963 Installation Instructions Issue 2
Author: Technical Publications Issue: 2 Date: 09/01/2009 Part Number: TG201026 Copyright: © 2009 Honeywell Technologies Sàrl, ECC Division. All rights reserved. This manual contains proprietary information that is protected by copyright. No part of this manual may be reproduced, transcribed, stored in a retrieval system, translated into any language or computer language, or transmitted in any form whatsoever without the prior consent of the publisher.
Table of Contents TABLE OF CONTENTS 1 1.1 1.2 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 ABOUT THESE INSTRUCTIONS................................................................................................................. 5 Conventions Used in this Manual ................................................................................................................ 5 Contacting Trend................................................................................................................................
Table of Contents This page is intentionally left blank.
About These Instructions 1 ABOUT THESE INSTRUCTIONS These instructions apply to 963 version 3.10 software. They provide information about installing, upgrading, and licensing the 963. Other relevant documentation is: 963 Data Sheet (TA200636) 963 Engineering Manual (TE200637) 963 User Guide (TC200635) 963 Web User Guide (TC200685) Product Data Sheets These documents are available in PDF format in the Documentation directory as well as the Data CD-ROM. 1.
About These Instructions This page is intentionally left blank.
Installation 2 INSTALLATION This section describes how 963 should be installed to ensure that it operates correctly. 963 can be run free of charge, for a 28-day trial period but after this a licence must be purchased in order to continue using 963. The process for installing the 963 differs slightly depending on your requirements, and system configuration, you should follow the one that matches your needs. 2.
Installation The use of a dot matrix printer is recommended for alarms. Use of inkjet or laser printers for alarm printing is likely to cause undesirable results e.g. each line of the alarm on a separate page. A separate printer for graphs and schematic pages (graphics printer) is recommended. The graphics printer can be connected using a parallel or USB port. The printer may also be accessed over the office IT network (providing a network card is fitted).
Installation 2.3 Installation for BACnet Communications This section describes the standard installation procedure for installing the 963 if it is to communicate with BACnet devices. To carry out this procedure you must have a copy of the Trend Open Protocol Server TOPS as this is required during the installation. For the 963 to communicate with BACnet devices it must be able to communicate with the Trend Open Protocol Server (TOPS). To install 963 for BACnet communications: 1.
Installation 2.4 Installation for use with a Remote SQL Server This section describes how 963 should be installed for use with a remote SQL Server. To install 963 for use with a remote SQL Server: 1. Ensure that the PC meets the system requirements see the 'System Requirements' section of these instructions for more details. 2. Install the required version of SQL Server.
Installation 2.7 Install the 963 Software The installation of the 963 software is performed by a step-by-step installation program. During the installation procedure you will be required to enter the serial number for the software. This located on the back of the CD case; you should keep this number in a safe place because it will be required when you purchase a licence. Note that if a full version of SQL Server 2000 is already installed then 963 will not upgrade the SQL server.
Installation 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 2.8.2 If it is not displayed in the Serial no box enter the serial number. The serial number can be found on the back of the CD case. Click Licence 963. The Licence Details dialogue box is displayed. In the Contact Name box enter your name. In the Company Name box enter your company name. In the Your Fax No box enter your fax number. This is the fax number to which the unlock code will be faxed.
Installation 6. Click Update, a dialogue box is displayed informing you that the 963 has been licensed. If you want to view a text file containing detailed licence information is displayed click Yes, otherwise click No. Note that the text file containing detailed licence information is '963LicenceDetail.txt' store in the directory the 963 is installed in, and can be viewed in Notepad. 7. Click Close. Note that the procedure described above can also be used to update the licence if it has changed. 8.
Installation 2.10 Configure the GSM Connection If the 963 has been licensed with SMS direct it is necessary to configure the GSM connection that is to be used. The first time 963/…/SMS is run a dialogue box enabling the GSM connection to be configured is displayed. You can choose to configure it then, or it can be done later.
Installation 6. 7. Once the process is completed click OK to return to the SMS Management dialogue box. If 963 found the GSM modem its details will be used. If the GSM modem was not correctly detected you can configure the connection manually as described in the ‘Manually Configure the GSM Connection’ section of these instructions. If a PIN is required to access the SIM enter the required PIN in the SIM PIN box.
Installation 6. If text messages are to include international (UCS-2) characters select the Send as international characters (USC-2) check box. Note that if international characters are used only 70 characters are allowed in the SMS message. If international characters are not used the message can be up to 140 characters. 7. 8. If text messages are to flash on the phone to select the Send as Flash SMS check box.
Installation 9. In the Socket Scan From box enter the port number of the first vCNC in the range of vCNCs to which 963 can connect (e.g. 10005). 10. In the Socket Scan To box enter the port number of the last vCNC in the range of vCNCs to which 963 can connect (e.g. 10006). 963 will be able to connect to the IQ network using any of the ports in the specified range. Because each port has a specific address on the IQ network, the address of 963 on the IQ network will vary depending on which port it uses.
Installation 2.14 SQL Server Installation and Configuration The information contained in this section is only required if a non standard installation of 963 or SQL server is required.
Installation 22. 23. 24. 25. 26. 27. 28. 29. In the Enter password box enter saTrend06. In the Confirm password box enter saTrend06. Click Next>. The Collection Settings screen is displayed. Click Next>. The Configuration Options screen is displayed. Select the Add user to the SQL Server Administrator role check box Click Next>. The Error Usage Report Settings screen is displayed. Click Next>. The Ready to Install screen is displayed. Click Install.
Installation 2.14.1.3 Configure SQL Server 2005 Express Edition with Advanced Services If SQL Server 2005 Express Edition with Advanced Services has been installed manually as described in the 'Install SQL Server 2005 Express Edition with Advanced Services' section of this manual it must be configured correctly so that 963 can be used. Note that this configuration is performed automatically if SQL Server 2005 Express Edition with Advanced Services is installed by the 963's installation program.
Installation 10. On the Start menu point to Programs, point to Microsoft SQL Server 2005, then point to Configuration Tools and click SQL Server Surface Area Configuration. The SQL Server 2005 Surface Area Configuration window is displayed. 11. Click Surface Area Configuration for Features. The Surface Area Configuration for Features dialogue box is displayed. 12. Click xp_cmdshell. The display changes. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Select the Enable xp_cmdshell check box. Click Apply.
Installation 2.14.2 SQL 2005 Full Version 2.14.2.1 Install a Full Version of SQL Server 2005 To install a full version of SQL Server 2005: 1. Install SQL Server according to the instructions supplied by Microsoft®. During the installation you must ensure that the following information is configured. 2. Ensure that the advanced configuration options are not hidden. Install all features. SQL Server instance.
Installation 2.16 Upgrade In most situations upgrading form an earlier version of 963 will simply be a matter of inserting the 963 CD and following the instructions on the screen. the existing version of 963 will be upgraded to the latest version, and the 963's database updated accordingly. There should be no need to relicence 963. In the following circumstances it will be necessary to follow a different installation procedure.
Installation 18. Set the 'Server=' setting in the [DATABASE] section of S2.INI file back to the original setting before it was changed in step (15). 19. Run 963. 2.16.2 Upgrade from 963 v1.x or 962 If 963 v1.x or 962 has been installed and engineered on the PC, it is possible to upgrade to the latest version of 963 without having to re-engineer the system. However a new licence is required to enable 963 to run if upgrading from 962.
Installation 2.16.2.2 Check SQL Queries If upgrading from a version of 963 earlier than v2.1 that uses the VIEWQUERY, QUERYTOTEXTFILE, or PRINTQUERY actions it is recommended that you locate the places they are use and ensure that they work correctly and if necessary fix the problem. This is because the database format used by v2.1 is different from earlier versions of 963 and therefore these actions may now fail. Theses action can be used on schematic pages, alarms actions, and in scheduled events.
Installation 2.16.2.3 Return to the Original 963 System When you upgrade from an earlier version of 963, or 962 a backup of the system is made in a subdirectory of the install directory called 963_backup, or 962_backup. This means that if you decide not to use the latest version of 963 it is possible to return to the original system. To return to the original system: 1.
Installation 8. 9. 10. 11. 12. 13. 14. Click the location to which the licence is to be copied. If moving the licence to a different PC this is the removable media. To create a new folder click Make New Folder. Click OK. The Are you sure? dialogue box is displayed. Click OK. If transferring the licence to a different PC remove the removable media. Run 963 the currently licensed 963. Log on as someone with a PIN level of 99. Press F1 to display the Information Centre. .
Installation This page is intentionally left blank.
Index INDEX Basic Communication Display ...................................................... 17 Check Communications ....................................................................... 17 Check SQL Queries ....................................................................... 25 Communications Check ........................................................................................ 17 Connect ..................................................................................... 17 Port ..........
Index 30 963 Installation Instructions TG201026 Issue 2 09/01/2009
Index 963 Installation Instructions TG201026 Issue 2 09/01/2009 31
Trend Control Systems Limited P.O. Box 34, Horsham, West Sussex, RH12 2YF, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trend-controls.com Trend Control Systems USA 6670 185 th Avenue NE, Redmond, Washington 98052, USA. Tel: (425)897-3900, Fax: (425)869-8445 www.trend-controls.
