User's Guide
Table Of Contents
- Table of Contents
- Product Overview
- Router Setup
- Wireless Networking and Security
- Basic
- ADvanced
- Change your router IP address
- Set up the DHCP server on your router
- Set up DHCP reservation
- Manually configure your Internet connection
- Clone a MAC address
- Add static routes to your router
- IPv6 Internet Connection Settings
- Prioritize traffic using QoS (Quality of Service)
- Advanced wireless settings
- Set your router date and time
- Create schedules
- Access Control
- Open a device on your network to the Internet
- Enable/disable Application Layer Gateways (ALG)
- Enable/disable UPnP on your router
- Using External USB Storage
- Print Share Utility Installation
- Router Maintenance & Monitoring
- Change your router login password
- Change your device name
- Change your device URL
- Identify your network on the Internet
- Allow remote access to your router management page
- Reset your router to factory defaults
- Router Default Settings
- Backup and restore your router configuration settings
- Upgrade your router firmware
- Reboot your router
- Allow/deny ping requests to your router from the Internet
- Check the router system information
- Router Management Page Structure
- Technical Specifications
- Troubleshooting
- Appendix
© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEW-818DRU
24
Note: The DHCP address range will change automatically to your new router IP
address settings so you do not have to change the DHCP address range manually to
match your new router IP address settings.
• IP Address: Enter the new router IP address. (e.g. 192.168.200.1)
• Subnet Mask: Enter the new router subnet mask. (e.g. 255.255.255.0)
Note: You will need to access your router management page using your new
router IP address. (e.g. Instead of using the default
http://192.168.10.1 your new
router IP address will use the following format using your new IP address
http://(new.ipaddress.here)
to access your router management page. You can
also use the default login URL
http://TEW-818DRU
Set up the DHCP server on your router
N Advanced > Setup > LAN Setting
Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to
automatically assign an IP address to each computer or device on your network. The
DHCP server is enabled by default on your router. If you already have a DHCP server on
your network, or if you do not want to use your router as a DHCP server, you can disable
this setting. It is recommended to leave this setting enabled.
1. Log into your router management page (see “
Access your router management page”
on page 17).
2. Click on the Advanced tab.
3. Click on the Setup section and click on LAN Setting.
3. Review the DHCP Server settings. Click Apply to save settings.
• DHCP Server: Enable or Disable the DHCP server.
• DHCP Start IP: Changes the starting address for the DHCP server range.
(e.g.192.168.10.20)
• DHCP End IP: Changes the last address for the DHCP server range. (e.g.
192.168.10.30)
Note: The Start IP and End IP specify the range of IP addresses to automatically
assign to computers or devices on your network.
• DHCP Lease Time: Click the drop-down list to select the lease time.
Note: The DHCP lease time is the amount of time a computer or device can keep an
IP address assigned by the DHCP server. When the lease time expires, the computer
or device will renew the IP address lease with the DHCP server, otherwise, if there is
no attempt to renew the lease, the DHCP server will reallocate the IP address to be
assigned to another computer or device.
Set up DHCP reservation
Network > LAN Setting
DHCP (Dynamic Host Configuration Protocol) reservation (also called Static DHCP) allows
your router to assign a fixed IP address from the DHCP server IP address range to a
specific device on your network. Assigning a fixed IP address can allow you to easily
keep track of the IP addresses used on your network by your computers or devices for