COCKPIT GB MANUAL www.trelock.
You have decided to purchase the TRELOCK bike computer FC 820 / FC 830 / FC 840 (each with Uni-Base) or FC 845 (Night-Light-Base) and, as such, your choice is an excellent one. Your new bike computer is easy and convenient to operate thanks to the visual guidance system and large mono-button typical of TRELOCK products. Please read through this manual prior to your initial usage of the computer.
Contents 1. Scope of supply 40 2. Insertion of batterie 41 3. Assembly/Installation 42 4. Display design and operating principle 47 5. General default settings 48 6. Main menus 59 7. Training 66 8. Additional information and instructions 66 9.
1. Scope of supply 1.2 FC 845 1.
2. Insertion of batterie 2.1 Sensor When supplied to the customer, the battery has already been inserted into the bike computer. In order to activate the computer, the red plastic flag must first be removed. Turn the battery compartment cap on the bottom of the computer in an anti-clockwise direction and pull the flag out. Then turn the cap firmly back in place.
2.2 Only FC 845 The display for your bike computer is fed via a battery in the night-light base. In order to insert this battery, use a coin to turn the battery compartment cap in an anticlockwise direction and insert the battery with the + sign pointing upwards (see fig.). Then turn the cap firmly back in place. 3. Assembly/Installation 3.
3.
3.
3.
3.
4.
5. General default settings 5.1 Selection of language Once the computer (by removing the plastic tab) has been activated, you automatically access the “Sprache?” (Language) menu. By pressing the SET button, you access the language selection option. Use the MODE button to choose one of the eight languages shown (German, English, French, Dutch, Spanish, Italian, Russian or Polish) and confirm your choice via the SET button.
49
5.2 Choice between km/h and m/h In the “Dimensions?” menu, “km/h” is pre-set as the standard unit. If you wish to accept this default setting, press the MODE button. To change it to “m/h”, press the SET button. Then use the MODE button to choose between “m/h” and “km/h” in the “Unit Speed” window. Confirm your choice via the SET button.
5.3 Choice between °C and °F (only FC 840, 845 ) Use the MODE button to choose between ”°F“ and ”°C“ now. Confirm your choice via the SET button.
5.4 Setting(s) of wheel size(s) (FC 830, 840, 845 ) You can use your cycle computer on 2 cycles – even if the wheels are different sizes. To do this, you need a separate holder and sensor for each cycle. For FC 830/840, you need Art. ZF 406 Uni-Base, ZF 435 transmitter, ZF 50 magnet. For FC 845 you will need Art. ZF 410 Night-LightBase + magnet, ZF 435 transmitter. Press the SET button to make or change the settings for cycle 1 or cycle 2 in the “Settings for cycle” window.
5.5 Entering the code number In the “Code No. 1” bzw. “Code No. 2” window, enter the 4-digit code of the sensor to register this on the computer. Smooth, uninterrupted communication between the computer and the sensor is assured by the Radio Select technology only once the sensor is registered. If the cycle or computer is stolen, the computer is of no use to the thief. You will find the code number on a peel-off sticker on the sensor. You should remove the sticker and stick it in the instruction manual.
5.6 Setting(s) of wheel size(s) (wheel circumference) Under “Wheel Size 1” or “Wheel Size 2” (only for FC 830, 840 845), you should now enter the wheel circumference of your bike. This can be seen from the wheel size data shown on the side of your tyre. Please consult the table shown on P. 55 for the appropriate 4-digit number. Next press the MODE button until such time as the appropriate digit appears, then use the SET button to move to the next digit.
Wheel Size (WS) Chart (wheel sizes / wheel circumference) ETRTO WS mm ETRTO WS mm 47 – 305 47 – 406 50 – 406 60 – 406 37 – 540 47 – 507 50 – 507 40 – 559 44 – 559 47 – 559 50 – 559 54 – 559 57 – 559 37 – 590 20 – 571 16x1.75x2 20x1.75x2 20/2.00 20/2.35 24x1 3/8 A 24x1.75x2 24/2.00 26x1.5 26x1.6 26x1.75x2 26x1.9 26x2.00 26x2.
5.7 Setting the current time If you wish to change the time, press the SET button. One after another, hours, minutes and seconds (start automatically after confirmation of minutes) can be changed via the MODE button. Use the SET button to confirm your entries and to move to the next digit.
5.8 Entering and changing the PIN anti-theft protection You can use a PIN to protect your cycle computer from misuse by unauthorized people. The cycle computer cannot be used unless the correct PIN is entered. Once the time has been set, you automatically access the “Change PIN?” window. Here you can enter your own PIN and, if necessary, subsequently change it. If you don’t wish to use a PIN, press the MODE button.
5.9 Entering and changing the PIN time If the bike computer is in Sleep mode and is not ‘awakened’ for a set time, it has to be reactivated by entering your PIN. The period concerned (PIN Time) can be (re)set in the “Set PIN Time” window – after you have pressed the SET button, you will be asked to enter your PIN. After correct PIN input, you automatically access “PIN Time” where you can enter the time of your choice up to max. 240 minutes.
5.10 Energy economy function An energy economy function is linked to the PIN-time setting. The PIN-time default setting is 60 min. and the PIN default setting “0000”. As such, the clock is displayed in Sleep for 60 min., after which time the clock display shuts down. This period of time can be adjusted as described above. If the PIN time is set at 0, the energy economy function is deactivated and the clock is displayed on an ongoing basis. 6.
6.1 „Stopwatch” menu (only FC 530, 535 ) Starting, stopping and resetting the stopwatch Use the SET button to start and stop the stopwatch. By pressing and holding the SET button for 3 seconds, the stopwatch is reset to “0”. Current speed Stopwatch Menu display 6.2 “Temperature“ menu The Temperature “ temperature.
6.3 “Average” MID menu The “MID“ menu shows the current average speed of the given lap. By pressing and holding the SET button for 3 seconds, you stop the measurement of the current lap and reset all lap readings on the computer to “0”. 6.4 “Maximum” MAX menu Current speed Current time Average speed of the current lap The maximum speed on the given lap is displayed via the “MAX” menu.
6.5 “Lap” TRIP menu The ride time and lap kilometres ridden are displayed via the “TRIP” menu. Current speed Lap ride rime By pressing and holding the SET button for 3 seconds, you stop the measurement of the current lap and reset all lap readings on the computer to “0”. Lap kilometres ridden 6.
3 seconds 6.7 “Total” TOTAL menu Current speed Total ride time (of current bike) Total kilometres of current bike The total kilometre status and total ride time of the current bike are displayed via the “Total” menu. The total kilometre status can be adjusted via the “Set” menu, enabling you, for instance, to transfer the kilometre reading from an old bike computer to your new TRELOCK computer.
6.8 “ DEST” menu (only FC 840, 845) 3 seconds Current speed Remaining journey time (calculated from the remaining distance and the average speed measured to the relevant point) Remaining distance in kilometres (Countdown) Setting the remaining distance counter (Countdown) Press and hold the SET button for 3 seconds. You can now set the remaining distance counter in “Set km”. Use the MODE button to set the first digit, then press the SET button to move on to the next digit and to confirm.
6.9 “Set” SET menu Changing the presetting Current speed Total ride time (for Bikes 1+ 2) Total kilometres (for Bikes 1+ 2) By pressing and holding the SET button in the “SET” menu for 3 seconds, you then have the option of correcting your default settings and making further settings. Pressing the MODE button brings you automatically to the menus “Clock?” “Wheel Size?” with its submenus “Bike 1” and “Bike 2” (not applicable to FC 820) and “Total km” one after the other.
66 7. Training 8. Additional information and instructions 7.1 Targeted training 8.1 Battery change Your TRELOCK bike computer gives you a wide range of options for training in a targeted manner. You have the possibility, for example, of monitoring • how long you train for • how many kilometres you cover • how long you need to cover a certain distance. = When this symbol appears, the battery needs changing.
8.2 Frequently asked questions 8.3 Technical data Why can’t the bike computer be activated? The battery is flat and must be replaced. Operating temperature: 5 ˚C bis 50 ˚C (40 ˚F und 120 ˚F) Why isn’t any other current data displayed apart from the time? The bike computer is in Sleep mode – just press any button of your choice or simply start cycling. Storage temperature: Why is the incorrect speed displayed? The wrong wheel size has been entered.
8.6 Warranty and service You have purchased a quality product from TRELOCK. TRELOCK guarantees the initial purchaser for a period of two years from the date of purchase that this TRELOCK product is free of defects in respect of materials and workmanship, and ensures that any defective product is repaired or replaced with a new product. Any complaints you may have should be addressed directly to your dealer/specialist stockist, who should also be provided with the relevant purchase receipt.
Notes 69
www.trelock.
