Quick Installation Guide TEW-436BRM 1.
Table of Contents English 1. Before You Start 2. Hardware Installation 3. Configure The Modem 4. Setting up Encryption 1 1 3 4 7 Troubleshooting Wireless Tips 10 8 Version 11.02.
1. Before You Start Package Contents TEW-436BRM ? ? CD-ROM (User’s Guide) ? Multi-Language Quick Installation Guide ? 1 x RJ-45 Ethernet Cable ? 1 x RJ-11 Telephone Cable ? Power Adapter (12V DC, 1A) System Requirements ? A working ADSL Internet Connection ? A computer with a wired or wireless network adapter properly installed. ? Web Browser: Internet Explorer (5.
Collect Internet Service Provider (ISP) Information During the installation of your Wireless ADSL Modem Router, the Setup Wizard will automatically detect your ISP connection type. If the router cannot detect your ISP connection type, you can manually specify the connection type. Please verify your DSL Internet broadband connection type with your ISP and ensure you have all the information for one of the following connection types: A.
2. Hardware Installation 1. Connect one end of the RJ-45 cable to one of the TEW-436BRM's LAN ports. Connect the other end of cable to the computer's Ethernet port. ADSL ADSL Terminator LAN4 LAN3 LAN2 LAN1 Power 2. Connect one end of the RJ-11 cable to the TEW-436BRM's ADSL port. Connect the other end of the cable to the phone jack. 3. Connect the AC Power Adapter to the TEW436BRM and then to a power outlet. 4. Verify that the following panel lights are on: Power, LAN, and WLAN.
3. Configure the Modem Note: It is recommended that you configure the Modem from a wired computer. 1. Open your web browser, type http://192.168.10.1 in the Address bar, and then press Enter. 2. Enter the User Name and password and then click OK. By default: User name: admin Password: admin Note: User name and Password is case sensitive. 3. Click Setup Wizard.
Note: 1. The example below is for Auto-detect. If the Setup Wizard could not automatically detect your Internet connection, select Manual Selection and input the information using the information provided by your ISP. 2. In the example below, the ADSL connection is PPPoE 4. Select Auto-detect and then click Next. 5. Select the Channel Mode and then click Next. 6. Configure the settings based on information provided by your ISP. Then click Next.
Note: For other connection methods, follow the on screen instructions after you select auto-detect. 7. Please wait while the TEW-436BRM reboots. 8. Check Test Internet Connection, and then click Finish. 9. Verify that the test has completed successfully. Check that the ADSL and Internet LEDs are lit. Then click Close. 10. Open up your browser and enter in a URL (e.g. www.trendnet.com) to verify that you have Internet connection.
4. Setting up Encryption 1. Click Setup -> Wireless -> Security. 2. This example below is WPA2-PSK. Select the following: Encryption: WPA2(AES) WPA Authentication Mode: Personal (Pre-Shared Key) Pre-Shared Key Format: Passphrase Pre-Shared Key: Enter an encryption key. For Example: trendnet Then click Apply Changes. For WPA-PSK or WPA2-PSK, the Pre-Shared Key must be between 8 and 63 ASCII or 64 HEX characters. Make sure to copy down the encryption key.
Troubleshooting I typed http://192.168.10.1 in my Internet Browser's Address Bar, but an error message says “The page cannot be displayed.” How can I get into the TEW-436BRM's web configuration page? 1. Check your hardware settings again by following the instructions in Section 2. 2. Make sure the Power, LAN and WLAN lights are lit. 3. Make sure your TCP/IP settings are set to Obtain an IP address automatically (see the steps below). Windows Vista 1.
The Modem does not auto-detect my DSL connection. What should I do? 1. Verify that your DSL account is activated. 2. Make sure all the cables are properly connected (see Section 2). 3. In Section 3, select manual selection in the Setup Wizard and configure the Modem based on information provided by your ISP. All the settings are correct, but I cannot make a wireless connection to the Modem. What should I do? 1. Double check that the Wireless LED on the Modem is lit.
Wireless Tips The following are some general wireless tips to help minimize the impact of interference within an environment. Assign your network a unique SSID Do not use anything that would be identifying like “Smith Family Network”. Choose something that you would easily identify when searching for available wireless networks. Do not turn off the SSID broadcast The SSID broadcast is intended to be on and turning it off can cause connectivity issues.
2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. 3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall.
GPL/LGPL General Information This TRENDnet product includes free software written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. The details of the GNU GPL and LGPL are included in the product CD-ROM. Please also go to (http://www.gnu.org/licenses/gpl.
GPL/LGPL informações Gerais Este produto TRENDnet inclui software gratuito desenvolvido por terceiros. Estes códigos estão sujeitos ao GPL (GNU General Public License) ou ao LGPL (GNU Lesser General Public License). Estes códigos são distribuídos SEM GARANTIA e estão sujeitos aos direitos autorais dos desenvolvedores. TRENDnet não presta suporte técnico a estes códigos. Os detalhes do GNU GPL e do LGPL estão no CD-ROM do produto. Favor acessar http://www.gnu.org/licenses/gpl.txt ou http://www.gnu.
