TRA85086-4 Unlimited Desert Racer Manual
DESERT RACER
•
21
ADJUSTING THE ELECTRONIC SPEED CONTROL
Patented Training Mode
(Profile #3) reduces forward
and reverse throttle by 50%.
Training Mode is provided
to reduce the power output,
allowing beginning drivers
to better control the model.
As driving skills improve,
simply change to Sport or
Race Mode for full-power
operation.
The VXL-6s has built-in
programming that prevents
accidental activation of
reverse while in forward
motion and vice-versa. You
must come to a complete
stop, release the throttle
trigger, then apply opposite
throttle to engage the motor
in the desired direction.
Selecting Sport Mode
(Profile #1: 100% Forward, 100% Brakes, 100% Reverse)
1. Connect two fully charged battery
packs to the VXL-6s and turn on your
transmitter.
2. Press and hold the EZ-Set button until the
LED turns solid green, then solid red and
then begins blinking red (indicating the
Profile numbers).
3. When the LED blinks red once, release
the EZ-Set button.
4. The LED will blink and then turn solid green. The model is ready to
drive.
Selecting Race Mode
(Profile #2: 100% Forward, 100% Brakes, No Reverse)
1. Connect two fully charged battery
packs to the VXL-6s and turn on your
transmitter.
2. Press and hold the EZ-Set button until the
LED turns solid green, then solid red and
then begins blinking red (indicating the
Profile numbers).
3. When the LED blinks red twice, release
the EZ-Set button.
4. The LED will blink and then turn solid green. The model is ready to
drive.
Selecting Training Mode
(Profile #3: 50% Forward, 100% Brakes, 50% Reverse)
1. Connect two fully charged battery
packs to the VXL-6s and turn on your
transmitter.
2. Press and hold the EZ-Set button until the
LED turns solid green, then solid red and
then begins blinking red (indicating the
Profile numbers).
3. When the LED blinks red three times,
release the EZ-Set button.
4. The LED will blink and then turn solid green. The model is ready to
drive.
Note: If you missed the mode you wanted, keep the EZ-Set button
pressed down and the blink cycle will repeat until the button is
released and a mode is selected.
Accessory Power Panel
The VXL-6s electronic speed control is equipped with a power panel
that can be used to power optional accessories, such as LED light kits
or additional cooling fans (see Traxxas.com for additional information).
Always be sure to keep the panel cover installed when
accessories are not being used to protect the pins
from damage.
LED Codes and Protection Modes
The VXL-6s electronic speed control is equipped
with sophisticated circuitry designed to help protect
the electronics from damage caused by overloading and excessive
temperatures. When a protection circuit is activated, an LED on the VXL-
6s ESC will light, indicating a fault.
Explanation Solution
Overcurrent
Protection,
Stage 1
Stop driving; inspect the vehicle for
overgearing or damage.
Overcurrent
Protection,
Stage 2
Stop driving; inspect the vehicle for
overgearing or damage.
Low Voltage
Protection,
Stage 1
Stop driving; inspect the batteries
and recharge.
Low Voltage
Protection,
Stage 2
Stop driving; inspect the batteries
and recharge.
Overvoltage
Stop driving and disconnect the
batteries. Inspect the batteries and
confirm the battery voltage.
Thermal
Shutdown
Protection,
Stage 1
Stop driving; inspect the cooling fan
on the ESC. Allow the power system
to cool before continuing.
Thermal
Shutdown
Protection,
Stage 2
Stop driving; inspect the cooling fan
on the ESC. Allow the power system
to cool before continuing.
Critical
functioning
error
Contact Traxxas Customer Service.
Programming
error
Contact Traxxas Customer Service.
A V
A V
A V
A V
B
Two blinks Red
A
Green to Red to Off
D
Solid
C
Release
B
Three blinks Red
A
Green to Red to Off
D
Solid
C
Release
B
One blink Red
A
Green to Red to Off
D
Solid
C
Release