Quick Installation Guide

ManualsBrandsTRENDnet ManualsNetwork EquipmentPowerline 500 AV Adapter with Built-In Outlet

TPL-402E

TPL-402E2K

1.01

Summary of content (12 pages)

PAGE 1
Quick Installation Guide TPL-402E TPL-402E2K 1.
PAGE 2
Table of Contents English 1. Before You Start 2. How to Install 3. LEDs and Buttons 1 1 2 5 Troubleshooting 6 Version 03.16.
PAGE 3
1. Before You Start Package Contents ŸTPL-402E/TPL-402E2K ŸCD-ROM (Utility and User's Guide) ŸMulti-Language Quick Installation Guide ŸNetwork Cable (1.5m/5ft) System Requirements ŸCD-ROM drive ŸA Desktop or Laptop PC with Network Adapter Installed ŸExisting 10/100/1000Mbps wired network when TPL-402E is used as a bridge device ŸAdditional HomePlug ® AV or IEEE 1901 compliant powerline adapter (e.g.
PAGE 4
2. How to Install Powerline Networking Solution 500Mbps Powerline AV Adapter Kit (TPL-402E) Internet Gigabit Powerline The example diagram shows a typical powerline network configuration in a home environment with 3 powerline adapters installed in different rooms. The orange line represents the powerline connectivity established through your home's electrical system and the blue lines represent Cat.
PAGE 5
Below is an example showing how to create a Powerline network using the TPL-402E/TPL-402E2K and your existing router to share Internet. 1. Plug a TPL-402E into an available power outlet. This TPL-402E should be located within the reach of the router's network cable. Outlet 2. Connect a network cable from the TPL-402E to an available LAN network port on your router (e.g. TEW-673GRU). 3. Plug a second TPL-402E into an available power outlet where your remote computer or network appliances (e.g.
PAGE 6
4. Connect a network cable from the second TPL-402E's network port into the network port on your remote computer or network appliance (e.g. Game Console, Blu-ray player, IP set top box, network enabled TV, etc.). Outlet 5. Verify that the PWR (Power), PL (Powerline) and ETH (Ethernet Link/Act) LEDs are on for both TPL-402E adapters.
PAGE 7
3. LEDs and Buttons PWR (Power) PL (Powerline) ETH (Gigabit Ethernet Link/Act) The Gigabit Ethernet/Network Port and Reset buttton are located at the bottom of the device. Reset Button Gigabit + Ethernet / Network Port Sync Note: 1. Please refer to the User's Guide on the TPL-402E/TPL-402E2K's User's Guide CD for detailed explanations of each LED and button. 2. The following factors may affect the powerline network’s connection quality: a.
PAGE 8
Troubleshooting 1. I have verified that my Powerline device is connected to my workstation, but I cannot detect other Powerline devices. What should I do? 1.Verify that you are using Cat. 5, Cat. 5e or Cat. 6 Ethernet network cables for each TPL-402E adapter. 2.Verify that the power outlet of the TPL-402E/TPL-402E2K is plugged into is on the same electrical power distribution and/or circuit breaker box. 3.
PAGE 9
Windows Vista 1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Manage Network Connections and then right-click the Local Area Connection icon and then click Properties. 2. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Obtain an IP address automatically. Windows XP/2000 1. Go into the Control Panel, double-click the Network Connections icon and then right-click the Local Area Connection icon and then click Properties.
PAGE 10
PAGE 11
Description of Modes Erp (EuP) Operation: Standby Mode The EUT has no external mechanical switch and uses an internal program to control active and standby modes. Disconnect the Ethernet cables from the device Ethernet ports, and after 3 minutes, the device will enter standby mode. The Power (PWR) LED will flash every 15 seconds to indicate that the device is currently in standby mode.