owners manual MODEL 3707 / 3707L MODEL 3607 / 3607L MODEL 2407 / 2407L extreme brushless power system
INTRODUCTION 3 BEFORE YOU PROCEED 3 SAFETY PRECAUTIONS 6 BANDIT VXL OVERVIEW 7 STAMPEDE VXL OVERVIEW 8 RUSTLER VXL OVERVIEW 9 TOOLS, SUPPLIES AND REQUIRED EQUIPMENT 10 QUICK START: GETTING UP TO SPEED 11 TRAXXAS TQi RADIO AND VELINEON POWER SYSTEM 20 ADJUSTING THE ELECTRONIC SPEED CONTROL 22 DRIVING YOUR MODEL 24 BASIC TUNING ADJUSTMENTS 26 MAINTAINING YOUR MODEL 27 ADVANCED TUNING ADJUSTMENTS 29 TQi ADVANCED TUNING GUIDE Thank you for purchasing a Traxxas electric model equipped with
BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and examine the model carefully. If for some reason you decide it is not what you wanted, then do not continue any further. Your hobby dealer absolutely cannot accept a model for return or exchange after it has been run.
SAFETY PRECAUTIONS All instructions and precautions outlined in this manual should be strictly followed to ensure safe operation of your model. This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. Gearing and battery choice (see LiPo Batteries, right) effect the skill level of the model. See chart below. Gearing: Battery: Voltage*: mAh: Stock Pinion 6-Cell NiMH 7.2V 3000+mAh Gearing: Battery: Voltage*: mAh: Opt.
SAFETY PRECAUTIONS NiMH or NiCD charger or charge mode will damage the batteries and may cause fire and personal injury. Never charge LiPo battery packs in series or parallel with this charger. Charging packs in series or parallel may result in improper charger cell recognition and an improper charging rate that may lead to overcharging, cell imbalance, cell damage and fire. • ALWAYS inspect your LiPo batteries carefully before charging.
BANDIT VXL OVERVIEW Rear Camber Link Electronic Speed Control Steering Block Battery Hold-Down Half Shaft Chassis Caster Block Traxxas High-Current Connector Rear Shock Tower Upper Chassis Plate Front Body Mount Rear Body Mount Front Suspension Arm Motor Front Bumper Transmission Front Shock Tower Pinion Gear Shock Spur Gear Receiver Box Antenna Mount Front Camber Link Slipper Clutch LED Light Pipe Rear Suspension Arm 6 • TR A X X AS Wing Mounting Hole Steering Servo Battery Compartment To
STAMPEDE VXL OVERVIEW Half Shaft Rear Shock Tower Front Body Mount Electronic Speed Control Traxxas High-Current Connector Rear Body Mount Steering Block Caster Block Battery Hold-Down Motor Toe Link Chassis Transmission Front Suspension Arm Wheelie Bar Front Bumper Steering Servo Front Shock Tower Antenna Mount Shock Pinion Gear Front Camber Link Spur Gear Receiver Box Battery Compartment Slipper Clutch LED Light Pipe Rear Suspension Arm Rear Camber Link TR A X X AS • 7
RUSTLER VXL OVERVIEW Rear Camber Link Electronic Speed Control Half Shaft Battery Hold-Down Steering Block Caster Block Chassis Rear Shock Tower Traxxas High-Current Connector Upper Chassis Plate Front Camber Link Rear Body Mount Front Suspension Arm Motor Transmission Front Bumper Pinion Gear Front Shock Tower Spur Gear Antenna Mount Receiver Box Shock Slipper Clutch Rear Suspension Arm 8 • TR A X X AS LED Light Pipe Battery Compartment Steering Servo Front Body Mount Toe Link
TOOLS, SUPPLIES AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Supplied Tools and Equipment 2.5mm “L” wrench Optional pinion gear 2.0mm “L” wrench 1.
QUICK START: GETTING UP TO SPEED The Quick Start Guide is not intended to replace the full operating instructions available in this manual. Please read this entire manual for complete instructions on the proper use and maintenance of your model. The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM INTRODUCTION Your model includes the latest Traxxas TQi 2.4GHz transmitter with Traxxas Link™ Model Memory. The transmitter’s easy-to-use design provides instant driving fun for new R/C enthusiasts, and also offers a full compliment of pro-level tuning features for advanced users – or anyone interested in experimenting with the performance of their model. The steering and throttle channels feature adjustable Exponential, End Points, and Sub-Trims.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM To prevent loss of radio range do not kink or cut the black wire, do not bend or cut the metal tip, and do not bend or cut the white wire at the end of the metal tip. Good charging procedures are required to reduce the possibility of developing a “memory” effect and shortened run times. NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH batteries offer high current handling, and much greater resistance to the “memory” effect.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM Your model is equipped with the newest TQi 2.4GHz transmitter with Traxxas Link™ Model Memory. The transmitter has two channels for controlling your throttle and steering. The receiver inside the model has 5 output channels. Your model is equipped with one servo and an electronic speed control.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM If the power indicator doesn’t light green, check the polarity of the batteries. Check rechargeable batteries for a full charge. If you see any other flashing signal from the LED, refer to the chart on page 30 to identify the code. INSTALLING TRANSMITTER BATTERIES CHARGING THE NiMH BATTERY PACK Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM CHARGING THE LiPo BATTERY PACK (Models #2407L / #3607L / #3707L) Using Other Batteries Before charging the provided 2-Cell LiPo battery please read an understand all safety precautions at the beginning of this manual. The included charger can be used to charge the provided battery pack. The supplied charger has an output rate of 800mAh (0.8 amps), and may require up to seven hours to fully charge a battery.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM The following Traxxas High Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector. Part #3060 Single Male/Female Part #3080 2-Pack Female Part #3061 Male Charge Adapter Part #3070 2-Pack Male Installing the Battery Pack Place the battery pack into the battery compartment of the model and then place the battery hold-down over the posts.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM RADIO SYSTEM CONTROLS • In order for the transmitter and receiver to bind to one another, the receiver in the model must be turned on within 20 seconds of turning on the transmitter. The transmitter LED will flash fast red indicating a failure to link. If you miss it, simply turn off the transmitter and start over. Remember, always turn the TQi transmitter on first and off last to avoid damage to your model.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM Using the Radio System Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. The TQi Radio System has been pre-adjusted at the factory. The adjustment should be checked before running the model, in case of movement during shipping. Here’s how: 1. Turn the transmitter switch on.
TRAXXAS TQi RADIO & VELINEON Power SYSTEM 3. When the transmitter and receiver’s LEDs turn solid green, the system is bound and ready for use. Confirm that the steering and throttle operate properly before driving your model. Steering Sensitivity (Exponential) The Multi-Function knob on the TQi transmitter has been programmed to control Steering Sensitivity (also known as exponential).
ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s BATTERY SETTINGS VXL-3s Specifications Input voltage: 4.8-11.1V (4 to 9 cells NiMH or 2S to 3S LiPo) Supported Motors: Brushed Brushless Sensorless brushless Motor limit: None Continuous current: 200A Peak current : 320A BEC voltage: 6.0V DC Transistor type: MOSFET Battery connector: Traxxas High-Current Connector Motor connectors: TRX 3.
ADJUSTING THE ELECTRONIC SPEED CONTROL 6. To stop, return the throttle trigger to neutral. Note that there is programmed delay when changing from reverse to forward. This prevents damage to the transmission on high-traction surfaces. 7. To turn the VXL-3s off, press the EZ-Set button until the LED turns off (about .5 seconds). VXL-3s PROFILE SELECTION The speed control is factory set to Profile #1 (100% forward, brakes, and reverse).
DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly important when using high capacity battery packs that allow extended periods of running. Monitoring temperatures will extend the lives of the batteries and motors.
DRIVING YOUR MODEL Before Running Your Vehicle in Wet Conditions 1. Consult the section “After Running Your Vehicle in Wet Conditions” before proceeding. Make sure you understand the additional maintenance required with wet running. 2. The wheels have small holes molded in to allow air to enter and exit the tire during normal running. Water will enter these holes and get trapped inside the tires if holes are not cut in the tires. Cut two small holes (3mm or 1/8” diameter) in each tire.
BASIC TUNING ADJUSTMENTS All of the toe links are installed on the truck so the left hand thread indicators point to the same direction. This makes it easier to remember which way to turn the wrench to increase or decrease toe link length (the direction is same at all four corners). Note that the groove in the hex indicates the side of the toe link with the left-hand threads.
BASIC TUNING ADJUSTMENTS hard, dry surfaces. In loose dirt, a tire with large spikes should perform better. See your parts list for accessory wheels and tires. Adjusting the Slipper Clutch The model is equipped with an adjustable slipper clutch which is built into the large spur gear. The purpose of the slipper clutch Tighten is to regulate the amount of power sent to the rear wheels to prevent tire spin. When it slips, the slipper clutch Loosen makes a high-pitch, whining noise.
MAINTAINING YOUR MODEL Always wear eye protection when using compressed air or spray cleaners and lubricants. High performance vehicles generate small vibrations while driving. These vibrations may loosen hardware over time and require attention. Always check your wheel nuts and other hardware and tighten or replace when necessary. Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously.
ADVANCED TUNING ADJUSTMENTS # Spur Gear Teeth x 2.72 = Final Gear Ratio # Pinion Gear Teeth When using higher gear ratios, it is important to monitor the temperatures of the battery and motor. If the battery is extremely hot, and/or the motor is too hot to touch, your model is probably over-geared and drawing too much current.
ADVANCED TUNING ADJUSTMENTS Velineon 3500 Specs Type: Sensorless brushless RPM/volt: 3500 (10-turn) Magnet type: Ultra High-Temperature Sintered Neodymium Connection type : 3.5mm bullet Wire size: 12 Gauge Current Ratings: 200A constant 320A peak/burst Max RPM: 50,000 Diameter: 36mm (1.42") (540 size) Length: 55mm (2.165") Weight: 262g (9.24oz) Always use the proper length motor bolts. The standard motor mounting bolts are 3x8mm.
TQi ADVANCED TUNING GUIDE Your Traxxas transmitter has a programmable Multi-Function knob that can be set to control various advanced transmitter functions (set to Steering Sensitivity by default, see page 19). Accessing the programming menu is done by using the menu and set buttons on the transmitter and observing signals from the LED. An explanation of the menu structure follows on page 31. Experiment with the settings and features to see if they can improve your driving experience.
TQi ADVANCED TUNING GUIDE Failsafe Your Traxxas radio system is equipped with a built-in failsafe function that returns the throttle to its last saved neutral position in the event of a signal loss. The LED on the transmitter and the receiver will rapidly flash red. Model Lock The Traxxas Link Model Memory feature can store up to twenty models (receivers) in its memory.
TQi ADVANCED TUNING GUIDE Press MENU to move through options. Press SET to select an option. MENU TREE The menu tree below shows how to navigate through the TQi transmitter’s various settings and functions. Press and hold MENU to enter the menu tree, and use the following commands to navigate through the menu and select options. MENU: When you enter a menu, you always start at the top. Press MENU to move down the menu tree.
TQi ADVANCED TUNING GUIDE x8 Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press SET to confirm green LED blinks (x8) Set Multi-Function knob for THROTTLE SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU to confirm red LED blinks (x2) Set Multi-Function knob for STEERING DUAL RATE (%) Press/hold MENU green LED blinks Press SET red LED blinks Press MENU twice red LED blinks (x3) Set Multi-F
TQi ADVANCED TUNING GUIDE PROGRAMMING YOUR TQi TRANSMITTER WITH YOUR APPLE iPHONE OR iPOD TOUCH The Traxxas Docking Base (Part #6510 - sold separately) for the TQi transmitter installs in minutes to transform your iPhone® or iPod touch® into a powerful tuning tool that allows you to replace the transmitter’s button/LED programming system with an intuitive, high-definition, fullcolor graphical user interface.
1100 Klein Road, Plano Texas 75074 1-888-TRAXXAS 120912 2407-3607-3707OM-LN-EN-R00
