1. Attach the wall mount plates to THSG104 using the provided screws. 2. Mount the splatter onto the desired wall location. + turmoil off the power before connecting any mauled or wires. The adjustable output voltages (12, 16, 24, 48V DC) and corresponding DIP switch settings are listed on the device label. Check the voltage requirements of the device you are powering and set the DIP switches accordingly. » Calculate the maximum possible current In each power wire and comment wire.
Covering your Device 1. Install the included terminal block onto TI-SG104. 2. Insert the Negative/Positive DC res Into V1 output terminals. 3. Conn act the other and of the DG wires to the powered device. Mote: Polarities must match. 4. Tighten the terminal block screws to secure the power connection. 5. Configure the Ultra PoE Sp litter's DIP switch to meet your application cottage requirements. 6. Connect TI-5G104 to an Ultra PoE PSE to power on the device. 7.
3. Installation du matériel Le séparateur Nitra PoE peut être placé sur un bureau, sur un mur ou fixé sur un rail DIN. Instructions de fixation rail IN 1. Axez la support de fixation rail DIN & Auto-injecteur Poe. 2. Installez le appareil en face du rail DIN et accrochez e support de fixation au-dessus du rail 3. Caltes pivoter ls séparateur vers Is bas en direction du rail afin de le fixer 4 son emplacement. Un clic vous avertira lorsqu’il sst en place. P RS Installation tu appareil Retirer le appareil 4.
Instructions de fixation murale 1. Fixez les plaques de fixation murale au TI-SG104 & Aide des vis fournies. 2. Monter lo paradeur & 'emplacement souhait aur le mur. Consignes de sécurité » Coupez le courant savart de brancher quelque module ou câble que ce soit. Les tensions de ‘sortie réglables {12, 18, 24, 48V DC) et les réglages des Intsrruptours DIP correspondante sont Indiqués sur I'Stiquette de Appareil.
3. Instalación del harreare B divisor Otra PoE se puede colocar en un escritorio, o morrearse en una pared o en DIN-Raíl. Instrucciones de montaje en DIN-Hall 1.Acople e soporte de montaje en DIN-Raíl al inyector Poeta. 2. Coloque fa unidad en frente del DIN-Hall y enganche el soporte de montaje en el carril. 3. Gire ol divisor para abajo lacha el carril hasta dejarlo bloquea. Escuchar un clic ‘cuando quede fijado, P RS Montando a unidad Soltando Ia unidad 4.
s 3. Instalação do hardware 0 plotter Ultra POE pode ser colocado em um desimpede, na parede ou montado em ur trilho DI, Instruirdes de montagem em trilho DIN 1. Fixe ¢ suporte do trilha DIN no injetor Poeta. 2. Posicione o unidade na frente do trilho DIN ¢ enganche o suporte de corretagem na parte superior do trilho. 3. Gire o aplicante para baixo sm diretório ao trilho para travá-lo no lugar. Vos saber quo els sustém ‘seguro quando ouvir um clique. A Remontagem do unidade X Liberatório do unidade 4.
Declaration of Conformity TREND NET Manufacturer’s Name and Address Trend, Inc. 20675 Manhattan Place Torrance, CA 90501 USA Sequestrate 156 2587 W ‘The Hague The Netherlands. Product Information: Model Number: TI-SG104 Industrialist Gigabit UPON Splutter Trend net q3 Trend net hereby declare that the product ks In compliance with the essential requirements and other relevant provisions under our sole responsibility.
