User's Guide
Table Of Contents
- Table of Contents
- Product Overview
- Router Setup
- Wireless Networking and Security
- Basic
- ADvanced
- Change your router IP address
- Set up the DHCP server on your router
- Set up DHCP reservation
- Manually configure your Internet connection
- Clone a MAC address
- Add static routes to your router
- IPv6 Internet Connection Settings
- Prioritize traffic using QoS (Quality of Service)
- Advanced wireless settings
- Set your router date and time
- Create schedules
- Access Control
- Open a device on your network to the Internet
- Enable/disable Application Layer Gateways (ALG)
- Enable/disable UPnP on your router
- Using External USB Storage
- Print Share Utility Installation
- Router Maintenance & Monitoring
- Change your router login password
- Change your device name
- Change your device URL
- Identify your network on the Internet
- Allow remote access to your router management page
- Reset your router to factory defaults
- Router Default Settings
- Backup and restore your router configuration settings
- Upgrade your router firmware
- Reboot your router
- Allow/deny ping requests to your router from the Internet
- Check the router system information
- Router Management Page Structure
- Technical Specifications
- Troubleshooting
- Appendix
© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-818DRU
20
• Wireless Name (SSID): This acronym stands for Service Set Identifier and is the
name of your wireless network. It differentiates your wireless network from others
around you. It is recommended to use a different name from your primary wireless
network to a name that you can easily identify and differentiate from the primary.
You can reference your guests to access this network instead of the primary.
• Internet Access Only: By default, the option is checked to allow guests to only
access the Internet and restrict access to your local LAN network. Please note that
unchecking this option will open access to local LAN network to guests.
• Wireless Client Isolation: Checking this option will restrict guests from
communicating with each other over the guest network such as share files.
5. Under Security Policy, you can apply a different wireless security type and key to the
guest network. Please refer to page 15 to find out about different security types and
page 16 for wireless security configuration.
Advanced Guest Network Settings
Wireless (2.4GHz or 5GHz) > Guest Network>Advanced Guest Network Settings
At the bottom of the guest network page, you can click the “Advanced Guest Network
Settings” to configure the additional guest network options such as the guest network
interface IP address, DHCP server IP address range, and DHCP reservation.
Review the Advanced Guest Network settings, click Apply when finished.
In most cases, you do not need to change your guest network IP address settings.
Typically, the router IP address settings only needs to be changed, if you plan to use
another router in your network with the same IP address settings, if you are connecting
your router to an existing network that is already using the IP address settings your
router is using, or if you are experiencing problems establishing VPN connections to
your office network through your router.
• IP Address – Enter the new guest network IP address.
(e.g. 192.168.100.1)
• Subnet Mask – Enter the new guest network subnet mask.
(e.g. 255.255.255.0)
Note: If you are not encountering any issues or are not faced with one of the cases
described above or similar, it is recommended to keep your guest network sIP address
settings as default. The guest network IP address settings should different from your
local LAN network IP address settings (Default: 192.168.10.1 / 255.255.255.0)
Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to
automatically assign an IP address to each computer or device on your guest network.
The DHCP server is enabled by default on your router. It is recommended to leave this
setting enabled.
• DHCP Server – Enable or Disable the DHCP server.
• DHCP Start IP – Changes the starting address for the DHCP server range. (e.g.
192.168.20.20)
• DHCP End IP – Changes the last address for the DHCP server range. (e.g.
192.168.20.30)
• Lease Time – Enter the lease time in seconds.
DHCP (Dynamic Host Configuration Protocol) reservation (also called Static DHCP) allows
your router to assign a fixed IP address from the DHCP server IP address range to a
specific device on your guest network.