TRA82056-4RED Traxxas TRX-4 Manual

TRX-4
•
19
ADJUSTING THE ELECTRONIC SPEED CONTROL
Patented Training Mode
(Profile #3) reduces forward
and reverse throttle by 50%.
Training Mode is provided
to reduce the power output,
allowing beginning drivers to
better control the model. As
driving skills improve, simply
change to Sport, Race, Trail,
or Crawl Mode for full-power
operation.
Tip For Fast Mode Changes
The XL-5 HV is set to Profile 4
(Trail Mode) as the default.
To quickly change to Profile 3
(Training Mode), with the
transmitter on, press and hold
the EZ-Set button until the light
blinks red three times and then
release. Quickly change back to
Profile 4 (Trail Mode) by pressing
and holding the EZ-Set button
until the light blinks red four
times and then releasing.
release too quickly, you may hear the steering servo jump but the
LED may not stay on. Simply press the button again until the LED
shines GREEN, and then release.
2. Apply forward throttle. The LED will turn off until full throttle power
is reached. At full throttle, the LED will shine GREEN.
3. Move the trigger forward to apply the brakes. Note that braking
control is fully proportional. The LED will turn off until full braking
power is reached. At full brakes, the LED will shine GREEN.
4. Return the throttle trigger to neutral. The LED will shine GREEN.
5. Move the throttle trigger forward again to engage reverse (Profile
#1). The LED will turn off. Once full reverse power is reached, the
LED will shine GREEN.
6. To stop, return the throttle trigger to neutral. Note that there is
no programmed delay when changing from reverse to forward.
Use caution to avoid slamming the speed control from reverse to
forward. On high-traction surfaces, this could result in transmission
or driveline damage.
7. To turn the XL-5 HV off, press and hold the EZ-Set button for 1½
seconds or until the green LED turns off.
8. The XL-5 HV is equipped with thermal shutdown protection to
guard against overheating caused by excessive current flow. If
the operating temperature exceeds safe limits, the XL-5 HV will
automatically shut down. The LED on the face of the XL-5 HV will
rapidly blink red, even if the throttle trigger is moved back and
forth. Once the temperature returns to a safe level, the XL-5 HV will
once again function normally.
XL-5 HV Profile Selection
The speed control is factory set to Trail Mode (100% forward, brakes,
and reverse; added brake drag when the throttle trigger is at neutral).
To activate full power without the additional brake drag (Sport Mode),
disable reverse (Race Mode), allow 50% power (patented Training
Mode), or set immediate reverse (Crawl Mode), follow these steps. The
speed control should be connected to the receiver and the transmitter
adjusted as described previously. The profiles are selected by entering
the programming mode.
Profile Description
Profile #1 (Sport Mode): 100% Forward, 100% Brakes, 100% Reverse
Profile #2 (Race Mode): 100% Forward, 100% Brakes, No Reverse
Profile #3 (Training Mode): 50% Forward, 100% Brakes, 50% Reverse
Profile #4 (Trail Mode): 100% Forward, 100% Brakes, 100% Reverse;
Drag Brake at Neutral
Profile #5 (Crawl Mode): 100% Forward, Hill Hold Brakes at Neutral,
Immediate Reverse
Selecting Sport Mode
(Profile #1: 100% Forward, 100% Brakes, 100% Reverse)
1. Connect a fully charged battery pack to
the XL-5 HV and turn on your transmitter.
2. With the XL-5 HV off, press and hold
the EZ-Set button until the LED turns
solid green, then solid red and then
begins blinking red (indicating the
Profile numbers).
3. When the LED blinks RED ONCE, release
the EZ-Set button.
4. The LED will blink and then turn solid green (Low-Voltage Detection
ACTIVE) or red (Low-Voltage Detection DISABLED). The model is
ready to drive.
Selecting Race Mode
(Profile #2: 100% Forward, 100% Brakes, No Reverse)
1. Connect a fully charged battery pack to
the XL-5 HV and turn on your transmitter.
2. With the XL-5 HV off, press and hold
the EZ-Set button until the LED turns
solid green, then solid red and then
begins blinking red (indicating the Profile
numbers).
3. When the LED blinks RED TWICE, release
the EZ-Set button.
4. The LED will blink and then turn solid green (Low-Voltage Detection
ACTIVE) or red (Low-Voltage Detection DISABLED). The model is
ready to drive.
Selecting Training Mode
(Profile #3: 50% Forward, 100% Brakes, 50% Reverse)
1. Connect a fully charged battery pack to
the XL-5 and turn on your transmitter.
2. With the XL-5 off, press and hold the
EZ-Set button until the LED turns solid
green, then solid red and then begins
blinking red (indicating the Profile
numbers).
3. When the LED blinks RED THREE
TIMES, release the EZ-Set button.
4. The LED will blink and then turn solid green (Low-Voltage Detection
ACTIVE) or red (Low-Voltage Detection DISABLED).
The model is ready to drive.
B
One blink Red
A
Green to Red to Off
D
Solid
C
Release
B
Two blinks Red
A
Green to Red to Off
D
Solid
C
Release
B
Three blinks Red
A
Green to Red to Off
D
Solid
C
Release