MODEL 6407X OWNER’S MANUAL
INTRODUCTION TABLE OF CONTENTS 3 SAFETY PRECAUTIONS 6 BEFORE YOU PROCEED 7 TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT 8 ANATOMY OF THE XO-1 9 QUICK START: GETTING UP TO SPEED 10 TRAXXAS TQi RADIO SYSTEM 18 ADJUSTING THE ELECTRONIC SPEED CONTROL 19 DRIVING YOUR MODEL 20 BASIC TUNING ADJUSTMENTS Thank you for purchasing the XO-1.
SAFETY PRECAUTIONS WARNING! RISK OF FIRE, INJURY, OR DEATH Experts Only! This product is not a toy. This product carries our highest skill level rating, 10, and is not intended for use by children or minors under the age of 16. Individuals under the age of 18 require responsible adult supervision during operation and maintenance. The XO-1 is only intended to be owned and operated by experienced users, with advanced skills, and expert driving ability.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe For Expert Drivers operation of your model. For Expert Drivers ONLY All of us at Traxxas want you to safely enjoy your new model. The precautions outlined in this manual should be strictly followed to help ensure safe operation. You alone must see that the instructions are followed and the precautions are adhered to. The XO-1 is optimized for use with LiPo batteries.
SAFETY PRECAUTIONS WARNING! CAUTION! DANGER! FIRE HAZARD! Before use, read and follow all manufacturer’s charging and handling instructions, warnings and precautions! Lithium Polymer batteries pose a severe risk of fire if not properly handled and charged per the manufacturer’s instructions. Never allow children under the age of 14 to charge batteries without the supervision of a responsible, knowledgeable adult.
BEFORE YOU PROCEED The XO-1 features a Castle Creations Brushless System preinstalled from the factory. The XO-1 is manufactured by Traxxas and is backed by full Traxxas factory support. The installed Mamba Monster Extreme power system (electronic speed control, motor, on/off switch) is manufactured by Castle Creations. Traxxas will direct warranty claims and related support for the power system directly to Castle Creations and those claims will be subject to Castle Creations’ warranty and service terms.
TOOLS, SUPPLIES, AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. SUPPLIED TOOLS AND EQUIPMENT * Skill Level = Myriad Semi Bold Shock wrench Suspension multi-tool 4-way wrench 17mm wheel wrench 8mm/4mm wrench 1.5mm “L” wrench 2.0mm “T” wrench bluehighway font 2.5mm ball driver 1 2 3 3+ 4 5 2.
ANATOMY OF THE XO-1 Shock (Oil Damper) Half Shaft Rear Body Mount Front Suspension Arm Drive Shaft Chassis Brace Electronic Speed Control Turnbuckle (Front Camber Link) Receiver Box LED Light Pipe Front Body Mount Antenna Mount Diffuser Turnbuckle (Rear Camber Link) Temperature Sensor Motor Rear Shock Tower Motor Mount Rear Suspension Arm Spur Gear 8 • XO-1 Battery Hold-Down Traxxas High-Current Connector Cooling Duct Steering Servo Turnbuckle (Toe Link) Half Shaft Front Shock Tower Foam Bum
QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions beginning on page 3 For your own safety, understand where carelessness and misuse could lead to property damage, fire, personal injury, or death. Safety is your responsibility. 2. Charge two battery packs • See page 13 6.
TRAXXAS TQi RADIO SYSTEM INTRODUCTION Applying the Decals The main decals for your model have been applied at the factory. The decals are printed on self-adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it from the backing. Your model includes the latest Traxxas TQi 2.4GHz transmitter with Traxxas Link™ Model Memory.
TRAXXAS TQi RADIO SYSTEM Neutral position - The standing position that the servos seek when the transmitter controls are at the neutral setting. NiMH - Abbreviation for nickel-metal hydride, the most common radio-control battery type. NiMH packs have lower current handling ability and less capacity than LiPo packs, but are generally lower in cost and provide reliable performance. Receiver - The radio unit inside your model that receives signals from the transmitter and relays them to the servos.
TRAXXAS TQi RADIO SYSTEM Castle Creations Motor Specifications Type: 1717 Sensorless brushless RPM/volt (kV): 1650 Magnet type: Ultra High-Temperature Sintered Neodymium Connection type : 6.5mm bullet Wire size: 10 Gauge Max RPM: 45,000 Diameter: 50mm (1.97") Length: 85mm (3.35") Weight: 594g (20.96oz) Your model is equipped with the newest TQi 2.4GHz transmitter with Traxxas Link™ Model Memory. The transmitter has two channels for controlling your throttle and steering.
TRAXXAS TQi RADIO SYSTEM INSTALLING TRANSMITTER BATTERIES Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. 1. Remove the battery compartment door by pressing the tab and sliding the door open. 2. Remove the battery holder. Install the batteries in the battery holder. Correct orientation is indicated in the battery holder. Make sure the battery holder is plugged into the transmitter. 3. Reinstall the battery holder. 4.
TRAXXAS TQi RADIO SYSTEM INSTALLING & REMOVING THE BATTERY PACKS Installing the Battery Packs The following Traxxas High Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector. Part #3060 Single Male/Female Part #3061 Male Charge Adapter Part #3080 2-Pack Female Part #3070 2-Pack Male 1. Insert the battery into the tray with the High Current Connector positioned towards the rear of the car. 2.
TRAXXAS TQi RADIO SYSTEM RADIO SYSTEM CONTROLS • In order for the transmitter and receiver to bind to one another, the receiver in the model must be turned on within 20 seconds of turning on the transmitter. The transmitter LED will flash fast red indicating a failure to link. If you miss it, simply turn off the transmitter and start over. Remember, always turn the TQi transmitter on first and off last to avoid damage to your model. • Always turn on the transmitter before plugging in the battery.
TRAXXAS TQi RADIO SYSTEM Using the Radio System Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. The TQi Radio System has been pre-adjusted at the factory. The adjustment should be checked before running the model, in case of movement during shipping. Here’s how: 1. Turn the transmitter switch on.
TRAXXAS TQi RADIO SYSTEM Steering Sensitivity (Exponential) The Multi-Function knob on the TQi transmitter has been programmed to control Steering Sensitivity (also known as exponential). The standard setting for Steering Sensitivity is “normal (zero exponential),” with the dial full left in its range of travel. This setting provides linear servo response; the steering servo’s movement will correspond exactly with the input from the transmitter’s steering wheel.
ADJUSTING THE SPEED CONTROL Mamba Monster Extreme Specs Refer to the included Castle Driver’s Ed Guide instruction manual for full speed control operation details. Cells: 18 NiCD / NiMH 6s LiPo Resistance: 0.0003 Ohms per phase Brake : Proportional with adjustable curve Reversible: Yes - with lockout Low Voltage Cutoff: Programmable Case Size: 2.2” x 1.9” x 1.4” Weight with Wires: 121g Connector Type: 6.
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. The instructions that follow are for operating the model up to its electronically-limited top speed of 50mph. Additional registration, setup steps and precautions are required before operating your model at its maximum, unrestricted speed.
BASIC TUNING ADJUSTMENTS All of the toe links are installed on the model so the left-hand thread indicators point to the same direction. This makes it easier to remember which way to turn the wrench to increase or decrease toe link length (the direction is same at all four corners). Note that the groove in the hex indicates the side of the toe link with the left-hand threads.
BASIC TUNING ADJUSTMENTS Use stiffer springs to reduce bottoming out the chassis, reduce body lean, control brake dive, and provide a firmer, more responsive feel. Increasing the spring rate will increase the responsiveness of the suspension. This may be beneficial in some conditions, but may make the car feel twitchy or ‘nervous’ in others. Decreasing spring rate decreases the responsiveness of the suspension, making it easier to drive.
BASIC TUNING ADJUSTMENTS The Power System is NOT WATERPROOF. Do not expose the power system to any type of water, condensation, or moisture. 3. Empty the used shock oil from the shock body. RECEIVER BOX: MAINTAINING A WATERTIGHT SEAL 4. Fill the shock with new silicone shock oil up to the top of the shock body. Removing and Installing Radio Gear The unique design of the receiver box allows the removal and installation of the receiver without losing the ability to maintain a watertight seal in the box.
MAINTAINING YOUR MODEL Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Frequently inspect the vehicle for obvious damage or wear. Look for: 1. Cracked, bent, or damaged parts. 2. Check the wheels and steering for binding. 3. Check the operation of the shock absorbers. 4. Check the wiring for any frayed wires or loose connections. 5. Check the mounting of the receiver and servo(s) and speed control. 6.
MAINTAINING YOUR MODEL Suspension and Cush Drive assembly removal Your model was designed with ease of disassembly in mind. The entire front and rear suspension assemblies can be removed from the chassis fully intact with the removal of only a few screws. Refer to the exploded views included in the Service and Support Guide for complete assembly diagrams. • Removing the front suspension module 1. Remove the four 4x15 countersunk screws from the underside of the chassis. 2.
ADVANCED TUNING ADJUSTMENTS CAMBER GAIN Your model has provisions for adjusting the camber gain geometry of the front and rear suspension. “Camber gain” refers to an increase in camber angle as the suspension is compressed. The camber gain of the vehicle can be changed inside or outside by moving the camber link attachment to a different horizontal mounting position. Adjusting the camber gain will alter the tire contact patch as the suspension is compressed.
ADVANCED TUNING ADJUSTMENTS Gearing Compatibility Chart: The chart below shows recommended gear combination ranges for your model. Spur Gear 46 50 54 - 12.94 13.97 12 - 11.86 12.81 13 10.07 10.95 11.82 14 9.35 10.16 10.98 15 8.73 9.49 10.25 16 8.18 8.89 9.61 17 7.70 8.37 9.04 18 7.27 7.91 8.54 19 6.89 7.49 8.09 20 6.55 7.12 7.68 21 6.23 6.78 7.32 22 5.95 6.47 6.99 23 5.69 6.19 6.68 24 5.46 5.93 6.40 25 5.24 5.69 6.15 26 5.04 5.47 5.91 27 4.
ADVANCED TUNING ADJUSTMENTS 4. Remove the two 3x15mm button head screws from the differential cover and set the differential cover aside. Front Differential Removal 3. 3x15 BCS 5. Remove the two screw pins that fasten the driveshafts to the differential output. 5. 3x15 BCS 6. Installation is the reverse of above. 6. 4. 3x15 BCS 1. 4x15 CCS 2. 4x30 CCS 5. Remove the two 3x15mm button head screws from the differential cover and set the differential cover aside. 6.
EXPERTS ONLY: OPERATING THE XO-1 AT MAXIMUM SPEED For Expert Drivers WARNING! RISK OF INJURY OR DEATH Experts Only! This product is not a toy. This product carries our highest skill level rating, 10, and is not intended for use by children or minors under the age of 16. Individuals under the age of 18 require responsible adult supervision during operation and maintenance. The XO-1 is only intended to be owned and operated by experienced users, with advanced skills, and expert driving ability.
OPERATING THE XO-1 AT MAXIMUM SPEED 2. Download and install the Traxxas Link application from the App Store. 3. Open the Traxxas Link application and touch the Unlock icon. Follow the prompts to register your model. You will be asked to accept the terms of use and provide an e-mail address. Make certain you can access the address you provide. 4. The application will send you an e-mail to confirm your registration information. Open the e-mail and follow the confirmation link. 5.
OPERATING THE XO-1 AT MAXIMUM SPEED WARNING! RISK OF INJURY OR DEATH Experts Only! This product is not a toy. This product carries our highest skill level rating, 10, and is not intended for use by children or minors under the age of 16. Individuals under the age of 18 require responsible adult supervision during operation and maintenance. The XO-1 is only intended to be owned and operated by experienced users, with advanced skills, and expert driving ability.
TQi ADVANCED TUNING GUIDE The XO-1’s TQi transmitter is equipped with the new TQi Docking Base. This innovative accessory transforms your iPhone® or iPod touch® into a powerful tuning tool that equips your TQi with an intuitive, high-definition, full-color graphical user interface. Traxxas Link The powerful Traxxas Link app (available in the Apple App Store) gives you complete control over the operation and tuning of your Traxxas model with stunning visuals and absolute precision.
TQi ADVANCED TUNING GUIDE Throttle Trim Seek Mode When the Multi-Function knob is set to throttle trim, the transmitter remembers the throttle trim setting. If the throttle trim knob is moved from the original setting while the transmitter is off, or while the transmitter was used to control another model, the transmitter ignores the actual position of the trim knob. This prevents the model from accidentally running away.
TQi ADVANCED TUNING GUIDE Press MENU to move through options. Press SET to select an option. MENU TREE The menu tree below shows how to navigate through the TQi transmitter’s various settings and functions. Press and hold MENU to enter the menu tree, and use the following commands to navigate through the menu and select options. MENU: When you enter a menu, you always start at the top. Press MENU to move down the menu tree.
TQi ADVANCED TUNING GUIDE Starting Over: Restoring Factory Defaults When programming your 2.4GHz transmitter, you may feel the need to start over with a clean slate. Follow these simple steps to restore the factory settings: 1. Turn transmitter off. 2. Hold both MENU and SET. 3. Turn transmitter on. 4. Release MENU and SET. The transmitter LED will blink red. 5. Press MENU once. The transmitter LED will blink red twice repeatedly. 6. Press SET to clear settings.
TQi ADVANCED TUNING GUIDE x8 Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press SET to confirm green LED blinks (x8) Set Multi-Function knob for THROTTLE SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU to confirm red LED blinks (x2) Set Multi-Function knob for STEERING DUAL RATE (%) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU twice red LED blinks (x3) Set Multi-
MODEL 6407X OWNER’S MANUAL 6200 Traxxas Way, McKinney, Texas 75070 1-888-TRAXXAS 140113 KC2016-R01 “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod and iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.
