Table of Contents Chapter 1 Introduction 1 Features......................................................................................................................... 1 Safety Instructions ........................................................................................................ 2 Package Contents.......................................................................................................... 3 Hardware Details ..................................................................
Unix Troubleshooting................................................................................................. 56 Appendix A Specifications 57 General Specifications ................................................................................................ 57 Appendix B Windows Server Configuration 59 Windows NT 4.0 Server ............................................................................................. 59 Windows 2000/2003 Server ................................................
Chapter 1 Introduction This chapter provides an overview of your Print Server's features. Features Congratulations on the purchase of your new Print Server. Your Print Server was designed to provide a simple and efficient network printing solution. It is packed with features, including: Versatility. The Print Server supports up to four protocols: TCP/IP, SMB (Service Message Block), AppleTalk (EtherTalk), and NetBEUI.
Safety Instructions For your own safety, and to protect your Print Server, please observe the following safety advice. 1. Unplug this device from its power source before cleaning. Use only a slightly dampened cloth for cleaning. Do not use liquid or aerosol cleaners. 2. Avoid using this product near water. Exposure to water poses an electric-shock hazard. 3. Do not place the Print Server on an unstable surface. The device may fall causing serious damage to the device. 4.
Package Contents You should find the following items packaged with your Print Server. If any items are missing, contact your dealer immediately. • The Print Server unit • Power Adapter • One CD-ROM containing all support programs and this manual • Quick Install Guide Hardware Details Details of the LEDs and connections are in this Chapter. Further details are contained in Appendix A - Specifications.
TE100-P1P Print Server • Direct Attach • 1 Parallel Port • 10/100BaseT Figure 2: TE100-P1P Print Server Page 4
LED Indicators The TE100-P1U has two LED indicators on the top; the TE100-P1P's LEDs are on the end. The Error LED is red. The Status indicator LED is green. The LED indicator modes are described in the following table. Status LED (Green) Error LED (Red) Status Description Off Off No power. On Off Normal operation - Idle. Flashing Off Normal operation - transmitting or receiving packets from the network. On On Hardware error. On Flashing (USB only) No printer connected to the USB port.
Chapter 2 LAN Installation This chapter describes how to install the Print Server in your Local Area Network. Procedure 1. Preparation • Ensure the power is OFF. Do not connect the Print Server while power is On. • Find the Default Server Name for your Print Server. The Default Server Name is shown on a sticker on the base of the device. It consists of 8 letters and/or digits. Record this name; it may be needed during configuration. 2.
Chapter 3 Print Server Configuration This chapter provides an overview of the configuration process. Overview The Print Server is designed to support many different platforms, and the configuration required would depend upon the environment in which it is installed. • The Print Server usually requires configuration, but if there's a DHCP server on your network, then the device is just plug-and-play. A Windows-based setup Wizard is also provided on the CD-ROM to simplify this task.
Figure 3: Print Server Screen 3. Click Next on the first screen of the Wizard, to view a list of Print Servers on your LAN. 4. Select your new Print Server, then click Next to continue. 5. Enter the required data on the following screen. 6. 7. • Name of the Print Server can be changed if you wish. • Comment is optional. • Select or enter the Workgroup name for this Print Server.
Chapter 4 Client PC Configuration The chapter details the client configuration required on LAN clients to use the printer or printers attached to the Print Server. Overview Before performing client configuration, the Print Server must be installed on your LAN, and configured as described in Chapter 3. Both the Print Server and the attached printer must be powered ON.
Checking your Network Protocols (Windows 9x) Your PC must have EITHER the TCP/IP or NetBEUI protocols installed. (All versions of Windows after Windows 95 have TCP/IP installed by default.) • If using the Peer-to-peer Printing, the installation program will check this for you. • If using other methods, you must check manually, as follows: 1. Select the Settings - Control Panel - Network option on the Start Menu. You should see a screen like the one following: Figure 4: Network Configuration 2. 3.
Windows Peer to Peer Printing With this printing method, print jobs are stored (queued) on your PC, and then sent to the Print Server when it is available. Figure 5: Peer-to-Peer Printing Windows 2000 & XP require no additional software. For other versions of Windows, the supplied PTP (Peer-to-Peer) Printer Port software must be installed on each PC. Windows 2000/XP Setup The recommended printing method is to use LPR, as follows: 1.
3. Choose Standard TCP/IP Port, then click New Port. Figure 7: Add Port Screen 4. On the Add Standard TCP/IP Printer Port screen above, enter the IP Address of the Print Server in the Printer Name or IP Address field, then click Next. Figure 8: Additional Port Information Screen 5. On this screen, select Custom, and click the Settings button to view the screen below.
Figure 9: Port Settings Screen 6. On the Port Settings screen, shown above: 7. • Select LPR in the Protocol section • Enter a Queue name (L1 for Port 1, L2 for Port 2 if the Print Server has 2 printer ports) • Ensure the LPR Byte Counting Enabled setting is Enabled. • Click OK to confirm your changes and close this screen. Follow the prompts to complete the Wizard.
Windows 9x/ME Setup Before performing the following procedure, the Print Server must be installed on your LAN, and configured as described in Chapter 3. Both the Print Server and the attached printer should be powered ON. 1. Insert the supplied CD-ROM into your drive. If the setup program does not start, run SETUP.exe in the root folder. 2. Click the Installation button, then select the User Install. Figure 10: Installation Screen 3.
Figure 11: Print Port Setup (Peer-to-peer Printing) If your Print Server is not listed: 2. • Click the "Refresh" button. • Check that both the Print Server and the printer are properly connected, and powered on. • Check that the Print Server has been configured. (Use the Setup Wizard on the CD-ROM.) • If using TCP/IP, try installing the NetBEUI protocol. Then try again. Select the desired port on a Print Server, then click Next.
3. The printer port will be created, then a screen like the following will be displayed. Figure 12: Configure Printer Port 4. Select the correct Windows printer in the Existing Printers list, and click the Connect button. If the correct printer type is not listed, click "Add New Printer" to run the Windows Add Printer wizard. Step through the Wizard and install the required printer: 5. • Select the correct Printer Manufacturer and Model, or use the "Have Disk" option if appropriate.
• • Locate the Delete Port button. This button is on the Details or Ports tab, depending on your version or Windows. If the Print Server's IP Address is changed, and you can no longer print, delete the port (see procedure above) and re-install it. Advanced Port Options The options for the Peer-to-peer Printing are accessed via the Port Settings button. Use Start - Settings - Printers to open the Printers folder, then right-click the Printer, and select Properties.
Windows SMB Printing This method requires no additional software to be installed, but the NetBEUI or TCP/IP protocol must be installed on your PC. Use the following procedure to install the Print Server's printer as a Windows SMB network printer: 1. Double-click the Network Neighborhood icon on the desktop. 2. On the View menu, select Details. 3. Locate the desired Print Server, as shown below: • If it is the same Workgroup as your PC, it will be listed on screen.
Printing from MS-DOS Programs Windows can redirect print data from a parallel port on your PC (e.g. LPT1) to a network printer. This redirection is called "Capture Printer Port", and is useful for MS-DOS programs. The MS-DOS program is configured to use LPT1 (parallel port 1 on the PC), but Windows "captures" the print data and sends it to the network printer. Capture Settings - Windows 98/ME 1. Select Start - Settings - Printers to open the Printers folder. 2.
Capture Settings - Windows 2000/XP 1. Login as Administrator. 2. Open the command prompt window. 3. Enter the following command to capture data from LPT1 (parallel port 1) net use lpt1 \\server_name\printer_name /persistent:yes Where \\server_name\ printer_name is replaced with the actual path to your printer. e.g. net use lpt1 \\SC3000014\P1 /persistent:yes 4. Close the command prompt window.
Figure 19: Network Path - Windows XP 4. Browse the network, and locate the Server and Printer (or Print Queue) which your Network Administrator advised you to use. 5. Click OK, then Next. 6. Select the correct printer Manufacturer and Model, as advised by your Network Administrator, and click Next. 7. Follow the prompts to complete the Wizard. The new printer will be listed with any other installed printers, and may be selected when printing from any Windows application.
8. Click Select. Configuration is now complete. Printing Printing with the Print Server installed in an AppleTalk network is identical to normal printing. Just select File - Print and choose the desired printer. Advanced Setup and Management In a mixed Windows PC/Macintosh environment, you can use BiAdmin to configure the Print Server. See Chapter 5 for details on installing and using BiAdmin.
Figure 21: LPR Screen 4. Enter the IP address of the Print Server in the LPR Printer's Address field, and enter the Queue Name (e.g. L1). 5. Select the Printer Model from the drop-down list. 6. Click Add. Configuration is now complete.
Chapter 5 BiAdmin Management Utility This chapter describes the installation and operation of the BiAdmin Configuration & Management program. Requirements This program requires: • Windows 95, Windows 98 or ME • Windows NT 4.0, Windows 2000 or XP Additional Recommendations: • Screen resolution of 800 * 600 or greater. Installation Use the supplied CD-ROM. This CD-ROM will usually auto-run. If auto-run is disabled on your PC, run the SETUP.exe program in the root folder.
Device List The left panel displays a list of all Print Servers found on the network. When a Print Server is selected from the list, its details are displayed in the right panel. Note: If the IP address is "Null", please click the Refresh icon to get the value again. If the desired Print Server is not listed, try the following: • Check that the device is installed and ON, then Refresh the list.
Select the desired port from the drop-down list to display the current status of the printer attached to the port. Possible states are: • Status - On-line, Off-line, or Out of Paper • Printing Information - Idle, Printing If the printer is Bi-directional, and is not busy, the Configuration button will be available, allowing you to change the configuration of the attached printer. This button will be grayed out if the printer does not support this option, or if the printer is busy printing.
Menus Main Menu Device Status Same as Device Icon. Printer Status Same as Printer Status Icon. Configure Same as Configure Icon. Upgrade Same as Upgrade Icon. Refresh Same as Refresh Icon. Exit Same as Exit Icon. InitDevice Menu Reset Device This will cause the device to reboot. This should be done after making any configuration changes, or if the device stops responding after some problems. Restore to Factory Default This will restore ALL device values to their factory defaults.
System Tab This screen allows you to: • Change the name of the Print Server. • Change the "Password" for the Print Server. • Set the Network Protocols used the selected Print Server. (Any protocols not used on your LAN may be disabled. This may improve performance.
TCP/IP Tab Selecting this tab will allow configuration for the TCP/IP network protocol. The basic options are: • Dynamic IP Address (DHCP) - The IP address is obtained automatically, from a DHCP Server on your network. • Fixed IP Address - You must enter the IP address, Subnet Mask, and Gateway Address. • IP Address - Select an unused IP address from the address range used on your LAN. • Subnet Mask - Use the same values as PCs on your LAN (or on the same LAN segment, if you have a Router).
AppleTalk Tab Generally, no Print Server configuration is required in order to use AppleTalk. This screen allows you to: • Set the Zone Name field to determine which Apple systems can gain access to this printer. • The Printer Type field is used to describe the printer driver used for each port. • Set Communication Protocol to ASCII or Binary. This must match the setting on the Apple computer systems using the Print Server.
NetBEUI Tab This screen allows you to: • Choose the Domain name for the selected Print Server. • Set how fast jobs are sent to the printer by using the Response Time field. • Set the desired option for the Abort Job if Error Occured setting. • YES causes a print job to be terminated if a printing error occurs. • NO (default) will try to continue but may cause print errors.
Internet Printing Tab The Internet Printing feature available on some models, allows you to send print jobs to the Print Server using Internet E-mail. Please see Chapter 7 - Special Features for details of using this feature.
Port Tab This screen has 2 panels - Physical Port and Logical Port. Physical Port The following settings are available: • Selected Physical Port - Select the Physical Printer Port you wish to configure. • Handshake Signal - Select Busy Only or Busy & Ack for the Physical Port. • Printer Type - Select High Speed or Low Speed for the Printer Type. Logical Port Logical Ports (printers) can be used in the Unix environment.
Chapter 6 Web-Based Management This chapter explains how to use your Web Browser to configure the Print Server Overview The Print Server incorporate the HTTP server. This allows you to connect to the Print Server and configure it using your Web Browser. Most browsers should work, provided they support tables and forms. Preparation Because it supports dynamic IP Address allocation using DHCP, BOOTP, or RARP, the Print Server ships with an IP Address of 0.0.0.0. This is NOT a valid IP Address.
Connecting to the Print Server 1. Start your Web Browser. 2. In the Address box, enter HTTP:// followed by the IP Address of the Print Server. e.g. http://192.168.0.21 3. You will then be prompted for the password. If no password has been set, just press ENTER. 4. Use the menu bar on the top of the screen to move about. Remember to save each screen before changing to a different screen.
NetBEUI Figure 30: NetBEUI Screen Domain Name Enter the designated work group to be serviced by the Print Server. This field is not case sensitive, so names with different case will be considered to be the same name. Response Time Set how fast jobs are sent to the printer. The default value of zero (0) delay should be increased only if your printer cannot cope with no delays. Abort Job if Error YES terminates a print job if a printing error occurs.
TCP/IP Figure 31: TCP/IP Screen IP Address IP Address assigned to this device. If using dynamic IP Addresses (DHCP, BOOTP, rarp), this should be left at 0.0.0.0. Subnet Mask (Network Mask) If the Router (Gateway) Address is 0.0.0.0, the Subnet Mask should also be left at 0.0.0.0. If you have a router, enter the Subnet mask for the segment to which the Print Server is attached. Gateway Address If your network segment has a router or gateways, enter its IP Address here.
Configure Server Figure 32: Configure Server Screen Print Server Name Change the default name if you wish. The new name must not contain any spaces or blanks. Password Enter the device password, and again in the Verify field. Once a password is entered, it is required in order to gain access and change the configuration. Enable Protocols Non-TCP/IP may be disabled if they are not required on your LAN. The available protocols depend on the Print Server model.
Logical Printers Logical Printers (ports) can be used under Unix. For each Logical Printer, the following fields are available: Logical Printer (Port) Select the Logical Printer Port you wish to configure. (e.g. L1) Click the Get Data button to update the display with the current data for the selected logical printer. Port Select the Printer Port which the Logical printer will use. Pre-string The printer control string (in hex) to be sent to the printer before each print job.
Chapter 7 Special Features This chapter covers the special features of the Print Server. Overview The Print Server has 2 special features: • IPP (Internet Printing Protocol). • Proprietary Internet Mail Printing system. Internet Printing Protocol(IPP) IPP (Internet Printing Protocol) is a standards-based system to allow remote printing from a PC to any accessible printer. Normally, the printer will be attached to a computer or other device which functions as an IPP Server.
IPP Client Setup - Windows 98/ME For these platforms, IPP Client software is supplied on the CD-ROM. Also you can distribute the setup program (IPP_CLIENT.EXE) to users vial E-mail. Installing from the CD-ROM 1. Insert the CD-ROM in your drive. If the program does not start automatically, run the SETUP program in the top-level folder. 2. Follow the prompts until you reach the Select Installation screen, and select IPP Client. 3. At the next screen, select the Install IPP Client option. 4.
Figure 34: Select Printer for IPP Port 6. Either select an existing printer to use the new port, and click OK. OR Click the Add New Printer button to create a new printer to use the IPP port. This will start the Add Printer wizard. Follow the prompts to complete the process. Ensure that the new printer uses the IPP port. Installation is now complete. • To create additional IPP Ports, repeat the entire procedure. • The Proxy Server and other options are set individually for each IPP Port.
IPP Client Setup - Windows 2000/XP Windows 2000 and XP have their own IPP Client, and there is no need to install the supplied IPP Client Software. To use the Windows IPP Client with the Print Server, follow this procedure: 1. Start the Add Printer wizard. 2. Select Network Printer, and click "Next" to see the Locate your Printer screen, as shown below. Figure 35: Windows 2000 - Locate your Printer 3.
5. Click "OK", and then select the printer manufacturer and model to match the printer connected to the port on the IPP Server. 6. Click "Next", and complete the Wizard. The IPP printer is now ready for use. Using IPP Printers The IPP Printer can be selected and used like any other Windows printer. If the IPP Server is not on your network, your Internet connection needs to be active.
User (Client) Requirements • Internet Connection. Either through a LAN, or dial-up. • E-Mail address. This is used to notify the user that their print job has been done, or if there any problems. • Printer Driver. Users must have a printer driver which matches the printer connected to the remote Internet Print Server. • Print Capture Software. To print more than plain text, users require InterNet Printing Port software to capture the print job and convert it into an E-Mail attachment.
User Software The software provided for remote users (InterNet Printing Port) should be installed by everyone intending to use Internet printing. Otherwise, remote users can print correctly only if: • They send an E-Mail directly to the Print Server Mail Account, using their normal E-Mail application. • The E-Mail contains plain text only. • The Internet Print Server is configured with Print every E-Mail ON. Installation of the InterNet Printing Port software will create a new printer port.
5. Remote Printer E-mail Address The E-Mail address for the Internet printer. Your print jobs will be sent to this E-Mail address. Mail Server Name or IP Address This is the name or IP Address of your Mail Server. If you are on a LAN, ask the LAN Administrator. If using a dial-up connection, use the data provided by your ISP. Your Internet E-mail Address The normal address that people use to send you E-mail.
Checking the Printer Driver To make sure that the correct printer driver for the remote printer is installed on your system, you can use the InterNet Printing Port to send an E-Mail to the Internet Printer. The procedure is as follows: 1. Connect your default printer to the InterNet Printing Port. 2. Check that "Reply Notification Mail" in the InterNet Printing Port is ON. 3. From Notepad or another text editor, print a short message (e.g. "This is a test print") to the Internet Printer.
Chapter 8 Troubleshooting This chapter describes some problem situations, which may arise, and the solutions to them. Overview If you encounter printing difficulties, please refer to the appropriate section. If, after following the advice in these documents, the Print Server still does not function properly, please contact your dealer for further advice. Hardware & LAN Problems Problem No. 1 All the Print Server's LEDs are off. Solution No. 1 Check the power supply or power connection. Problem No.
AppleTalk (Macintosh) Problem No. 1 Why do I get an incorrect printout? Solution No. 1 Some possible reasons are: • You may have chosen Binary encoding to print the file. Try to use ASCII encoding. • Some of the fonts, which are in your print file may not be supported by the printer. Try selecting LaserWriter 7 instead of LaserWriter 8. Problem No. 2 Can't find the Print Server's name in the Chooser. Solution No. 2 Try the following: 1.
Problem No. 8 Why do I have trouble printing with the LaserWriter 8? Solution No. 8 Your application software may not be compatible with the LaserWriter 8 driver or your system may not meet the requirements of the LaserWriter 8 driver. Use the Apple LaserWriter 7 driver instead. Problem No. 9 The colors on my printed output do not match the colors on my computer screen. Solution No. 9 When the printer receives a color file, it tries to match the printed output color to the screen color.
Windows Printing Problems Problem No. 1 When I tried to install the Printing software for Peer-to-Peer printing, I received an error message and the installation was aborted.. Solution No. 1 This may be caused by an existing installation of the printer port software. Before attempting another installation: • Remove the existing installation • Restart your PC To remove an existing printer port installation: 1. Open Start - Settings - Control Panel - Add/Remove Programs 2.
7. Click the Add Port button. On the resulting screen, select Other, then Printer Server, as the port to add, as shown below. 8. Click OK to see the Print Port Configuration screen, as shown below.
9. Click the Browse Device button, select the desired Print Server, and click OK. 10. Click OK to return to the Printers folders, and right-click on the Printer. Ensure that the Work off-line option is NOT checked. The Printer should no longer be grayed out, and is ready for use. Problem No. 3 I can't get my Windows-only printer to work. Solution No. 3 Many Windows-only printers cannot be networked, and so are not compatible with the Print Server.
Problem No. 5 When printing from some software applications such as Power Point, it takes a long time and the print out is incorrect. Solution No. 5 The problem is due to the printer, which is being configured to Start printing after the first page is spooled. To change this setting: • Go to Control Panel - Printers and click on your printer. • Then select File - Properties - Details. • When the Details screen appears, click the Spool Settings button.
Unix Troubleshooting Problem No. 1 Print Server device is not recognized. Solution No. 1 Check the following: • The network cable is OK. • There are no routers between the Print Server and the UNIX host during IP address assignment. • There are no NetWare File Servers without TCP/IP support between the Print Server and the UNIX host. • You have used the correct hardware address, as shown on a sticker on the base of the device.
Appendix A Specifications General Specifications TE100-P1U Print Server Power Consumption 5.5w max. External Power Adapter 9V DC LEDs 2 USB Port (1.1) 1 Ethernet Connector 10/100BaseT FCC / CE FCC, CE.
Parallel Port Pin Assignments TE100-P1P Print Server ∗ Pin Signal Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19-30 31 32 33-35 36 -Strobe +Data 1 +Data 2 +Data 3 +Data 4 +Data 5 +Data 6 +Data 7 +Data 8 - ACK + Busy + Paper Error + Select -Auto Feed Not Defined Logic GND Chassis GND Peripheral Logic High GND -Init -Fault Not Defined -SelectIn Source H Bi-Di* Bi-Di* Bi-Di* Bi-Di* Bi-Di* Bi-Di* Bi-Di* Bi-Di* P P P P H P H P H Data signals will be driven by some but not all peripheral devices.
Appendix B Windows Server Configuration Windows NT 4.0 Server If using Windows NT 4.0, Microsoft TCP/IP Printing Support must be installed. • If it is already installed, add a TCP/IP Remote Printer, as described below. • Otherwise, install TCP/IP printing support, then add a TCP/IP Remote Printer. Adding TCP/IP Printing Support 1. Go to Start-Settings-Control Panel-Network. 2. Click the Service option and ensure that Microsoft TCP/IP Printing is enabled.
Windows 2000/2003 Server 1. Start the Add Printer Wizard, select Network Printer, then click Next to browse for the Print Server. 2. Locate and double-click the Print Server, select the desired port, and click Next. A message like the following will be displayed: Figure 40: Windows 2000 Message Figure 41: Windows2003 Message 3. Click "OK", and select the correct Manufacturer and Model for this printer. 4. Follow the prompts to complete the installation. 5.
Appendix C Unix Systems Overview Your Wireless Print Server supports the LPD Unix printing method, which is supported by all common Unix systems. You must configure both the Wireless Print Server itself and your Unix system, as described in the following sections. Print Server IP Address Configuration Because it supports dynamic IP Address allocation using DHCP or BOOTP, the Print Server ships with an IP Address of 0.0.0.0. This is NOT a valid IP Address.
LPD Printing LPD is a built-in printing protocol for most UNIX systems. Configuration for the most common platforms is described below. LPD on IBM AIX 4.15 Before proceeding, ensure that the Print Server has been assigned an IP Address. To setup your AIX system for LPD printing, perform the following steps. 1. Add the Print Server to /etc/hosts.lpd, using the name you assigned to the Print Server. 2. Start the LPD daemon if it is not running, using the following command: start src -s qdaemon 3.
LPD on System V Before beginning LPD Setup, ensure that an IP Address has been assigned to the Print Server. Keep the following points in mind: The remote host name is the name of the Print Server. The remote printer name is the print queue name for the Logical Printer. Logical printers also need to be configured on the Print Server itself. If your UNIX asks for the LPD type, be sure to identify the service type as BSD. The Print Server’s LPD protocol meets BSD system standards.
Where: Printer_name is the Print Queue name used to store jobs for the corresponding logical printer. PS_NAME is the Print Server name defined in /etc/hosts. Logical_Printer_name is the logical printer name on the Print Server. (e.g. L1) Spooler_directory is the directory you created in Step 6.
LPD on BSD Before continuing, ensure that an IP Address has been assigned to the Print Server. Remember the following: The remote host name is the name of the Print Server. The remote printer name is the logical printer (e.g. L1) on the Print Server. If asked for the LPD type, enter the service type as BSD. In the sample commands shown, printer_name is the Print Queue serviced by the logical printer on the Print Server, and Spooler_dir is the name of the directory, which is used to spool the print jobs.
Example: Marketing|RP1_PS123456:\ [TAB] :lp=:\ [TAB] :rm=PS_Rm203:\ [TAB] :rp=L1:\ [TAB] :sd=/usr/spool/Marketing:\ [TAB] :mx#0: Repeat this process for each Logical Printer/Print Queue combination that you wish to create. Printing using LPD For LPD printing instructions, refer to your UNIX manual. The following example is for a BSD system: lpr -P printer_name filename Where: printer_name is the name of the Print Queue defined on the Unix host. filename is the name of the file you wish to print.
Appendix D NetWare Overview • The Print Server must be configured as a valid device on your TCP/IP network. This printing method uses LPR over TCP/IP, not the Netware protocol. • To use NDPS (Novell Distributed Printing Services), the Novell server must be running Novell NetWare 5, and the PCs (clients) must be running IntranetWare Client V2.2. or later. The following procedure is designed to enable Public Access Printing under NDPS.
To start the NDPS Manager whenever you bring up the server, add a command like the following to your server's AUTOEXEC.NCF file: LOAD NDPSM SerMGR.TeSupp The last item is the name of the NDPS Manager object you wish to load. 9. After creating an NDPS Manager, you can create NDPS printers by using NetWare Administrator, as explained below. Creating an NDPS Printer Agent To create Public Access Printers using the NDPS Manager Object in NetWare Administrator, follow this procedure: 1.
10. In the Host address IP field, enter the IP Address previously assigned to the Print Server device. 11. In the Printer Name field, enter the Logical Port name on the Print Server. (L1 for Port 1, L2 for port 2). 12. Click Finish, then select appropriate drivers for Windows 98 etc as required. 13. The new Printer Agent will now appear in the Printer Agent List window. Repeat this procedure for any other ports on the Print Server, or for any other logical printers you wish to use.
