Specifications

ManualsBrandsTrek Bicycle ManualsElectronicsIon Pro RT

Pairing to the Transmitr Remote, Bontrager Garmin Edge

GPS computer or select Garmin Edge

computers

The Transmitr Remote (or select Garmin Edge computers, sold separately)

allows remote control of the light. This feature is only available on the Ion Pro RT,

Ion 200 RT, and the Flare RT as well as other compatible Transmitr lights.

For more complete instructions, refer to the Transmitr manual at

trekbikes.com. For Garmin related instruction and a complete listing of

compatible Edge devices visit support: garmin.com.

Before starting, place the remote and all lights within a small area. Move 15 feet

from other Transmitr / ANT+ compatible lights to prevent unintentional pairing. If

a light is unintentionally paired, restart the pairing process at the beginning.

NOTE: All pairings must be done in a single session. After pairing is

ﬁnished, pairing any additional lights will require that you repeat the entire

pairing procedure.

1. Place the light close to the Transmitr Remote (within 15cm / 6in).

2. Quick-press the power button on the light to turn it on, then quick-press to

turn it off again.

NOTE: After completing this step, do not press the power button on the light

again until pairing is complete.

3. Press-and-hold the center button on the Transmitr Remote for at least 8

seconds. When the corner buttons ﬂash, release the center button.

4. While the remote searches for a light, its center button ﬂashes red. When

the Transmitr Remote ﬁnds a light, the center button on the remote will change

from red to green, and the found light will ﬂash.

5. While the found light is still ﬂashing, quick-press the button on the Transmitr

Remote to which you would like to pair the light. The selected button will glow,

and the found (paired) light will stop ﬂashing and turn off.

NOTE: After the pairing, the center button on the remote will ﬂash red until the

Transmitr Remote ﬁnds another available light.

6. Repeat Step 4 and Step 5 for each additional light to be paired.

To exit pairing

1. When all lights are paired, quick-press the center button on the remote. The

button will stop ﬂashing and turn off.

To verify pairing

1. Quick-press the center button on the remote to turn on all paired lights.

2. Press-and-hold the center button to turn off all of them.

3. Turn on each light individually. Quick-press each paired corner button on the

remote to turn on the individual light(s).

4. Press-and-hold the same corner button to turn off the light.

Using the Transmitr Remote

To turn on all lights

ON: Quick-press the center button.

OFF: Press and hold the center button.

To turn on an individual light

ON: Quick-press the corner button that controls the light.

OFF: Press and hold the same button.

To change modes of an individual light

Each quick-press of a button that controls a light will cycle through the modes.

To see battery power status on the remote

When a corner button is pressed, the center button will show the battery status

of the light.

Center Button Color Battery Life, %

Flashing red Less than 5

Red Between 5 and 25

Green More than 25

Ion 200 RT information, installation,

and special features

Installation

To attach with the Quick Connect 0˚ offset bracket

1. Place the quick connect on the handlebar with the hook in front.

2. Stretch the strap under the bar and connect to the hook.

NOTE: Use the second hook to latch excess strap.

3. Slide the Ion 200 RT onto the bracket until it clicks. The power button

should be facing up and the lens of the light should be perpendicular to

the road.

Removal

Press down on the tab and

slide the light away from

the lever.

Alternatively, you can

remove the entire quick-connect bracket, with the light attached.

2. Remove

1. Press

Low battery feature

When the battery charge drops below 5% the light automatically adjusts the

output brightness to 5 lumens. This extends the light output for an additional

30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button

8 seconds to select it. The light will turn off and the main LED will ﬂash once.

To unlock, repeat the process.

Auto brightness

The light is shipped with an ambient light sensor disabled. When the ambient

light sensor is enabled, the light automatically changes modes with ambient

light conditions. It changes from Day Flash to High Steady. To enable, press

and hold the power button 8 seconds. The light will ﬂash once.

NOTE: When auto brightness is enabled, all modes are manually accessible.

Reset

To reset the light to factory default settings, with the light on, press and hold the

power button for 15 seconds. The main LED will ﬂash once at 8 seconds, and

again at 15 seconds. Release the button after the second ﬂash.

Wireless Communication

The light is shipped with ANT+ and Bluetooth wireless connectivity enabled.

To disable, with the light off, press and hold the power button for 15 seconds.

The main LED will ﬂash once at 8 seconds, and again at 15 seconds. Release

the button after the second ﬂash.

NOTE: The status LED turns on blue for 3 seconds IF the wireless is enabled.

After 3 seconds, the status LED continues to display the battery level. If the

wireless is disabled, the status LED immediately displays the battery level.

Flare RT information, installation,

and special features

Installation

To attach with the Quick Connect

16˚ offset bracket

IMPORTANT: The seatpost/saddle icon shows that

the lens is oriented perpendicular to the ground to optimize visibility.

NOTE: Use the second hook to latch any excess strap.

To attach to a seat pack

Attach the seat pack clip to the bag loop. To optimize visibility,

ensure the light lens is oriented perpendicular to the ground.

To attach to a rack

Remove the quick connect clip from the rubber strap and

attach to a rack with a M5 bolt and washer, sold separately,

PN 537061.

Low battery feature

When the battery charge drops below 5% the light

automatically adjusts the output brightness and begins

to ﬂash. This extends the light output for an additional

30 minutes.

Locking/Unlocking the mode

Turn on and select the desired mode, then press and hold the power button

8 seconds to select it. The light will turn off and the main LED will ﬂash once.

To unlock, repeat the process.

Auto brightness

The light is shipped with an ambient light sensor disabled. When the ambient

light sensor is enabled, the light automatically changes modes with ambient

light conditions. It changes from Day Flash or All Day Flash to Night Flash,

OR Day Steady to Night Steady. To enable, press and hold the power button

8 seconds. The light will ﬂash once.

NOTE: When auto brightness is enabled, Day Flash, All Day Flash and Day

Steady are manually accessible.

Reset

To reset the light to factory default settings, with the light on, press and hold the

power button for 15 seconds. The main LED will ﬂash once at 8 seconds, and

again at 15 seconds. Release the button after the second ﬂash.

Wireless Communication

The light is shipped with ANT+ and Bluetooth wireless connectivity enabled.

To disable, with the light off, press and hold the power button for 15 seconds.

The main LED will ﬂash once at 8 seconds, and again at 15 seconds. Release

the button after the second ﬂash.

NOTE: The status LED turns on blue for 3 seconds IF the wireless is enabled.

After 3 seconds, the status LED continues to display the battery level. If the

wireless is disabled, the status LED immediately displays the battery level.

A bicycle without correct lights and reﬂectors might be difﬁcult for other

people to see, and you might not be able to see. If you cannot see, or other

people cannot see you, you could have an accident. Make sure your lights

operate correctly and that batteries are charged.

WARNING

Front of bike

Trek Bicycle Corporation contact information:

North America

Trek Bicycle Corporation

801 West Madison Street

Waterloo, WI 53594 USA

Tel: 800-313-8735

Europe

Bikeurope BV

Ceintuurbaan 2-20C

3847 LG Harderwijk

The Netherlands

Tel: +31 (0)88 4500699

Australia

Trek Bicycle Corp. Au.

8 Townsville Street

(Level One)

Fyshwick (ACT)

2609 AU

Tel: +61 (02) 61 732 400

Statements of Regulatory Compliance

FCC Compliance

Ion Pro RT

FCC ID: 2AHXD-552373

Ion 200 RT/Flare RT FCC ID: 2AHXD553852

This device complies with part 15 of the FCC Rules. Operation is subject to the

following conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that

may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation.

This product may cause interference to radio equipment and should not be

installed near maritime safety communications equipment or other critical

navigation or communication equipment operating between 0.45-30 MHz.

If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the

following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

— Consult the dealer or experienced radio / TV technician for help.

NOTES: TREK BICYCLE CORPORATION IS NOT RESPONSIBLE FOR

ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED

MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR

MODIFICATIONS NOT EXPRESSLY APPROVED BY TREK BICYCLE

CORPORATION OF THIS DEVICE COULD VOID THE USER’S AUTHORITY

TO OPERATE THE DEVICE.

Industry Canada Compliance

Ion Pro RT (P/N 552373) IC ID: 21334-552373

Ion 200 RT (P/N 553853) IC ID: 21334-553852

Flare RT (P/N 553852) IC ID: 21334-553852

CAN ICES-3(B)/NMB-3(B)

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Leprésent appareil est conforme aux CNR d’Industrie Canada applicable aux

appareils radio. Exempts de licence. L’exploitation est autorisée aux deux

conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilsateur de l’appareil

doit accepter tout brouillage radioélectrque subi, meme si le brouillage est

susceptible d’en compromettre le fonctionnement.

This Ion Pro RT lighting equipment complies with FCC and IC radiation

exposure limits set forth for an uncontrolled environment. The radiated output

power of the Ion Pro RT Wireless Device is below the Industry Canada (IC)

radio frequency exposure limits, when used as directed in this manual (Note:

attaching this light to a helmet changes the absorption characteristics of the

light-body system). This equipment is in direct contact with the body of the user

under normal operating conditions. This transmitter must not be colocated or

operating in conjunction with any other antenna or transmitter. Status of the

listing in the Industry Canada’s REL (Radio Equipment List) can be found at the

following web address:

http://www.ic.gc.ca/app/sitt/reltel/srch/ nwRdSrch.do?lang=eng

Additional Canadian information on RF exposure also can be found at the

following web address:

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08792.html

Cet appareil est conforme aux limites d’exposition à la fréquence radio (FR)

d’IC et de FCC. La puissance de sortie émise par l’appareil de sans ﬁl Ion

Pro RT est inférieure à la limite d’exposition aux fréquences radio d’Industry

Canada (IC). Cet appareil est en contact direct avec l’utilisateur dans des

conditions normales d’utilisation. L’émetteur ne doit pas être co-implémenté

ou utilisé conjointement avec une autre antenne ou un autre émetteur. Ce

périphérique est homologué pour l’utilisation au Canada. Pour consulter

l’entrée correspondant à l’appareil dans la liste d’équipement radio (REL -

Radio Equipment List)d’Industry Canada rendez-vous sur:

http://www.ic.gc.ca/app/sitt/reltel/srch/nwRdSrch. do?lang=fra

Pour des informations supplémentaires concernant l’exposition aux RF au

Canada rendezvous sur:

http://www.ic.gc.ca/eic/site/smt-gst.nsf/fra/sf08792.html

European Union Compliance

Ion Pro RT and Ion 200 RT do not comply with German StVZO regulations!

Trek Bicycle Corporation and Bontrager hereby declare that the wireless device

identiﬁed as ‘Ion Pro RT’, ‘Ion 200 RT’ and ‘Flare RT’ are in compliance with

the following European Directives:

• Radio Equipment Directive 2014/53/EU (Ion Pro RT only)

• EMC Directive 2014/30/EU

• Low Voltage Directive 2014/35/EU (Ion Pro RT only

• RoHS Directive 2011/65/EU

The full text of the EU declaration of conformity is available from your dealer, or

at the following internet address: http://www.trekbikes.com/support

If you wish to see this manual in another language, please visit

trekbikes.com/manuals and look for the Ion Pro RT/Ion 200 RT/Flare RT

manual on the Manuals and user guides page.

DE Wenn Sie dieses Handbuch in einer anderen Sprache sehen möchten,

besuchen Sie bitte www.trekbikes.com/support und suchen Sie nach dem

Handbuch Ion Pro RT / Ion 200 RT / Flare RT auf der Seite Handbücher

und Benutzerhandbücher.

FR Si vous souhaitez voir ce manuel dans une autre langue, rendez-vous sur

www.trekbikes.com/support et recherchez le manuel Ion Pro RT / Ion 200

RT / Flare RT sur la page Manuels et guides de l’utilisateur.

ES Si desea ver este manual en otro idioma, visite www.trekbikes.com/support

y busque el manual Ion Pro RT / Ion 200 RT / Flare RT en la página

Manuales y guías del usuario.

IT Se si desidera vedere questo manuale in un’altra lingua, visitare

www.trekbikes.com/support e cercare il manuale Ion Pro RT / Ion 200 RT /

Flare RT nella pagina Manuali e manuali dell’utente.

PL Jeśli chcesz zobaczyć tę instrukcję w innym języku, odwiedź stronę

www.trekbikes.com/support i poszukaj instrukcji Ion Pro RT / Ion 200 RT /

Flare RT na stronie Podręczniki i instrukcje obsługi.

PT Se você deseja ver este manual em outro idioma, visite

www.trekbikes.com/support e procure o manual do Ion Pro RT / Íon 200

RT / Flare RT na página Manuais e guias do usuário.

NL Als u deze handleiding in een andere taal wilt bekijken, gaat u naar

www.trekbikes.com/support en zoekt u naar de Ion Pro RT / Ion

200 RT / Flare RT-handleiding op de pagina Handleidingen en

gebruikershandleidingen.

JA このマニュアルを別の言語で表示したい場合は、www.trekbikes.com/

supportにアクセスして、マニュアルおよびユーザーガイドページのIon Pro

RT / Ion 200 RT / Flare RTマニュアルを参照してください。

KO 󼓣󾖴󻝓󺿣󼌫󼒳󾖴󻁓󻛧󾖴󼌧󼌣󻗋󻩣󺩏󾖴󼁥󻁓󻟣󻛫

󻦘󻢧󽋇󼍛󾖴󻝓󺿣󼌫󾖴󻥾󾖴󻸛󼐘󼓿󾖴󼊷󺸣󻺋󾖴󽄇󼓣󼜯󼌿󻺋

󻝓󺿣󼌫󼒳󾖴󼦭󼒫󼁜󼁋󼎓

ZH 如果您希望以其他语言查看本手册，请访问www.trekbikes.com/support，

并在手册和用户指南页面上查找Ion Pro RT / Ion 200 RT / Flare RT手册。

إذا كنت ترغب في مشاهدة هذا الدليل بلغة أخرى ، يرجى زيارة

www.trekbikes.com/support وابحث عن Ion Pro RT / Ion 200 RT / Flare RT

دليل على صفحة الأدلة وكتيبات المستخدم.

BT20__MANUAL_IonProRT_200RT_FlareRT_with Warning_360x380mm_572345-2_USEN_REV2020.indd 2

1/3/20 1:54 PM