Quick Installation Guide TE100-MP1U TE100-MP2U TEW-MP2U
Table ofofContents Table Contents English ....................................................................................................................................................... 1 1. Before You Start ................................................................................................................................ 2. How to Connect ................................................................................................................................. 3.
1. Before You Start Package Contents System Requirements Note: 1. Do not install MFP Server Control Center, connect printer to print server and connect the computer to the print server until instructed to do so. 2. The MFP Server Control Center must be installed on each computer in order to use your multi-function printer.
Application 54Mbps 802.11g Wireless 2-Port Multi-Function USB 2.0 Print Server (TEW-MP2U) Workstation with Wireless PCI Adapter (TEW-423PI) Multi-Functional External USB 2.0 USB 2.0 Printer Storage Drive Internet Notebook with Wireless PC Card (TEW-421PC) 54Mbps 802.11g Wireless Firewall Router (TEW-432BRP) Cable/DSL Modem 1 or 2 Port 10/100Mbps Multi-Function USB 2.
2. How to Connect 1. Install the printer drivers to your computer. Then shutdown the printer and disconnect the printer from your computer. Note: Please refer to your printer's manual for printer installation instructions. 2. Connect the Power Adapter to the Print Server and then to a power outlet. 3. Connect a RJ-45 network cable from a Switch/Router to the LAN port of the Print Server. 4. Connect the USB Printer to the USB port of the Print Server. 5. Power ON printer. 6.
3. Configure the Print Server 1. Insert the Utility CD-ROM into your computer's CD-ROM Drive and then click Install Utility. 2. Follow the InstallShield Wizard instructions. Then click Finish. 3. Click the Print Server and click Configure Server. 4. Enter the User name and Password, and then click Login.
5. Click TCP/IP. Assign the Print Server a Static IP address and then click Apply. Note: The IP Address must match the same network segment as your computer. 6. Click Yes to restart the Print Server. 7. Cllick Close. Note: For the TEW-MP2U, proceed to section 5. Print Server configuration is now complete. For detailed information regarding the TE100-MP1U/TE100-MP2U configuration and advanced settings, please refer to the User's Guide on the Utility CD-ROM or TRENDnet's website at www.trendnet.
4. Configure Wireless Settings (TEW-MP2U only) 1. Click the Print Server and click Configure Server. 2. Enter the User name and Password, and then click Login. User Name: admin Password: admin 3. Click Wireless. Select your Region or Domain to meet your country's regulations. Enter the SSID of your wireless network. If encryption is enabled on your wireless network, select WEP or WPA-PSK and enter your encryption key. Then click Apply.
5. Cllick Close. 6. Unplug the power to the Print Server, disconnect the Ethernet cable to the Print Server, wait 15 seconds, then plug power to the Print Server back in. 7. Verify the WLAN LED is lit on the Print Server. Print Server wireless configuration is now complete. For detailed information regarding the TEW-MP2U configuration and advanced settings, please refer to the User's Guide on the Utility CD-ROM or TRENDnet's website at www.trendnet.
5. Printing Note: 1. For LPR, IPP and Manual connect printing instructions, please refer to the User Guide. The User Guide is included on the Utility CD-ROM. 2. A computer using LPR or IPP printing and a computer using NetUSB printing can not print documents to the same printer simultaneously. Setup for Auto Connect Printing Note: Only one user can print at a time in Auto Connect mode. Once a user has finished printing, another user can print or scan to the printer. 1. Select the printer.
4. User can now start printing. 5. Select the printer. Then click Disconnect. (optional) Note: For Auto Connect Printing, a user does not have to wait for the current owner to click disconnect. Follow step 1 to grab ownership of the Print Server.
6. Faxing 1. Select the printer. Then click Connect. 2. Open the document that you wish to fax and click Print. 3. Select your fax as the printer. 4. Your Multi-Function Printer's fax software will appear. Follow the fax software instructions for sending a fax. 5. Select the printer. Then click Disconnect.
7. Scanning 1. Select the printer. Click Network Scanner. 2. Select TWAIN or WIA format and click OK. 3. Place the document on the MultiFunction Printer's Scanner bed. 4. Type in a name, select image type and choose the desired path. Then click Scan. 5. The multi-function printer scanner software will appear. Follow the scanner software instructions. 6. Repeat steps 3, 4 and 5 to scan additional documents. Otherwise, click Close. 7. Select the printer. Then click Disconnect.
8. Storage Selecting Mode 1. Select the Print Server and click Configure Server. 2. Click Supported Protocols, select Server Mode or NetUSB Mode and then click apply. 3. Click Yes to restart the Print Server. Server Mode 1. Click Network Storage. 2. Right click the USB storage icon and select Map Network Drive.
3. Select the desired drive letter and then click Finish. NetUSB Mode Note: Only one user can connect to the storage device at a time in NetUSB mode. 1. Click Connect. 2. Select Open folder to view files using Windows Explorer and then click OK. 3. Click Disconnect to disconnect from the storage device.
Troubleshooting Q1. The Multi-Function Print (MFP) Server Control Center does not detect the Print Server and/or printer/storage device. What should I do? A1. First, double check your hardware connections; make sure that the Print Server and printer are powered ON and are properly connected. Make sure the RJ-45 network cable is securely connected to the Print Server and Switch/Router. Second, disable any software firewall programs such as ZoneAlarm or Norton Internet Security.
Q6. I configured my print server to automatically receive an IP Address from a DHCP server, and now I cannot go into the print server’s web utility. A6. Open the USB MFP Server Control Center (See 3. Configure the Print Server) to locate your print server’s IP Address. Q7. What is the difference between Auto Connect Network & Manual Connect modes? A7. If user A chooses auto connect (printing or scanning), other users can print or scan after User A has finished printing or scanning.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
TRENDnet Technical Support US . Canada Toll Free Telephone: 1(866) 845-3673 24/7 Tech Support Europe (Germany . France . Italy . Spain . Switzerland UK) Toll Free Telephone: +00800 60 76 76 67 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Worldwide Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Francais/Deutsch - 11am-8pm, Monday - Friday MET Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.
