wheels should be pointing
straight ahead. If the wheels are
turned slightly to the left or right,
slowly adjust the steering trim
control on the transmitter until they
are pointing straight ahead.
6. Operate the throttle trigger on the transmitter and check for
rapid operation of the throttle servo. When the throttle trigger
is pulled back, the carburetor should open. When the throttle
trigger is pushed all the way forward, the brake should lock.
7. Once adjustments are made, turn off the receiver on your model,
followed by the hand-held transmitter.
Range-Testing the Radio System
Before each running session with your model, you should range-test
your radio system to ensure that it operates properly.
1. Turn on the radio system and check its operation as described in
the previous section.
2. Have a friend hold the model with the engine off.
3. Make sure your transmitter antenna is straight up, and then walk
away from the model with the transmitter until you reach the
farthest distance you plan to operate the model.
4. Operate the controls on the transmitter once again to be sure
that the model responds correctly.
5. Do not attempt to operate the model if there is any problem with
the radio system or any external interference with your radio
signal at your location.
Higher Speeds Require Greater Distance
The faster you drive your model, the more quickly it will near the
limit of radio range. At 60mph, a model can cover 88 feet every
second! It’s a thrill, but use caution to keep your model in range.
If you want to see your model achieve its maximum speed, it
is best to position yourself in the middle of the truck’s running
area, not the far end, so you drive the truck towards and past
your position. In addition to maximizing the radio’s range, this
technique will keep your model closer to you, making it easier to
see and control.
No matter how fast or far you drive your model, always leave
adequate space between you, the model, and others. Never
drive directly toward yourself or others.
TQ 2.4GHz Binding Instructions
For proper operation, the transmitter and receiver must be
electronically ‘bound.’ This has been done for you at the factory.
Should you ever need to re-bind the system or bind to an additional
transmitter or receiver, follow these instructions. Note: the receiver
must be connected to a 4.8-6.0v (nominal) power source for binding
and the transmitter and receiver must be within 5 feet of each other.
1. Press and hold the transmitter’s SET button as you switch
transmitter on. The transmitter’s LED will flash red slowly.
Release the SET button
2.
Press and hold the receiver’s LINK button as you switch on the model.
Release the LINK button.
3. When the transmitter and receiver’s LEDs turn solid green, the
system is bound and ready for use. Confirm that the steering and
throttle operate properly before driving your model.
Steering Sensitivity (Exponential)
The Multi-Function knob on the TQ2.4GHz transmitter has
been programmed to control Steering Sensitivity (also known
as exponential). The standard setting for Steering Sensitivity is
“normal (zero exponential),” with the dial full left in its range of
travel. This setting provides linear servo response: the steering
servo’s movement will correspond exactly with the input from the
transmitter’s steering wheel. Turning the knob clockwise from center
will result in “negative exponential” and decrease steering sensitivity
by making the servo less responsive near neutral, with increasing
sensitivity as the servo nears the limits of its travel range. The farther
When the engine is running,
do not use the throttle trim
on the transmitter to adjust
the engine idle speed.
Always use the idle speed
adjustment screw (see page
15) on the carburetor.
Applying The Decals
The main decals for your model
have been applied at the factory.
The decals are printed on self-
adhesive clear mylar and are
die-cut for easy removal. Use a
hobby knife to lift the corner of a
decal and lift it from the backing.
To apply the decals, place one
end down, hold the other end up,
and gradually smooth the decal
down with your nger as you
go. This will prevent air bubbles.
Placing both ends of the decal
down and then trying to smooth
it out will result in air pockets.
TRAXXAS TQ 2.4GHZ RADIO SYSTEM
4,8,9
0
°
0
°
0
°
0
°