a) b) c) d) e) f) g) h) a Wall Tile Shower Pan Liquid waterproofing Crack Isolation Tape Cement Board Subfloor Joists b c d f g h e fusion shower pan on wood joists installation guide www.TrendingAccessibility.
Installation Guide 2 for fusion shower pan on wood joists Required Components (included) b) c) f) e) d) a) Fusion Standard Shower Pan b) Tile Drain c) Liquid Waterproofing - 2 gallon bucket (covers approx.
Installation Guide 3 for fusion shower pan on wood joists Stainless Steel Grate Stainless Steel Grate Frame Height Extension Ring (5/8” - 1”) This must be fixed in place using solvent cement. Height Adjustment Ring (1/4” - 5/8” rotate counter-clockwise to increase height - This must be fixed in place using solvent cement. Gasket Clamp (use solvent cement on inner face to achieve seal) Gasket Membrane 3/4” Screws Drain Adapter Flange Fusion Pan Sealing Washers www.trendingaccessibility.
Installation Guide 4 for fusion shower pan on wood joists Step 1 > > > > > > > > > subfloor For optimal performance, it is imperative there is a level surface prior to installation of new Fusion pan. Check existing floor to make sure it is level. If it is not, please correct prior to installation. Step 2 > > > > > > > > > The Fusion Pan is trimmable up to 2” around the perimeter. Place the Fusion pan in desired location and mark the edge of the pan on the subfloor.
Installation Guide 5 for fusion shower pan on wood joists Step 5 > > > > > > > > > Set the pan into place so it does not interfere with the joists. If needed, the pan maybe rotated 180 to make sure there is no interference. Once the pan is set to the desired location, note location of drain and make your connections to the wasteline. Install drain in accordance with current plumbing and building codes.
Installation Guide 6 for fusion shower pan on wood joists Step 9 > > > > > > > > > To prep for permanent installation, remove the Fusion Pan from the surface. Apply a generous amount of construction adhesive to the joists and the plywood floor surface. Step 10 > > > > > > > > Carefully set the Fusion Pan into place. Drill and countersink holes in the Fusion Pan. Using the 2 ½” screws provided, attach the pan.
Installation Guide 7 for fusion shower pan on wood joists Step 13 > > > > > > > > Attach the drain adapter flange to the Fusion Pan. Gasket Clamp Adapter Drain Flange First, set the adapter in place, mark the 4 holes, and pre-drill them with a 1/8” bit. Then, apply a bead of caulk (Recommended: DAP Dynaflex 230) to the underside of the drain adapter flange. Lightly push the flange into place, and screw it down using the four ¾” screws provided. Remove any excess caulk that squeezes out.
Installation Guide 8 for fusion shower pan on wood joists Step 17 > > > > > > > > Using the 5” crack isolation tape provided, cut strips of tape to length, to cover all seams (Corner seams, wall/floor seams, pan/floor joint). Put pieces aside. If you are creating full wet room, you will need to tape any seams throughout the entire room. If you are only waterproofing the shower zone, you will only need to tape the seams up to 2 feet outside the shower area.
Installation Guide 9 for fusion shower pan on wood joists Step 21 > > > > > > > > Gasket Clamp Now attach the clamping ring. Apply primer and solvent cement to inside of clamping ring. Press firmly into position and allow the solvent to set. Drain Adapter Flange It may take about 60 seconds for the cement to form a bond.
Installation Guide 10 for fusion shower pan on wood joists Step 24 > > > > > > > > In order to set the correct height of the grate frame, you may need to use the height extension ring (see diagram to the right). If the height extension ring is required, it will need to be fixed to the height adjustment ring using solvent cement. The grate frame can now be attached to the height adjustment or extension ring, depending on tile thickness.