P REFACE Thank you for purchasing the TV-IP322P SecurView™ Outdoor PoE Megapixel Day/Night Internet Camera, a standalone system that can be connected directly to an Ethernet or Fast Ethernet network. The camera is equipped with a 2-megapixel CMOS sensor, allowing you to capture high quality image with the resolution of up to 1280 x 1024. Additionally, the camera features the IR (Infrared) LEDs and ICR function (IR Cut Filter).
This Advanced Installation Guide provides you with the instructions and illustrations on how to use your camera, which includes: Chapter 1 Introduction to Your Camera describes the features of the camera. You will also know the components and functions of the camera. Chapter 2 Hardware Installation helps you install the camera according to your application environment. You can use this camera at home, at work, at any where you want.
Contents PREFACE CHAPTER 1 INTRODUCTION TO YOUR CAMERA 1.1 1.2 1.3 1.4 CHECKING THE PACKAGE CONTENTS ............................................. 5 GETTING TO KNOW THE CAMERA ................................................. 6 FEATURES AND BENEFITS ............................................................ 9 SYSTEM REQUIREMENT ............................................................ 12 CHAPTER 2 HARDWARE INSTALLATION 2.1 2.2 2.3 2.4 ASSEMBLING THE CAMERA MOUNTING BRACKET ........................
4.8 4.9 4.10 4.11 4.12 EVENT CONFIGURATION ........................................................... 58 TOOLS ................................................................................... 64 RS-485................................................................................. 66 SETTING UP THE SD CARD......................................................... 70 INFORMATION ........................................................................ 72 CHAPTER 5 SECURVIEW™ PRO SOFTWARE 5.1 5.
C HAPTER 1 INTRODUCTION TO YOUR CAMERA 1.1 Checking the Package Contents Unpack the package and check the items contained in the package carefully. You should have the following: 1 x TV-IP322P 1 x Multi-Language Quick Installation Guide 1 x CD-ROM (Utility & User’s Guide) 1 x Desiccant ** 2 x GPIO Connector 1 x Spiral Cable Wrap 1 x Camera Mounting Bracket Kit* 1 x Power Adapter (12V DC, 1.
1.2 Getting to Know the Camera The Camera and the Shield Shield* is used to protect the camera during inclement weather. Lens Assembly with IR LEDs Connectors Power, Audio, Mic, GPIO, LAN Camera Stand * There are various positions of screw hole on the shield, allowing you to move the shield forward/backward according to your needs. For example, it will protect the camera lens well during rainy day by adjusting the shield forward.
The Connectors The camera's connectors are collected into a bundle of cable on the back panel of the camera, allowing you to connect the external devices in a well-ordered way while you are installing the camera onto the wall (or ceiling). Power: Connects the power adapter to supply power to the camera. GPIO: Connects the external device that features additional controlling function, such as motion detection, event triggering, alarm notification, and a variety of external control functions.
LAN: Plugs the provided Ethernet cable to connect to your local area network (LAN). The LAN port of the camera supports the NWay protocol so that the camera can detect the network speed automatically.
1.3 Features and Benefits H.264/MPEG4/MJPEG Multi-codec Supported The camera provides you with excellent images by the H.264/MPEG4/ MJPEG multi-codec selectable technology, allowing you to adjust image size and quality, and bit rate according to the networking environment. High Resolution Surveillance Equipped with a megapixel CMOS sensor, the high performance camera is designed for your professional surveillance and security applications. The image resolution is up to 1280 x 1024.
Remote Control Supported By using a standard Web browser or the bundled SecurView™ Pro software application, the administrator can easily change the configuration of the camera via Intranet or Internet. In addition, the camera can be upgraded remotely when a new firmware is available. The users are also allowed to monitor the image and take snapshots via the network.
automatically. This allows the camera to capture clear image whenever the environment light changed. PoE Supported PoE (Power over Ethernet) standard enables the camera to be powered by the Ethernet, which simplifies your surveillance system by eliminating the need of power outlet. The PoE camera features both stability and security, providing a cost-saving solution to your application of Internet camera. Please make sure that you remove the power adapter when the camera power is supplied through PoE.
1.4 System Requirement NOTE: Networking LAN 10 Base-T Ethernet or 100Base-TX Fast Ethernet; Auto-MDIX. PoE IEEE 802.3af PoE Accessing the Camera using Web Browser Platform Microsoft® Windows® 7/Vista/XP CPU Intel Pentium III 800MHz or above RAM 512MB Resolution 800x600 or above User Interface Microsoft® Internet Explorer® 6.
C HAPTER 2 HARDWARE INSTALLATION - 13 -
2.1 Assembling the Camera Mounting Bracket Assemble the sun visor and camera mounting bracket to the camera by using the provided screws and washers, and then the camera can be mounted on the wall (or ceiling) securely through the three screw holes on the base of the holder. Adjust the camera position Once you have mounted the camera to the wall (or ceiling), you need to adjust the camera position to focus on the location where you want to monitor.
junction points of the connectors while you connect the cables or purchase a weatherproof cable/power cord protector. 2.3 Installing the Memory Card The camera provides a SD card slot that allows you to install the memory card (not included in the package) to store files. To install the memory card: 1. Remove the back cover of the camera by unscrewing the three screws. 2. Locate the SD card slot inside the camera, and then insert the memory card into the slot. 3.
2.4 Applications of the Camera The camera can be applied in multiple applications, including: Monitor local and remote places and objects via Internet or Intranet. Capture still images and video clips remotely. Upload images or send email messages with the still images attached. The following diagram explains one of the typical applications for your camera and provides a basic example for installing the camera. NOTE The camera’s connectors are not waterproof.
C HAPTER 3 ACCESSING THE CAMERA 3.1 Using IP Setup The camera comes with a conveniently utility, IP Setup, which is included in the Installation CD-ROM, allowing you to search the camera on your network easily. 1. Insert the Installation CD-ROM into your computer’s CD-ROM drive to initiate the Auto-Run program.
2. Click the IP Setup from the Auto-Run menu screen. Then IP Setup Wizard will appear. Click “Next” when the Welcome to the IPSetup Setup Wizard appears. 3. Click “Browse” to choose the desired destination location. By default, the destination location is C:\Program Files\TRENDnet\IPSetup. Then Click “Next”.
4. Click “Next” to confirm the IPSetup software to be installed to the computer. 5. When the Installation Complete window appears, click “Finish”.
6. After installing the IPSetup utility, the application is automatically installed to your computer, and creates a folder in “Start \Program\TRENDnet\IPSetup”. 7. Click Start > Programs > TRENDnet > IPSetup, and then click IPSetup 8. The IPSetup window will appear. It will search the Camera within the same network.
- Camera Display Area: It shows the connected camera(s) within the same network. By default, the IP setting on the Camera is set up DHCP. If you have DHCP server, the camera will automatic get the IP address from DHCP server. If you do not have DHCP server on your network, it will show the default IP as 192.168.10.30. Double click the IP address; it will link to Camera’s Web Configuration page. - Change IP: Click this button to bring up the following window. It allows you to change the IP Address.
3.2 Accessing to the Camera By default, the IP setting on the camera is set to DHCP. It is recommend to use IPSetup to find the camera’s IP address. Once you find the IP address of the camera, click Link to access the camera’s web page. TIP If the camera cannot get the IP address from DHCP server, you can access the camera by manually entering the default IP address: 192.168.10.
The Main screen will appear as below: The Main screen of the Web Configuration provides you with the useful information and functions, including: Live View/Setup Switch: Click the details, see Chapter 4. button to configure the camera. For Click the button to return to the Main screen to view the live view image. Compression Buttons: Select to transmit and record the video using H.264, MPEG4 or MJPEG compression.
Snapshot allows you to capture and save a still image. Browse allows you to assign the destination folder to store the video clips and still images. Talk allows you to speak out through the camera. Please note only one user is allowed to use this function at a time. Listen allows you to receive the on-site sound and voice from the camera. Trigger Out allows you to trigger on/off the GPIO output manually. Multicast allows you to change the camera’s transmission type between multicast/unicast.
3.3 Configuring the IP Address of the Computer If you are failed to access to the camera, please check the IP address of your computer. When you connect the camera to your computer directly to proceed with configuration of the camera, you need to set up the IP addresses to be in the same segment for the two devices to communicate. 1. On your computer, click Start > Control Panel to open the Control Panel window. 2. Double-click Network Connection to open the Network Connection window. 3.
C HAPTER 4 CONFIGURING THE CAMERA 4.1 Using the Web Configuration You can access and manage the camera through the Web browser and the provided software application UltraView Pro. This chapter describes the Web Configuration, and guides you through the configuration of the camera by using the Web browser. To configure the camera, click on the Main screen of Web Configuration. The Web Configuration will start from the Basic page.
4.2 Using Smart Wizard The camera’s Smart Wizard lets you configure your camera easily and quickly. The wizard will guide you through the necessary settings with detailed instructions on each step. To start the wizard, click Smart Wizard in the left menu bar. Step 1. Camera Settings By default, the camera name is set as model number. Change the name if necessary. Enter the location and administrator password twice.
Step 2. IP Settings Setup the IP setting, DHCP, Static IP or PPPoE. Step 3. Email Settings Enter the mail server information. If you are using a free mails server, select the SSL and/or STARTTLS according to the mail server requirement.
Step 4. Confirm Settings Click Apply to finish the setting or click Prev to change the previous setting or click Cancel to disregard all setting.
4.3 Basic Setup The Basic menu contains three sub-menus that provide the system settings for the camera, such as the Camera Name, Location, Date & Time, and User management.
4.3.1 Basic >> System Basic: This item allows you to assign the camera name and location. Camera Name: Enter a descriptive name for the camera, which will help you to identify the camera when you have multiple cameras on your network. By default, the camera name is set as the model number. Location: Enter a name where the camera is located Indication LED: This item allows you to set the LED illumination as desired. The available options include: Normal and OFF.
4.3.2 Basic >> Date & Time Date and Time: Enter the correct date and time for the camera. TimeZone: Select the proper time zone from the pull-down menu. Synchronize with PC: Select this option and click Apply. The date & time settings of the camera will be synchronized with the connected computer. Synchronize with NTP Server: Select this option and enter the NTP Server IP address, then click Apply. The date/time will be synchronized from the NTP Server. By default, the update interval is set to 6 hours.
4.3.3 Basic >> User Administrator: To prevent unauthorized access to the camera’s Web Configuration, you are strongly recommend to change the default administrator password. Type the administrator password twice to set and confirm the password. General User User Name: Enter the user’s name you want to add to use the camera. Password: Enter the password for the new user. UserList: Display the existing users of the camera. To delete a user, select the one you want to delete and click Delete.
Guest User Name: Enter the guest’s name you want to add to use the camera. Password: Enter the password for the new guest. UserList: Display the existing guests of the camera. To delete a user, select the one you want to delete and click Delete. NOTE The “General User” can access the camera and control the Function buttons of the camera’s Web Configuration; the “Guest’ can only view the live view image from the Main screen of the Web Configuration while accessing the camera.
4.4 Network Settings The Network menu contains two sub-menus that provide the network settings for the camera, such as the IP Setting, DDNS Setting, and IP Filter. 4.4.1 Network >> Network IP Setting: This item allows you to select the IP address mode and set up the related configuration. The default setting is DHCP mode enabled. DHCP: Select this option when your network uses the DHCP server. When the camera starts up, it will be assigned an IP address from the DHCP server automatically.
Static IP: Select this option to assign the IP address for the camera directly. You can use IPFinder to obtain the related setting values. IP Enter the IP address of the camera. The default setting is 192.168.10.30. Subnet Mask Enter the Subnet Mask of the camera. The default setting is 255.255.255.0. Default Gateway Enter the Default Gateway of the camera. The default setting is 192.168.10.1. Primary/ Secondary DNS DNS (Domain Name System) translates domain names into IP addresses.
device interoperability. In addition, it supports port auto mapping function so that you can access the camera if it is behind an NAT router or firewall. Select the Enable option to enable this feature. Ports Number HTTP Port: The default HTTP port is 80. NOTE If the camera is behind an NAT router of firewall, the suggested port to be used is from 1024 to 65535. 4.4.
Bonjour: The devices with Bonjour will automatically broadcast their own services and listen for services being offered for the use of others. If your browser with Bonjour, you can find the camera on your local network without knowing its IP address. The Apple Safari is already with Bonjour. You can download the complete Bonjour for Internet Explorer browser from Apple's web site by visiting http://www.apple.com/bonjour/.
4.4.3 Network >> IP Filter The IP Filter setting allows the administrator of the camera to limit the users within a certain range of IP addresses to access the camera. To disable this feature, select the Disable option; otherwise, select the Accept option to assign the range of IP addresses that are allowed to access the camera, or select the Deny option to assign the range of IP addresses that are blocked to access the camera. Disable: Select this option to disable the IP Filter function of the camera.
located within 192.168.10.50 ~ 192.168.10.80 will not be allowed to access the camera. IPv6: Enter the IP Address that is allowed to access the camera. Deny IPv4: Assign a range of IP addresses that are blocked to access the camera by entering the Start IP address and End IP address options. When you are finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. For example, when you enter 192.168.10.50 in Start IP Address and 192.168.10.
4.5 Setting up Video & Audio The Video & Audio menu contains four sub-menus that provide the video and audio settings for the camera.
4.5.1 Video & Audio >> Camera Image Setting Black Level: Adjust the brightness level from 0 ~ 5. Brightness: Adjust the brightness level from 0 ~ 100. Saturation: Adjust the colors level from 0 ~ 100. Sharpness: Adjust the sharpness level from 0 ~ 100. TIP Click Default to restore the default settings of the three options above. Mirror: Select Vertical to mirror the image vertically, or select Horizontal to mirror the image horizontally.
4.5.2 Video & Audio >> Video H.264 Video Resolution: Select the desired video resolution from the four formats: SXGA, VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. Frame Rate: Select Auto or a proper setting depending on your network status.
Frame Rate: Select Auto or a proper setting depending on your network status. MJPEG Video Resolution: Select the desired video resolution from the four formats: SXGA, VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. Video Quality: Select the desired image quality from five levels: Lowest, Low, Medium, High, and Highest. Frame Rate: Select Auto or a proper setting depending on your network status. NOTE The camera supports H.
4.5.3 Video & Audio >> Audio Camera Microphone In: Select the Enable option to enable the camera’s audio function, so that you can receive the on-site sound and voice from the camera. Camera Speaker Out: Select the Enable option to enable the camera’s external speaker function, so that the connected speaker can play the sound and voice through the camera. You can set the speaker’s volume by entering the proper value in the Volume option. The default setting is 90.
4.5.4 Video & Audio >> Overlay / Mask This sub-menu is used to set the image overlay and mask feature of the camera. Image Overlay: This item allows you to set the image overlay. In the Image File option, click Browse to select the image file from your computer, and then click Upload. You can click Preview to check the image size and adjust the image position before clicking Upload. The preview image area is displayed with red dotted line.
NOTE The width and height of the input overlay graphic should be multiple of 4 at a maximum size of 43690 pixels, and in JPG or BMP (24-bit RGB) format. Privacy Mask: This item allows you to configure up to two mask areas. Select the area 1 or 2 from the Window pull-down list, and then click Enable. You can change the size and position of the area by holding and dragging the mouse. You can also change the color of the mask area by clicking the Color box and then selecting the color you want.
For example, when you select the Include Date & Time and Include Text options and click Apply, you can see the related information displayed on the live view image when you click the - 48 - button.
4.6 Event Server Configuration The Event Server menu contains four sub-menus that allow you to upload images to FTP, send emails that include still images, and store the images to a NAS system. When you complete the required settings for HTTP, FTP, Email, or Network Storage, click Test to test the related configuration is correct or not. Once the camera connects to the server successfully, click Apply.
4.6.1 Event Server Setting >> HTTP HTTP Notify For Motion Trigger Send the query parameter via an HTTP notification when an event is triggered.
Example: Host: 192.168.10.1 Port: 80 Query: xxx.cgi?name1=value1&name2=value2 Ex: cgi/event.cgi?status=#s&time=#t&model=modelname Result: http://192.168.10.1:80/cgi/event.cgi?status=#s&time=#t&model= modelname 4.6.2 Event Server Setting >> FTP FTP Host Address: Enter the IP address of the target FTP server. Port Number: Enter the port number used for the FTP server. User Name: Enter the user name to login into the FTP server. Password: Enter the password to login into the FTP server.
FTP Upload with: Select upload to FTP with one snapshot image or a series image in pre-event/post-event time when event triggered. NOTE Due to the network environment, the camera may not upload number of images that you set. 4.6.3 Event Server Setting >> Email Email SMTP Server Address: Enter the mail server address. For example, mymail.com. If you are using a free mail service (e.g. Google Gmail®, Yahoo®, Hotmail®), please enter the SMTP server address from the service provider.
SMTP Port: Assign the SMTP port in the text box. The default SMTP port is 25. If the mail server requires an encrypted connection, you should check the SSL option. SSL / STARTTLS: Most free email services require an encrypted connection. If you are using a free email service, please check the mail server requirement and select the options that apply to the server. Authentication Mode: Select None or SMTP according to the mail server configuration.
4.6.4 Event Server Setting >> Network Storage Network Storage Samba Server Address: Enter the IP address of the Network Storage server. Share: Assign the folder on the Network Storage server to share the files to users. Path: Assign the path for uploading the files on the Network Storage server. For example, Test. User Name: Enter the user name to login into the Network Storage server. Password: Enter the password to login into the Network Storage server.
Encode Format: Select MPEG4 or H.264 as the encode format while recording. File Format: Select MP4 or AVI as the file format while recording. NOTE The recorded video files in Network Storage are enclosed by AVI format without audio. 4.6.5 Event Server Setting >> Instant Message The camera supports the Jabber IM service, so that you can send an instant message once you have a Jabber account. For more information of Jabber, please visit the Jabber Website at: http://jabber.org/Main_Page.
Instant Message Jabber ID: Enter your user ID to login into the Jabber IM service. Jabber Password: Enter the password to login into the Jabber IM service. Manually Specify Server Host/Port: Select the Enable option to manually configure the Jabber server settings. Jabber Server Address: Enter the Jabber server address manually. Jabber Port: Assign the Jabber port manually in the text box. Encrypt Connection: Select the Enable option to secure the connection.
4.7 Motion Detect The Motion Detect menu contains the command and option that allow you to enable and set up the motion detection feature of the camera. The camera provides three detecting areas. To enable the detecting area, select Window 1/2/3 from the pull-down list, and then select Enable. When the detecting area is enabled, you can use the mouse to move the detecting area and change the area coverage. Name: Assign a name to the detecting area.
4.8 Event Configuration The Event Config menu contains five sub-menus that provide the commands to configure event profiles.
4.8.1 Event Configuration >> General Setting General Snapshot/Recording Subfolder: You can assign a descriptive name for the subfolder to save the captured image/video files. Otherwise, leave this option blank to use the default setting. Storage Recording Time Per Event: Limit the recording time while you are using the Network Storage solution. GPIO Trigger Out Retention Time Per Event: Limit the retention time of the GPIO Trigger Out function. 4.8.
Profiles list. To delete the profile, select the profile in the list and click Delete. Profile Name: Display the profile name that you select in the Schedule Profiles list. Weekdays: Select the weekday(s) that you want to separately assign in the schedule profile. The weekday that has been assigned will be displayed with green color. Time List: Display the time period that you have assigned within the selected weekday.
4.8.3 Event Configuration >> Motion Detect Trigger Motion Detect Trigger: Select the Enable option to enable the trigger function of the camera, so that you can send captured images within the detecting area to the FTP server, email receiver, or the Network Storage server. You have to configure corresponding settings, such as FTP server and email server, to enable this feature. Please note that you have to configure the related settings before enabling these features.
4.8.4 Event Configuration >> Schedule Trigger You can separately configure the schedule for trigger function of the camera by Email, FTP, or Network Storage. Select the Enable option on each item, and then select a Schedule Profile from the pull-down list and set the Interval time. NOTE If the setting value of the Network Storage Recording Time Per Event option in General Setting is longer than the Interval time in Network Storage Schedule, the recorded file will be a continuous video clip.
4.8.5 Event Configuration >> GPIO Trigger GPIO Trigger: Select the Enable Trigger In 1/2 option to enable the GPIO trigger function of the camera, so that you can set Trigger Out function or send captured images within the detecting area to the SD card, FTP server, email receiver, Network Storage server, or send an instant message. Event server has to be configured prior to using the functions. Schedule Profile: Select a schedule profile from the pull-down list.
4.9 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera.
Factory Reset: Click Reset to restore all factory default settings for the camera. You can also do the physical reset by press the reset button on the camera. Remove the front cover of the camera and press the reset button as indicates below. System Reboot: Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. Configuration: You can save your camera configuration as a backup file on your computer.
4.10 RS-485 The RS-485 menu provides the control settings for external device through the I/O port.
4.10.1 RS-485 >> RS-485 Setting Select the Enable option and complete the required configuration to use the RS-485 function of the device. Popular Protocol Setting: Select a Protocol (Pelco-D or Pelco-P) and then select a Camera ID. Custom Protocol Setting: Select this option to configure the commands protocol manually. You can click Test to test each command that you have assigned. In the Name and Command string boxes, you can customize more buttons for your needs.
4.10.2 RS-485 >> Patrol The Patrol function provides the patrol control settings for the connected camera. Preset Position To set the preset position for the connected camera: 1. Use the Navigation buttons to move the camera lens to the desired position. 2. Select a Position number (Home, 2~32) from the Preset Position pull-down list. 3. Enter the descriptive name for the location in the text box. 4. Click Apply. Pan Speed: Adjust the moving speed (1 ~ 10) while panning the lens.
Zoom Speed: Adjust the speed (1 ~ 10) while zooming the lens. Focus Speed: Adjust the speed (1 ~ 10) while focusing the lens. Zoom In/Zoom Out: Click to zoom in/out the live view image. Focus Far/Focus Near: Click to adjust the focus by far/near. Patrol Position This field allows you to set the positions for camera’s patrolling: 1. Select a preset position from the Preset Position pull-down list, and then click Add to be Patrol Position. The preset position will be added to the Patrol Path list. 2.
4.11 Setting up the SD Card The SD Card menu allows you to set the SD card function installed in the camera.
4.11.1 SD Card >> SD Card Setting SD Card Dismount: Click Dismount to safely remove the SD card that is installed in the camera. Note: You must disable the event trigger in order to dismount the SD Card. SD Card Information: Displays the information of the installed SD card, including the Total space and Free space. SD Card Setting When Storage Full: Select Stop Recording or Recycle – Delete Oldest Folder when the storage space on the SD card is full. Encode Format: Select MPEG4 or H.
4.12 Information The Information menu displays the current configuration and events log of the camera.
4.12.1 System Information >> Device Information Display the Basic, Video & Audio, and Network settings of the camera. 4.12.2 System Information >> Logs The Logs table displays the events log recorded by the system.
C HAPTER 5 S ECUR V IEW ™ P RO S OFTWARE This chapter describes detailed instructions on using SecurView™ Pro, a customized software application with a user-friendly interface that allows you to access your cameras. The Software can monitor and record up to 36 cameras. It also let you change some basic settings of the camera, such as schedule profiles and motion detecting areas. The SecurView™ Pro also supports audio or Pan/Tilt function.
5.1 Installation 1. Insert the Installation CD-ROM into your computer’s CD-ROM drive to initiate the Auto-Run program. 2. Click the SecurView™ Pro from the Auto-Run menu screen. NOTE: To use SecurView™ Pro, you must have Microsoft .NET Framework 2.0 installed in the computer. The setup wizard will detect it and, if the program is not installed yet, it will ask you to install it during the process of installing SecurView™ Pro. NOTE: Microsoft® Windows® Installer 3.
3. Then SecurView™ Pro Setup Wizard will appear. Click “Install”. 4. Wait until the program finish the installation. By default, the destination location is C:\Program Files\TRENDnet\SecurView Pro.
5. Click “Finish” to finish the installation. 6. After installing the SecurView™ Pro, the application is automatically installed to your computer, and creates a folder in “ Start \Program\TRENDnet\SecurView Pro ”.
5.2 Using SecurView™ Pro 5.2.1 Launch the Program To start SecurView™ Pro, click Start > All Programs > TRENDnet >SecurView™ Pro > SecurView™ Pro. You can also start the program by double-click the SecurView™ Pro icon on your desktop. On the login window, enter the User name/Password and click OK to login. The default User name/Password is admin/admin. If you wish to save the login information, please select Auto Login.
5.2.2 Main Window and Features When you start and login to SecurView™ Pro, the Main window will display as below: The Main window provides you with the information on operating the system, as well as the control panel such as the Quick Launch buttons, and so on. NOTE For best result, it is higher recommended to configure resolution setting to 1024 x 768 or higher; otherwise, it cannot be displayed on the screen when launching the program.
Quick Launch Buttons are located below the Live View Window, providing you with the following quick-launch functions: Button Function Logout : To log out the SecurView™ Pro program Close: To close the SecurView™ Pro program Restore Recording Type: Restore all recording type to current camera’s setting All Continuous Recording: Continuous recording on all cameras Stop All Recording: Stop recording on all cameras View Setting: To configure eMap settings eMap View: To view current maps Camera Status: Displa
Camera View Mode buttons in this area allow you to switch the camera view mode. Buttons Functions Display the connected camera(s) in a single camera view mode. Display the connected camera(s) in a quad view mode. Display the connected camera(s) in a 3 x 3 grid view mode. Display the connected camera(s) in a 13-camera view mode using a split window. The first camera is displayed as the major view. Display the connected camera(s) in a 17-camera view mode using a split window.
Camera List displays the status of the connected cameras. If multiple cameras are connected, you can switch to the live view of each camera by simply selecting the camera from the list. eMap allows you to select the desired camera to the view from the map easily. Please note that you have to set up the eMap for monitoring in advance. Camera Control Buttons provides the control buttons that allow you to control the selected camera. Buttons Functions Talk On/Off.
5.2.3 Manage the Cameras Before adding the cameras, please setup the recording setting first. Configure Recording Settings 1. Click the button and then select Record Setting. 2. Default path is C:\, click Browse and select the desire directory then click Save to complete the configuration. To change the time interval for recording, select time from the pull-down menu. NOTE: The system will automatically delete the oldest files (10%) when the size of recorded files is up to 90% of the storage space.
Add a Camera 1. Click the button and select Device Setting to display the Device Setting window. 2. Click New.
3. Click on Search, all cameras that’s connected to your network would appear. 4. Select the camera you would like to add and then click Add.
5. The information of the camera will display on the screen. It will auto detect the IP address/port number and display the stream type of the camera. Please type in the correct user name and password, then select Preview to view live image. 6. To setup recording style, select Yes on Record option. These four recording types will appear. Select one of the recording type, configure it then click Save.
Records stream video by schedule. You can setup the schedule by click Add Schedule here. Click on New to create a new schedule and select the time to record. Click on Save when finish. Motion: Record video by Motion Detection. Motion detection recording required to setup a motion detection area. If you are adding a new camera, you must preview the camera first in order to setup the motion detection area.
Click on Motion detection area to setup Enable motion detection windows, set up the senstivity and click on Save.
Motion by Schedule: same requirement as Motion & Schedule recording. Digital Input: Recording triggered when there I/O port is triggered. After all recording methods are configured, click Save to apply the settings.
7. Camera list will appear with recording type notification. 8. Once you added all the cameras, click the close button “x” on the Device Setting windows to return to the main windows. The cameras will display here.
NOTE Divx/Xvid codec is required for viewing the image of camera. If the image cannot be displayed in the Live View/Preview window normally, click the following path to download and install the required component: http://download.divx.com/divx/DivXInstaller.exe Edit / Delete a Camera 1. To edit a camera: From the Device Setting window, highlight the camera you would like to edit then click on Modify button.
2. To delete a camera: select the desired one and then click Remove. Click Yes to confirm. View Camera Image Since you have added camera(s) to the system, the image of the selected camera(s) will be displayed on the Live View Window automatically. You can view a maximum of 36 cameras simultaneously. Additionally, you can select one-camera or other view mode to display the video from the Camera View Mode buttons.
The Information icon ( ) on the top-right corner of the window provides you with the options to connect/disconnect the camera, select a camera to be displayed in the window, capture a still image of the camera live video, or switch to eMap mode. Click the Information icon to pop up the shortcut menu and select the desired option.
Playback the Recorded Files 1. Click the button to display the Playback window. 2. On the Playback window, select the camera and setup the begin/end date and begin/end time, then click Search. The search result will be displayed in the Record File list.
3. To playback the video clip, select the desired file and click Play. 5.2.4 eMap Setup & Camera Status Manage eMap Click the button and select View Setting to manage eMap. eMap refers to the geography and device scope in the SecurView™ Pro, which visually presents the devices in your security system. It uses a background of the area (e.g. a picture or a map) as the interface for monitoring.
To add an eMap 1. On the View Setting window, click New. 2. Enter an eMap name.
3. Click Browse to select a Picture File from your computer. Picture will display in the Preview window. 4. Click Save and click OK to apply the settings.
5. Click Camera Location to assign the camera location. 6. The following screen appears.
7. Select the camera from the list and then click the position on the map. The camera icon 8. Click Save when complete. - 99 - will be displayed on map.
To modify/remove an eMap 1. To edit the eMap: In the eMap List, select the map name from eMap list, and click Modify. 2. The map’s information will display on the preview windows. After changes the setting information, click Save to save the setting.
3. To delete the eMap: In the eMap List, select the desired one and click Remove. The selected map will be removed from the list.
View eMap a. b. Click the button and select eMap View. Select the map from the eMap Name list.
Camera Status Click the camera icon , the camera Live Monitor window will display live image on that camera. 5.2.5 System Info Account Click the System button and select Account to change the administrator password of the system.
Enter the Current password, and then enter the new password twice (in the Type new password and Retype password boxes). Then click Save. Version Click the System button and select Version to view the current firmware version of the system.
System Setting Click the System button and select System Setting. Auto Scan period can be set from 30 seconds to 100 seconds. 5.2.6 Event Settings Setting up Event Server Click the button and select Event Server to configure the SMTP settings for email notification use.
Select the Enable SMTP option and configure the following information correctly to start the email feature. SMTP Server Address: Enter the mail server address. For example, mymail.com or smtp.gmail.com or smtp.live.com Sender Email Address: Enter the email address of the user who will send the email. For example, John@mailserver.com. Authentication Mode: Select None or SMTP according to the mail server configuration. Sender User Name: Enter the user name to login the mail server.
Port Number: Enter the port number used for the email server. SSL: If the mail server requires an encrypted connection, you should check the SSL option. For example, gmail users, please select this option. When completed, click Save and then select OK. The system will automatically start the Event Service. TIP The status of Event Service is indicated by the bar.
Sending Notification to the User Click the button and select Address Book to assign the user to the Address Book of the camera. The user will receive a realtime notification from the system while triggering out. 1. On the Address Book window, click New. 2. In the Address Book Information field, enter the Name and Email of the user. 3. When completed, click Save. The user will be displayed in the Address Book List. 4.
be displayed, where you can change the user’s information and then click Save when completed. 5. To delete the user: In the Address Book List, select the desired user and click Remove. The selected user will be removed from the list. Configuring Event Trigger Click the button and select Event Trigger to configure the trigger out function of the camera. 1. On the Event Trigger window, select the desired camera from the Camera List.
2. Do one of the following: SMTP: Select this option and enter the Subject and Message, the system will send an email message to the selected user(s) in the Address Book List. Play Sound: Select this option select a sound file from the computer, so that the system will alarm by the sound while triggering out. eMap Popup: Select this option and select the eMap profile from the pull-down menu. The camera view of the eMap will be displayed while triggering out. 5.2.
C HAPTER 6 How to access the camera behind a Router You can either setup the Dynamic DNS connection via camera itself or your home router. An account from any of the listed DDNS providers is required prior to this operation. Configure DDNS on your Camera 1. Go to Camera’s DDNS Setting page, click Enable to activate the feature. Then select a DDNS provider from the list. 2. Enter your DDNS’s the Host Name, User Name and Password.
3. In the Port Number section, assign an HTTP port of the camera. The default HTTP Port on the camera is 80. The example shows above is using port number 9000. 4. Open another web browser and go to your Router’s Web Configuration page. (In the example, TRENDnet’s TEW-651BR Wireless N router is used) 5. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg.
Private Port: The HTTP port that you assign on your Camera. Public Port: The port used on remote side to access to your Camera. LAN Server: The local IP address of your Camera. Then click Add to add the application. * Please refer to your router’s user’s manual for detail Virtual Server setting. Some router might use Port Forwarding or Special applications for this function. The setup steps should be very similar.
6. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber 7. Camera’s login page will appear. Configure DDNS on your router 1. Go to Camera’s DDNS Ports Number section, assign a HTTP port for your camera and click Apply. 2. Login to your router’s web configuration page.
3. Find the Dynamic DNS configuration section. 4. Enable DDNS, fill out the following information and then click Apply.
5. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg. Camera Name) Protocol: Select TCP Private Port: The HTTP port that you assign on your Camera. Public Port: The port used on remote side to access to your Camera. LAN Server: The local IP address of your Camera. Click Add to add the application. * Please refer to your router’s user’s manual for detail Virtual Server setting.
Appendix A.1 Specification Image Sensor Sensor Resolution Min. Illumination 1/3” 2-megapixel color CMOS Sensor 1600 x 1200 0 Lux System Hardware Processor RAM ROM Power ARM9 base 64MB SDRAM 8MB NOR Flash DC12V / AC24V Lens Assembly Lens Type Lens Specification View Angle Night Vision Video Compression Video Resolution Board lens F1.8, 12mm 28.5 degree 850nm IR LED (Auto mode and Schedule mode supported); up to 20M H.
Audio Input Output Format 3.5mm external microphone input jack 3.5mm speaker output jack (Mono) PCM/AMR (AMR is for 3GPP only) User Interface LAN SD Card Slot I/O Connectors RJ-45 port Yes GPIO: 2-in/1-out connectors; RS-485; AC24V Communication LAN PoE Protocol Support Software OS Support Browser Software 10/100Mbps Fast Ethernet, auto-sensed, Auto-MDIX IEEE802.
A.2 GPIO Terminal Application Typically used in association with programming scripts for developing applications for motion detection, event triggering, alarm notification via e-mail, and a variety of external control functions. The 8-pin I/O Terminal Block is located on the rear panel and provides the interface to: a photocoupled switch output, a photo-coupled input, and RS-485 interface. The RS-485 is typically used for pan/tilt control.
A.3 Bandwidth Reference Guide H.
A.4 Glossary of Terms NUMBERS 10BASE-T 10BASE-T is Ethernet over UTP Category III, IV, or V unshielded twisted-pair media. 100BASE-TX The two-pair twisted-media implementation of 100BASE-T is called 100BASE-TX. A ADPCM Adaptive Differential Pulse Code Modulation, a new technology improved from PCM, which encodes analog sounds to digital form. AMR AMR (Adaptive Multi-Rate) is an audio data compression scheme optimized for speech coding, which is adopted as the standard speech codec by 3GPP.
Communication Communication has four components: sender, receiver, message, and medium. In networks, devices and application tasks and processes communicate messages to each other over media. They represent the sender and receivers. The data they send is the message. The cabling or transmission method they use is the medium. Connection In networking, two devices establish a connection to communicate with each other.
distributed company and operates the company’s missioncritical applications. Ethernet The most popular LAN communication technology. There are a variety of types of Ethernet, including 10Mbps (traditional Ethernet), 100Mbps (Fast Ethernet), and 1,000Mbps (Gigabit Ethernet). Most Ethernet networks use Category 5 cabling to carry information, in the form of electrical signals, between devices. Ethernet is an implementation of CSMA/CD that operates in a bus or star topology.
is easier for humans to read hexadecimal numbers than binary numbers. I Intranet This is a private network, inside an organization or company that uses the same software you will find on the public Internet. The only difference is that an Intranet is used for internal usage only. Internet The Internet is a globally linked system of computers that are logically connected based on the Internet Protocol (IP). The Internet provides different ways to access private and public information worldwide.
J JAVA Java is a programming language that is specially designed for writing programs that can be safely downloaded to your computer through the Internet without the fear of viruses. It is an object-oriented multi-thread programming best for creating applets and applications for the Internet, Intranet and other complex, distributed network. L LAN Local Area Network a computer network that spans a relatively small area sharing common resources.
network are: LAN – (local area network): Computers are in close distance to one another. They are usually in the same office space, room, or building. WAN – (wide area network): The computers are in different geographic locations and are connected by telephone lines or radio waves. NWay Protocol A network protocol that can automatically negotiate the highest possible transmission speed between two devices.
Protocols that dictate the format of data for transferors the medium include token-passing and Carrier Sense Multiple Access with Collision Detection (CSMA/CD), implemented as token-ring, ARCNET, FDDI, or Ethernet. The Router Information Protocol (RIP),a part of the Transmission Control Protocol/Internet Protocol (TCP/IP) suite, forwards packets from one network to another using the same network protocol. R RJ-45 RJ-45 connector is used for Ethernet cable connections.
Workstations, single-attach stations, dual-attach stations, and concentrators are FDDI stations. Subnet mask In TCP/IP, the bits used to create the subnet are called the subnet mask. T (TCP/IP) Transmission Control Protocol/Internet Protocol is a widely used transport protocol that connects diverse computers of various transmission methods. It was developed y the Department of Defense to connect different computer types and led to the development of the Internet.
WEP WEP is widely used as the basic security protocol in Wi-Fi networks, which secures data transmissions using 64-bit or 128-bit encryption. Windows Windows is a graphical user interface for workstations that use DOS. WPA WPA (Wi-Fi Protected Access) is used to improve the security of Wi-Fi networks, replacing the current WEP standard. It uses its own encryption, Temporal Key Integrity Protocol (TKIP), to secure data during transmission.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TV-IP322P – 3 Years Limited Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.
Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees.
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California.
- 133 -
