Anleitung zur Schnellinstallation TEW-637AP 3.
Table of Contents Deutsch 1. Bevor Sie anfangen 2. Installation der Hardware 1 1 2 Troubleshooting 7 Version 04.19.
1. Bevor Sie anfangen Packungsinhalt ŸTEW-637AP ŸMehrsprachige Installationsanleitung ŸCD-ROM (Dienstprogramm und Bedienungsanleitung) ŸNetzteil (12V Gleichstrom, 0.5A) ŸNetzwerkKabel (0.6m / 2ft.) Systemanforderungen ŸWebbrowser wie der Internet Explorer (6 oder Super), Firefox (2.0 oder höher), Opera, Chrome, Safari ŸComputer mit korrekt installiertem Netzwerk- oder drahtlosem Adapter ŸRouter mit einem freien LAN-Port.
2. Installation der Hardware Hinweis: 1. Suchen Sie nach einem optimalen Einsatzort für den Access Point. Der beste Standort eines Access Points liegt normalerweise im Zentrum Ihres drahtlosen Netzwerks. 2. Deaktivieren Sie Ihre Antivirus- und Firewall-Programme, bevor Sie die Hardware-Installation beginnen. Für Benutzer von Windows 1. Legen Sie die Dienstprogramm-CD in das CD-ROM-Laufwerk Ihres Computers. 2. Klicken Sie auf Run Setup.exe (setup.exe ausführen). (Windows 7/Vista only) 3.
. Verbinden Sie einen LAN-Port Ihres Routers über das mitgelieferte RJ-45-Kabel mit dem LAN-Port des TEW-637AP. Klicken Sie dann auf Next (Weiter). 6. Verbinden Sie einen LAN-Port des Routers über ein RJ-45-Kabel mit dem Ethernet-Port Ihres Computers. 7. Verbinden Sie das Netzteil mit dem Access Point und stecken Sie es in eine Steckdose. Klicken Sie dann auf Next (Weiter). 8. Wählen Sie den TEW-637AP aus der Liste aus und klicken Sie auf Configure (Konfigurieren). 9.
10. Markieren Sie Dynamic IP Address Configuration (Konfiguration der dynamischen IP-Adresse) und klicken Sie auf Next (Weiter). 11. Markieren Sie Manual setup (Manuell einrichten) und klicken Sie auf Next (Weiter). 12. Geben Sie eine SSID ein und klicken Sie auf Next (Weiter). Standardmäßig lautet die SSID TRENDnet637.Die SSID ist der Name Ihres drahtlosen Netzwerks (z.B. des drahtlosen Routers oder Access Points). Geben Sie einen eindeutigen Namen ein.
Hinweis: 1. Um Ihr Netzwerk vor unbefugten Zugriffen zu schützen, sollten Sie die drahtlose Verschlüsselung aktivieren. 2. Das folgende Beispiel gilt für die WPA2-PSK(AES)-Verschlüsselung. Wählen Sie WPA-PSK oder WPA2-PSK nur dann aus, wenn Ihre drahtlosen Adapter tatsächlich WPA bzw. WPA2 unterstützen. Markieren Sie andernfalls WEP. 3. Die WEP Verschlüsselung unterstützt nur 802.11b/g Geschwindigkeiten von bis zu 54Mbps. 4.
17. Klicken Sie auf Next (Weiter), um die Einstellungen zu übernehmen. 18. Klicken Sie auf Exit. 19. Klicken Sie zum Abschluss auf Yes (Ja). Hinweis: Eine Anleitung zur Verbindung eines drahtlosen Computers mit dem TEW-637AP finden Sie in Antwort 1 im Abschnitt „Problembehandlung“. Die drahtlose Verbindung ist jetzt vollständig konfiguriert.
Troubleshooting 1. All the settings are correct, but I can not make a wireless connection to the Access Point. 1. Double check that the wireless LED on the Access Point is lit. 2. Power cycle the Access Point. Unplug the power to the Access Point. Wait 15 seconds, then plug the power back in. 3. Contact the manufacturer of your wireless network adapter. Make sure the wireless network adapter is configured with the proper SSID. The default SSID of the Access Point is TRENDnet637.
5. I followed the Quick Installation Guide and setup a new password. When I log in to the browser configuration an access error message appears. What should I do? If the password was changed and you don't remember it, you need to reset the TEW-637AP. To reset the TEW-637AP, power up the unit and wait 30 seconds for the unit to boot up. Then take a pin or paper clip and press the reset button for 15 seconds, then let go. The reset button is located on the bottom of the TEW-637AP.
Wireless Tips The following are some general wireless tips to help minimize the impact of interference within an environment. Assign your network a unique SSID Do not use anything that would be identifying like “Smith Family Network”. Choose something that you would easily identify when searching for available wireless networks. Do not turn off the SSID broadcast The SSID broadcast is intended to be on and turning it off can cause connectivity issues.
3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal. 4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapter's site survey tool to determine the best antenna orientation for your wireless devices. 5.
Copyright © 2011. All Rights Reserved. TRENDnet.