Quick Installation Guide TV-IP410 TV-IP410W H/W: A1.
Table of Contents Table of Contents English ...................................................................................................... 1. Before You Start ................................................................................. 2. Hardware Installation ......................................................................... 3. Configure the Internet Camera .......................................................... 1 1 3 4 Troubleshooting ..............................................
1. Before You Start Package Contents TV-IP410 / TV-IP410W ? ? Utility CD-ROM ? Multi-Language Quick Installation Guide ? 1 x 2dBi Detachable Antenna (TV-IP410W) ? GPIO Adapter RJ-45 Cable ? ? Mounting Kit ? Power Adapter (12VDC, 1.
Application Home Monitoring Family Monitoring (TV-IP410) (TV-IP410) Wireless N Gigabit Router (TEW-633GR) Internet Cable/DSL Modem Property Monitoring (TV-IP410W) Wireless 54Mbps Business Monitoring (TV-IP410W) 100Mbps Home Monitoring Family Monitoring (TV-IP410W) (TV-IP410W) Wireless N Gigabit Router (TEW-633GR) Internet Cable/DSL Modem Property Monitoring (TV-IP410) Wireless 54Mbps 100Mbps 2 English Business Monitoring (TV-IP410)
2. Hardware Installation 1. Attach the Antenna. (TV-IP410W) 2. Connect a RJ-45 network cable from a Switch/Router to the Ethernet port of the Internet Camera Server. 3. Connect the AC Power Adapter to the Internet Camera Server and then to a power outlet. 4. Verify the Power and Link LEDs are on.
3. Configure the Internet Camera Note: 1. It is recommended that you configure the Internet Camera from a wired computer. 2. If you would like to use SecurView software, please refer to the User's Guide on the CD for more information. 1. Insert the Utility CD-ROM into your CD-ROM drive and then click IP Setup. 2. Follow the IPSetup Setup Wizard instructions and then click Next. 3. Click Close. 4. Go to Start -> Programs -> TRENDnet -> IPSetup and click IPSetup.
Note: By default, the IP setting on the TV-IP410/TV-IP410W is set to DHCP. Please skip to step 9. If you want to give the TV-IP410/TV-IP410W static IP address, continue on to step 5. 5. Select the camera server and click Change IP. 6. Configure the IP address to be in the same subnet as your network, type in the Administrator ID and Password and click Change. By default: ID: admin Password: admin 7. Click OK and wait 30 seconds. 8. Click OK.
9. Double click the camera server to access the browser configuration. 10. Enter the User name and Password, and then click OK. By default: User Name: admin Password: admin 11. Right click and select Install ActiveX Control. 12. Click Install. Note: If you have the TV-IP410W, continue on to step 13. If you have the TV-IP410, skip to step 16.
13. Click Setup, Network and then click Wireless. (TV-IP410W only). 14. Click Site Survey. Select your wireless network. If encryption is enabled, select the proper Authentication type, enter the Pre-Shared Key and then click apply. (Example shows WPA2-PSK. If your wireless network does not support WPA, select open or shared instead. Contact your network administrator for more information) (TV-IP410W only). 15. Disconnect the RJ-45 cable and unplug the power. Then plug the power back in (TV-IP410W).
16. Verify the Power and Link LEDs are on. 17. Click Live View. Your installation is now complete. Note: For detailed information regarding the TV-IP410/TV-IP410W configuration and advanced settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or TRENDnet's website at http://www.trendnet.com. Register Your Product To ensure the highest level of customer service and support, please take a moment to register your product Online at: www.trendnet.
Troubleshooting Q1: IP Setup is unable to detect my camera. What should I do? A1: First, verify that you have followed all the steps in the Section 2: Hardware Installation. Second, disable any software firewall programs such as ZoneAlarm or Norton Internet Security. If you are using Windows XP or Windows Vista, disable the built in firewall. Third, click on Search in the IPSetup setup wizard. Q2: I do not have a DHCP server or DHCP is disabled on my network and I am unable to configure the TV-IP410/W.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 USA Copyright ©2008. All Rights Reserved. TRENDnet.
