TV-IP400 TV-IP400W Quick Installation Guide Version 09.08.05 TRENDnet TRENDware, USA What's Next in Networking Copyright ©2005. All Rights Reserved. TRENDware International, Inc.
Table of Contents English ...................................................................................................... 1. Prepare for Installation ...................................................................... 2. Install Hardware ................................................................................ 3. Configure the Internet Camera .......................................................... 4. Using the Internet Camera Wirelessly (TV-IP400W only) .................
English QIG 1. Prepare for Installation Thank you for purchasing the TV-IP400/TV-IP400W. This Internet Camera will allow you to view live images from internal and external networks. This guide will help you set up and configure your Internet Camera. Following the installation instructions should be quick and easy. If you run into problems, please refer to the Troubleshooting section or the more detailed installation procedures on the CD User's Guide. If you need further technical support, please visit www.
2. Install Hardware 1. Place the camera on a flat, level surface. 2. Connect the RJ-45 network cable to the Internet Camera then connect the other end of the network cable to a switch or hub. 3. Connect the power adapter to the Internet Camera. Make sure use the power adapter supplied with the Internet Camera. Note: Using a different power adapter may damage the unit.
3. Configure the Internet Camera 1. Open Internet Browser Window and enter (camera's default IP address) Note: The PC's IP (Example 192.168.0.50) address must correspond with the Internet Camera's IP address (Default IP: 192.168.0.20) in the same segment for the two devices to communicate. 2. Click on System Administration to access the configuration page.
3. Click Configuration and click Network. Enter an IP address, Subnet mask, and Default gateway that corresponds with your existing network. Then click the Save button to keep the changes Note: If you need to access the configuration remotely, it is recommended to enter a static IP address and the Internet DNS IP address.
4. Using the Internet Camera Wirelessly (TV-IP400W only) 1. Click Configuration and click Wireless. 2. From the pull-down menu, select the SSID that matches your wireless access point and set Connection Mode to Infrastructure.
3. Scroll down to the bottom of the page and Click Save. 4. Disconnect the CAT5 cable and the power adapter connector from the TV-IP400W. 5. Reconnect the power adapter connector to the TV-IP400W. Allow 5-10 seconds for the TV-IP400W and the wireless Access Point to communicate wirelessly. Then type the IP Address that you assigned to the TV-IP400W in your web browser for verification.
Troubleshooting Q1. The image is blurry, how do I fix this? A1. You can adjust the Internet Camera's focus by rotating the lens. Q2. How do I view the Internet Camera's live images within my Local Network? A2. Open a web browser (Internet Explorer or Netscape), type your Wireless Internet Camera's IP address (i.e.: 192.168.0.20) in the Address bar, and then hit the Enter key. The Welcome page of the Internet Camera will appear. Q3. When I enter the IP address of the camera, the image does not load, why? A3.
2. Click on Custom Level and make sure all ActiveX controls are set to "Enable" and click OK. 3. Once you save the settings, the browser will load again and the image should appear.
Q5. How do I configure my computer's IP address? A5. For Windows 2000/XP users: - On the Desktop, right click on My Network Places g select Properties g right click on the Local Area Connection g select Properties, the Local Area Connection Properties Window will appear - Under General tab, select Internet Protocol (TCP/IP) g click on Properties button, Internet Protocol (TCP/IP) Properties Window will appear 1.
For Windows 98/ME users: - On the Desktop, right click on Network Neighborhood g select Propertiesg right click on the Local Area Connection g select Properties, the Local Area Connection Properties Window will appear - Under Configuration tab, select your Network Adapter (TCP/IP protocol) g click on Properties button, TCP/IP Protocol Properties Window will appear 1. Select Specify an IP address option and enter the IP, Subnet Mask addresses.
TRENDnet TRENDware, USA What's Next in Networking @ Product Warranty Registration Please take a moment to register your product online. Go to TRENDware’s website at http://www.TRENDNET.com TRENDnet Technical Support US/Canada Support Center Contact Telephone: 1(310) 626-6252 1(310) 626-6267 Fax: Email: support@trendnet.