Manual

ManualsBrandsTREND ManualsHardwareEM-MPO_STAR3

EM-MPO/STAR3 Installation Instructions TG20771 Issue 1/B 07/04/05

Important: Retain these instructions

Installation Instructions

EM-MPO/STAR3

Electricity Meter

PAG SEL SET

STAR3

Three phase energy analyzer

PAG SEL SET

STAR3

Three phase energy analyzer

STORING

INSTALLATION

H O

-10 °C

+50 °C

20 %RH 90 %RH

It is recommended that the installation should comply

with the HSE Memorandum of Guidance on Electricity

at Work Regulations 1989.

Choose the Location

PAG SEL SET

STAR3

Three phase energy analyzer

H O

-10 °C

+50 °C 20 %RH 90 %RH

PAG SEL SET

STAR3

Three phase energy analyzer

12345678910

PAG SEL SET

STAR3

Three phase energy analyzer

ENC2/S

96 mm 115.4 mm

96 mm

UNPACKING

PAG SEL SET

STAR3

Three phase energy analyzer

PAG SEL SET

STAR3

Three phase energy analyzer

EM-MPO/STAR3

User Manual

TB200774

EM-MPO/STAR3

Installation Instructions

TG200771

EM-MPO/STAR3

> 3 m

Protection Instrument : IP20

Front panel : IP40

100.9 mm

14.5 mm

Summary of content (4 pages)

PAGE 1
Installation Instructions EM-MPO/STAR3 Electricity Meter Important: Retain these instructions UNPACKING EM-MPO/STAR3 User Manual TB200774 EM-MPO/STAR3 Installation Instructions TG200771 STORING +50 °C -10 °C 20 %RH H O 90 %RH It is recommended that the installation should comply with the HSE Memorandum of Guidance on Electricity at Work Regulations 1989. 2 INSTALLATION 1 Choose the Location 14.5 mm STAR3 STAR3 100.
PAGE 2
EM-MPO/STAR3 Installation Instructions INSTALLATION (continued) 2 (b) Mount on Panel Remove clamp from Meter 91 mm (a) Cut hole in Panel 91 mm (d) (c) hole (e) Push on clamp Tighten clamp screws Push meter through 2 screws provided Two part screw terminal, maximum cable cross section 2.
PAGE 3
Installation Instructions EM-MPO/STAR3 INSTALLATION (continued) Connect Measurement Connections (continued) VOLTAGE VL3 1 VL2 2 3 N AL3 4 AL2 5 AL1 6 COM 7 8 S1 L1 S1 L2 Fix ENC2/S 5 CURRENT VL1 NBOX/ENC2/S Installation Instructions Sheet 1, Fixing TG200270 S2 LOAD 4 S2 L3 3 Phase without Neutral (Delta) using 2CTs Connect to ENC2/S red blue RS485 ← → RS232 A RS485 ensure correct polarity B A 6 1 2 B EM-MPO/STAR3 1 2 3 4 5 6 1 2 3 A B OUT 1A 4 5 OUT OUT 1B 2A
PAGE 4
EM-MPO/STAR3 Installation Instructions INSTALLATION (continued) 10 Configure Meter (continued) Pressing PAG again steps on to outputs below OUTPUTS Page PAG Pulse Mode 100 mS Pulse Mode 20 mA Setting 101 SEC PLS 002 SEC PLS Selects 100 mS or 20 mS pulse mode for both outputs Then for each output Out1, Out2 select: kWh total kWh total COG kVArh total kVArh total COG kVAh Then for each output PLS1, PLS2 select units per pulse 1, 10, 100 (e.g.