TRENDnet User’s Guide Table of Contents Contents Product Overview ................................................................................ 2 Troubleshooting .................................................................................36 Package Contents .......................................................................................................... 2 Features .........................................................................................................................
TV-IP262PI TRENDnet User’s Guide Features Product Overview The Megapixel PoE Dome Internet Camera with IR (model TV-IP262PI) is an indoor, enterprise class surveillance camera capable of transmitting H.264 video at up to 1280 x 1024 resolution. View and manage the tamper resistant dome IP camera from any computer with an internet connection. Manually pan the camera side-to-side350 degrees and tilt it up-and-down 70 degrees to fix its final viewing position.
TV-IP262PI TRENDnet User’s Guide Product Hardware Features Reset: Press and hold the reset button for five seconds to reset the camera to factory default settings. Rear Panel View Front Panel View Power Connector: Connect the provided power adapter to supply power to the camera for non-PoE installation. SD Card Slot: Insert a memory card for expansion of storage. Ethernet/PoE Connector: Connect the provided network cable (RJ-45 type) to Ethernet/PoE port for wire or PoE connection.
TV-IP262PI TRENDnet User’s Guide Application Diagram Inside Component LED indicators Power: Indicate the camera is powered on with the steady amber light. - Link: Indicate the camera’s network connectivity with the flashing green light. © Copyright 2012 TRENDnet. All Rights Reserved.
TV-IP262PI TRENDnet User’s Guide Installation Hardware Installation 3. Secured the camera to the location with three screws. The camera can be mounted to the ceiling surface directly by following the steps below: 4. Before put the Dome cover back, adjust the lens assembly by the following steps: 1. 2. Remove the Dome cover by unscrewing the four screws. Tilt the camera lens to a proper position by losing the screws () and then swinging the adjustable base ( ).
TV-IP262PI TRENDnet User’s Guide Camera Installation 1. 2. 3. Write down the MAC ID of the camera 4. Connect one end of the power adapter into the Power Connector, then click on Next. Please click Next if you are using the PoE injector or switch. Insert the Installation CD-ROM into your computer’s CD-ROM drive to initiate the Auto-Run program. lick the Install Camera. © Copyright 2012 TRENDnet. All Rights Reserved.
TV-IP262PI TRENDnet User’s Guide 5. Connect a network cable to the camera’s network port and then to your router. If you are using PoE, please ensure the cable is connected to a PoE switch or PoE injector. 7. The founded cameras will show on the screen. The camera already selected by default if you have only one camera installed. If you have more than one camera in the same Network, you will need to identify the camera by the MAC ID. 8. You MUST change the default password of the camera.
TRENDnet User’s Guide 9. Type in the new and confirm the new password by entering the password twice. TV-IP262PI 11. You can also click Finish to exit the program or click Home return to the main screen. 10. Click TV-IP262P to access to the camera web page. © Copyright 2012 TRENDnet. All Rights Reserved.
TV-IP262PI TRENDnet User’s Guide Starting Camera Finder The camera comes with a conveniently utility, IPSetup, which is included in the Installation CD-ROM, allowing you to search the camera on your network easily. 1. 2. Click the Camera Finder (IPSetup) from the Auto-Run menu screen. Then the IPSetup Wizard will appear. Click Install to install the utility. 3. When the Completing the IPSetup Setup Wizard appears, click Finish.
TV-IP262PI TRENDnet User’s Guide 4. 5. After installing the IPSetup utility, the application is automatically installed to your computer, and creates a folder in Start\Program\TRENDnet\IPSetup. Click Start>Programs>TRENDnet>IPSetup, and then click IPSetup. - Access Camera: Open Web browser to view camera . - Camera Display Area: By default, the IP setting on the Camera is set to DHCP. If you have DHCP server, the camera will automatic get the IP address from DHCP server.
TRENDnet User’s Guide Configuration TV-IP262PI After you login into the Web Configuration of the camera, the main page will appear as below: Viewing Camera Basic Function Open the Web browser on your computer (example showed in the User’s Guide is based on the Internet Explorer). Type the default IP address (192.168.10.30) or the IP address found by IPSetup in the Address bar, and then press [Enter].
TV-IP262PI TRENDnet User’s Guide Live View/Setup Switch: Click the button to configure the camera. Click the view image. button to return to the Main screen to view the live * If you are using Microsoft 7/Vista platform, you may not be able to find the recorded files by Snapshot or Manual Record. You will need to disable the protected mode of Security in the IE browser before recording a video file or taking a snapshot. Please follow the below steps: 1.
TV-IP262PI TRENDnet User’s Guide The Web Configuration contains the settings that are required for the camera in the left menu bar, including Smart Wizard, Basic, Network, Video/Audio, Event Server, Motion detect, Event Config, Tools, SD Card, and Information. Smart Wizard The camera’s Smart Wizard lets you configure your camera easily and quickly. The wizard will guide you through the necessary settings with detailed instructions on each step. To start the wizard, click Smart Wizard in the left menu bar.
TV-IP262PI TRENDnet User’s Guide Confirm Settings Basic The last step shows the configuration of your camera. When you confirm the settings, click Apply to finish the wizard and reboot the camera. Otherwise, click Prev to go back to the previous step(s) and change the settings; or click Cancel to end the wizard and discard the changes. The Basic menu contains three sub-menus that provide the system settings for the camera, such as the Camera Name, Location, Date & Time, and User management.
TV-IP262PI TRENDnet User’s Guide Basic: This item allows you to assign the camera name and location information. Camera Name: Enter a descriptive name for the camera, which is helpful to identify the camera easily while multiple cameras are connected within the network. Location: Enter a descriptive name for the location where is monitored by the camera. Language Default: Select the displayed language as default.
TV-IP262PI TRENDnet User’s Guide NOTE: The “General User” is allowed to access the camera and control the Function buttons on the Main screen of the Web Configuration.; the “Guest” can only view the live view image from the Main screen while accessing the camera. Only the “Administrator” is allowed to configure the camera through the Web Configuration. Network The Network menu contains two sub-menus that provide the networking settings for the camera, such as the IP Setting, DDNS Setting, and IP Filter.
TV-IP262PI TRENDnet User’s Guide Network >> Network Gateway default setting is 192.168.10.1. Primary/ Secondary DNS DNS (Domain Name System) translates domain names into IP addresses. Enter the Primary DNS and Secondary DNS that are provided by ISP. PPPoE: Select this option when you use a direct connection via the ADSL modem. You should have a PPPoE account from your Internet service provider. Enter the User Name and Password. The camera will get an IP address from the ISP as starting up.
TV-IP262PI TRENDnet User’s Guide Network >> Advanced RTSP RTSP Streaming: The camera supports three levels of RTSP access. The default RTSP Port is 554. Disable sic Digest RTSP link does not require authentication. No username/password required. RTSP link prompts for authentication. Username/password are transmitted in plain text. RTSP link prompts for authentication. Username/password are encrypted during data transmission. TRENDnet recommends using RSTP Digest authentication method.
TV-IP262PI TRENDnet User’s Guide Network >> IP Filter finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. For example, when you enter 192.168.0.50 in Start IP Address and 192.168.0.80 in End IP Address, the user whose IP address located within 192.168.0.50 ~ 192.168.0.80 will not be allowed to access the camera. IPv6: Enter the IP Address that is not allowed to access the camera.
TV-IP262PI TRENDnet User’s Guide Video & Audio >> Camera AE Control: Select AE (Auto Exposure) speed as Fast, Normal or Slow. Mode Frequency AE Control (Day Time) AE Control (Night Time) min. shutter speed min. shutter speed Fast Normal Slow Fast Normal Slow 60Hz 1/120s 1/60s 1/30s 1/120s 1/60s 1/30s 50Hz 1/100s 1/50s 1/25s 1/100s 1/50s 1/25s 60Hz 1/120s 1/60s 1/15s 1/120s 1/60s 1/15s 50Hz 1/100s 1/50s 1/12.5s 1/100s 1/50s 1/12.
TV-IP262PI TRENDnet User’s Guide •H.264 Video Resolution: Select the desired video resolution from the four formats: SXGA, VGA, QVGA, QVGA and 720P. The higher setting (SXGA) obtains better video quality while it uses more resource within your network. Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. Frame Rate: Select a proper setting depending on your network status.
TV-IP262PI TRENDnet User’s Guide In the Image File option, click Browse to select the image file from your computer, and then click Upload. You can click Preview to check the image size and adjust the image position before clicking Upload. The preview image area is displayed with red dotted line. If you want to remove the preview image before uploading, click Delete.
TV-IP262PI TRENDnet User’s Guide HTTP Notify For Motion Trigger Event Server Setting >> FTP Send the query parameter via an HTTP notification when an event is triggered. Host: Enter the IP of the HTTP server Port: Enter the Port number of the HTTP server User Name: Enter the username of the HTTP server Password: Enter the password of the HTTP server Query: Enter the query parameter for the request if necessary Example: Host: 192.168.10.1 Port: 80 Query: xxx.
TV-IP262PI TRENDnet User’s Guide Event Server Setting >> Email Authentication Mode: Select None to disable the authentication feature, or select SMTP and then enter the User Name and Password according to the mail server configuration. Sender User Name: Enter the user name to login the mail server. Sender Password: Enter the password to login the mail server. Receiver #1 Email Address: Enter the first email address of the user who will receive the email.
TV-IP262PI TRENDnet User’s Guide Path: Assign the path for uploading the files on the Network Storage server. For example, Test. User Name: Enter the user name to login into the Network Storage server. Password: Enter the password to login into the Network Storage server. Split By: When the file is too large to upload smoothly, use this option to split it by selecting File Size or Recording Time.
TV-IP262PI TRENDnet User’s Guide Event Config The Event Config menu contains five sub-menus that provide the commands to configure event profiles. Snapshot/Recording Subfolder: You can assign a given subfolder to each new captured file. Otherwise, leave this option blank to use the default setting. Network Storage Recording Time Per Event: Limit the recording time while you are using the Network Storage solution.
TV-IP262PI TRENDnet User’s Guide Profile Name: Display the profile name that you select in the Schedule Profiles list. Weekdays: Select the weekday(s) that you want to separately assign in the schedule profile. The weekday that has been assigned will be displayed with green color. Time List: Display the time period that you have assigned within the selected weekday.
TV-IP262PI TRENDnet User’s Guide Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera. Update Firmware: You can upgrade the firmware for your camera once you obtained a latest version of firmware. Current Firmware Version: This item displays the current firmware version. Select the firmware: Click Browse to locate the backup file and then click Update.
TV-IP262PI TRENDnet User’s Guide SD Card >> SD Card Setting SD Card >> File Manager The File Manager menu allows you to download files from the SD card. Simply click the Download button to start downloading files. SD Card Dismount: Click Dismount to safely remove the SD card that is installed in the camera. SD Card Information: Displays the information of the installed SD card, including the Total space and Free space.
TV-IP262PI TRENDnet User’s Guide Device Info Information >> Device Info Display the Basic, Video & Audio, and Network settings of the camera. The Information menu displays the current configuration and events log of the camera. Information >> System Log The Logs table displays the events log recorded by the system. © Copyright 2012 TRENDnet. All Rights Reserved.
TV-IP262PI TRENDnet User’s Guide How to setup/access the camera behind a Router 4. Open another web browser and go to your Router’s Web Configuration page. (In the example, TRENDnet’s TEW-651BR Wireless N router is used) You can either setup the Dynamic DNS connection via camera itself or your home router. An account from any of the listed DDNS providers is required prior to this operation. Configure DDNS on your Camera 1. Go to Camera’s DDNS Setting page, click Enable to activate the feature.
TV-IP262PI TRENDnet User’s Guide 5. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg. CameraName) Protocol: Select TCP Private Port: The HTTP port that you assign on your Camera. Public Port: The port used on remote side to access to your Camera. LAN Server: The local IP address of your Camera. 6. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber 7. Camera’s login page will appear.
TV-IP262PI TRENDnet User’s Guide 2. Login to your router’s web configuration page. 3. Find the Dynamic DNS configuration section. 5. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg. Camera Name) Protocol: Select TCP Private Port: The HTTP port that you assign on your Camera. Public Port: The port used on remote side to access to your Camera. LAN Server: The local IP address of your Camera. 4.
TV-IP262PI TRENDnet User’s Guide Technical Specifications Camera General SD Slot Sensor: 1/4” Megapixel CMOS sensor Max. Resolution: 1280 x 1024 pixels Board Lens Focal Length: 3.58 mm Aperture (F/No): F2.0 +/- 5% Minimum illumination: 0 Lux (night vision) Viewing Angle Hardware Network IEEE 802.3u 10/100Mbps Fast Ethernet IEEE 802.3af PoE LED Power, Link / Act (can turn off LEDs) Reset Button Reboot or restore to factory default Power Consumption 7 watts max. Power Input: 100 ~ 240V AC , 0.
TV-IP262PI TRENDnet User’s Guide Requirement Management Interface Settings Internet Explorer 7.
TV-IP262PI TRENDnet User’s Guide Port Settings HTTP port: 80 (default) Troubleshooting RTSP port: 554 (default) 1. The Power LED and Ethernet Activity LED do not light up. The power supply or camera might be faulty. Check that the connection to both the power source and the terminal on the back of the camera are secure and that you are using the provided power supply. If the camera is otherwise functioning correctly, the LEDs might have been disabled in the configuration.
TV-IP262PI TRENDnet User’s Guide Make sure that the Network Camera isn’t conflicting with any Web server you may have running on your network. The default router setting might be a possible reason. Check that the configuration of the router settings allow the Network Camera to be accessed outside your local LAN. 4.
TRENDnet User’s Guide Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TV-IP262PI – 3 Years Limited Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
Limited Warranty TRENDnet User’s Guide Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license. V1.0R / 10.03.
