TRENDnet User’s Guide Cover Page
Table of Contents TRENDnet User’s Guide Thank you for purchasing your new TRENDnet Web Smart Switch! Contents Web Smart Switch Series Product Overview ..................................... i TEG-082WS Overview ......................................................................................................i Package Contents ..................................................................................................i TEG-082WS Hardware Features ..................................................
TRENDnet User’s Guide IPv4 ARP Aging Time ............................................................................................ 9 IPv4 Static ARP ..................................................................................................... 9 IPv4 Static/Default Route .................................................................................. 10 Set your IPv6 settings ........................................................................................ 11 Add IPv6 neighbors .........
TRENDnet User’s Guide Enable loopback detection ................................................................................ 49 Static Unicast ............................................................................................................... 50 Add static unicast entries to the switch ............................................................. 50 Static Multicast ............................................................................................................
TRENDnet User’s Guide Security......................................................................................... 80 Table of Contents Firmware Upgrade ....................................................................................................... 96 Configure Port Access Control ........................................................................... 80 Upgrade your switch’s firmware .......................................................................
Web Smart Switch Series TRENDnet User’s Guide Web Smart Switch Series Product Overview TEG-082WS Hardware Features TEG-082WS Overview Front View Rear View Package Contents In addition to your switch, the package includes: Quick Installation Guide CD-ROM (Utility & User’s Guide) Power cord (1.8 m / 6 ft.) Rack mount kit If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased.
TRENDnet User’s Guide Web Smart Switch Series Link/Activity Green on : When the SFP LED is on, the link established using the SFP module is operating at 1Gbps speed. Green blinking : When the SFP LED is blinking, the port is transmitting or receiving data on through the 1Gbps link established. Amber on When the SFP LED is on, the link established using the SFP module is operating at 100Mbps speed.
Web Smart Switch Series TRENDnet User’s Guide TEG-204WS Overview TEG-204WS Hardware Features Front View Rear View Package Contents In addition to your switch, the package includes: Quick Installation Guide CD-ROM (Utility & User’s Guide) Power cord (1.8 m / 6 ft.) Rack mount kit If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased.
Web Smart Switch Series TRENDnet User’s Guide SFP Slots (17F-20F) Link/Activity Green on : When the SFP LED is on, the link established using the SFP module is operating at 1Gbps speed. Green blinking : When the SFP LED is blinking, the port is transmitting or receiving data on through the 1Gbps link established. Amber on When the SFP LED is on, the link established using the SFP module is operating at 100Mbps speed.
Web Smart Switch Series TRENDnet User’s Guide TEG-284WS Overview TEG-284WS Hardware Features Front View Rear View Package Contents In addition to your switch, the package includes: Quick Installation Guide CD-ROM (Utility & User’s Guide) Power cord (1.8 m / 6 ft.) Rack mount kit If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased.
Web Smart Switch Series TRENDnet User’s Guide SFP Slots (25F-28F) Link/Activity Green on : When the SFP LED is on, the link established using the SFP module is operating at 1Gbps speed. Green blinking : When the SFP LED is blinking, the port is transmitting or receiving data on through the 1Gbps link established. Amber on When the SFP LED is on, the link established using the SFP module is operating at 100Mbps speed.
Web Smart Switch Series TRENDnet User’s Guide TEG-524WS Overview TEG-524WS Hardware Features Front View Rear View Package Contents In addition to your switch, the package includes: Quick Installation Guide CD-ROM (Utility & User’s Guide) Power cord (1.8 m / 6 ft.) Rack mount kit If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased.
TRENDnet User’s Guide Web Smart Switch Series Diagnostic LEDs Power LED On : When the Power LED is on, the device is receiving power. the Power turns off, the power cord is not Off : When connected or the device is not receiving power. Gigabit Ethernet Port LEDs (1-52) Link/Activity Green on : When the Green LED is on, the respective port is connected to a 1Gbps Ethernet network. Amber : When the Green LED lights on, the respective port is on connected to a 10/100Mbps Ethernet network.
TRENDnet User’s Guide Web Smart Switch Series Switch Installation Rack Mount Hardware Installation Desktop Hardware Installation The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipment. Attach the mounting brackets at the switch’s front panel (one on each side), and secure them with the provided screws. The site where you install the hub stack may greatly affect its performance.
Web Smart Switch Series TRENDnet User’s Guide Basic IP Configuration 5. Enter the User Name and Password, and then click Login. By default: User Name: admin Password: admin Note: User name and password are case sensitive. 6. Click System, L3 Feature, and then click IPv4 Interface. 3. Assign a static IP address to your computer’s network adapter in the subnet of 192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0. 4.
TRENDnet User’s Guide 7. Click on Edit for interface vlan1. Note: All other functions of this page will be explained in detail in its respective section. Web Smart Switch Series 9. When the confirmation message appears click OK. Be sure to re-log back into the switch using the new IP address and save the configuration to your flash. NOTE: The configured settings are only applied to the switch’s temporary memory and will be lost upon the next power-cycle.
TRENDnet User’s Guide Web Smart Switch Series Connect additional devices to your switch You can connect computers or other network devices to your switch using Ethernet cables to connect them to one of the available Gigabit Ethernet Ports, Gigabit Ethernet PoE Ports, Gigabit Ethernet PoE+ Ports, Gigabit Ethernet UPoE Ports, or SFP Ports. Check the status of the LED indicators on the front panel of your switch to ensure the physical cable connection from your computer or device.
Web Smart Switch Series TRENDnet User’s Guide Accessing switch management interfaces Access your switch management page Note: Your switch default management IP address http://192.168.10.200 is accessed through the use of your Internet web browser (e.g. Internet Explorer®, Firefox®, Chrome™, Safari®, Opera™) and will be referenced frequently in this User’s Guide. Throughout this user’s guide, the term Web Configuration will be used to reference access from web management page. 1.
Web Smart Switch Series TRENDnet User’s Guide Administration Information System Name – Displays the identifying system name of your switch. This information can be modified under the System section. System Location - Displays the identifying system location of your switch. This information can be modified under the System section. System Contact – Displays the identifying system contact or system administrator of your switch. This information can be modified under the System section.
Web Smart Switch Series TRENDnet User’s Guide System System Management Set your system information System > System Management This section explains how to assign a name, location, and contact information for the switch. This information helps in identifying each specific switch among other switches in the same local area network. Entering this information is optional. 1. Log into your switch management page (see “Access your switch management page” on page 5). 4. Click Apply. 2.
Web Smart Switch Series TRENDnet User’s Guide L3 Feature IPv4 Interface System > L3 Feature > IPv4 Interface This section allows you to change your switch IPv4 address settings and additionally create and assign the aforementioned address to VLANs. Typically, the IP address settings should be changed to match your existing network subnet in order to access the switch management page on your network. Default Switch IPv4 Address: 192.168.10.200 5. Review the settings.
Web Smart Switch Series TRENDnet User’s Guide IPv4 ARP Aging Time IPv4 Static ARP System > L3 Feature > IPv4 ARP Aging Time System > L3 Feature > IPv4 Static ARP This section allows you to set the timeout for the switch’s ARP Table per each configured VLAN. This section allows you to statically set ARP entries per each configured VLAN. 1. Log into your switch management page (see “Access your switch management page” on page 5). 1.
TRENDnet User’s Guide IPv4 Static/Default Route Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. System > L3 Feature > IPv4 Static/Default Route This section allows you to set your switch’s IPv4 routing table default gateway IP address, or specify a static route. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, L3 Feature, and then IPv4 Static/Default Route. 3. Review the settings.
Web Smart Switch Series TRENDnet User’s Guide Set your IPv6 settings System > L3 Feature > IPv6 Interface Internet Protocol version 6 (IPv6) is a new IP protocol designed to replace IP version 4 (IPv4). The IPv6 address protocol meets the current requirements of new applications and the never ending growth of the Internet. The IPv6 address space makes more addresses available but it must be approached with careful planning. Successful deployment of IPv6 can be achieved with existing IPv4 infrastructures.
Web Smart Switch Series TRENDnet User’s Guide NS Retransmit Time: A constant that defines a nonzero number of seconds between periodic reauthentication of the client. The field is 1~3600 seconds. The default setting is 1 second. Add IPv6 neighbors System > L3 Feature > IPv6 Neighbor This settings allows you to manually define IPv6 supported neighboring devices on your network. 1. Log into your switch management page (see “Access your switch management page” on page 5).
Web Smart Switch Series TRENDnet User’s Guide Configure IPv6 Routing Table System > L3 Feature > IPv6 Static/Default Route This section allows you to set your switch’s IPv6 routing table default, or specify a static route. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, L3 Feature, and then IPv6 Static/Default Route. 4. At the bottom of the left hand panel, click Save. 3. Review the settings.
Web Smart Switch Series TRENDnet User’s Guide 4. At the bottom of the left hand panel, click Save. DNS Set your DNS server settings System > DNS This setting allows you to configure your IPv4/IPv6 DNS server settings for the purpose or resolving hostnames. For example, when specifying your SNTP server time settings via domain name, the switch will not be able to resolve the SNTP domain name specified until you configure the switch DNS server setting. 5.
TRENDnet User’s Guide IP Access List Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. Restrict access to switch management page System > IP Access List This section allows you to define or restrict access to the switch management page to a list of specific IP addresses. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, and click on IP Access List. 3. Review the settings.
Web Smart Switch Series TRENDnet User’s Guide Administration To create additional administrative user accounts: Change administrator password and add accounts User Name: Enter the user name of the new account. System > Administration Password: Enter the password for the new acocunt and enter the password again the Confirm Password field to verify. Then, click Add to add to the table. For additional user accounts, you will be provided the option to Modify or Delete to remove the account.
Web Smart Switch Series TRENDnet User’s Guide Timeout System Time Change web idle login timeout settings Set the switch date and time System > Timeout System > System Time This section explains how to modify the switch management page idle timeout settings. 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, and click on System Time. 2.
Web Smart Switch Series TRENDnet User’s Guide o To: Set the daylight savings end date and time. DST Offset: Click the drop-down list to set the time offset based on respective time zone. SNTP – Allows you to configure your switch to pull time and date settings automatically from a network time server. If selecting this option, under Simple Network Time Protocol (SNTP) Settings, enter your time server settings.
TRENDnet User’s Guide Web Smart Switch Series SSL Enable HTTPS/SSL (Secure Socket Layer) management access System > SSL Click Continue, Proceed to this website, and accept the certificate if prompted. By default, your switch management page can be accessed using standard web HTTP protocol which is unsecure.
TRENDnet User’s Guide SSH Enable SSH (Secure Shell) management access Web Smart Switch Series 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. System > SSH 1. Log into your switch management page (see “Access your switch management page” on page 5). 2.
TRENDnet User’s Guide Telnet Enable Telnet management access Web Smart Switch Series 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. System > Telnet 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, and click on Telnet.
TRENDnet User’s Guide DHCP Auto Configuration Enable DHCP Auto Configuration System > DHCP Auto Configuration If you need to automatically update the switch configuration files via a remote server, the DHCP Auto Configuration feature is available for this purpose via the DHCP server. Your IP address settings must enable the DHCP client so that this feature can operate with your DHCP server. Web Smart Switch Series 5.
TRENDnet User’s Guide Web Smart Switch Series System Log View and setup your switch logging System > System Log The system log is designed to monitor the operation the switch by recording the event messages it generates during normal operation. These events may provide vital information about system activity that can help in the identification and solutions of system problems. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2.
Web Smart Switch Series TRENDnet User’s Guide SNMP Engine ID (10-64 Hex Characters) – Enter the local device Engine ID. The field value is a hexadecimal string. Each byte in hexadecimal character strings is two hexadecimal digits. The Engine ID must be defined before SNMP is enabled. Reset to Default – Use the device-generated Engine ID (Reset to Default will override any entry in the Engine ID field).
Web Smart Switch Series TRENDnet User’s Guide View Modifying SNMP View Table Entries System > SNMP > View If you need to modify an entry in the View Table page, you must first delete the entry and then re-enter it. The SNMP View table specifies the MIB object access criteria for each View Name. If the View Name is not specified on this page, then it has access to all MIB objects. You can specify specific areas of the MIB that can be accessed or denied based on the entries in this table.
Web Smart Switch Series TRENDnet User’s Guide Group System > SNMP > Group The SNMP View Names are defined in the SNMP Group Access table and are based on the User and Group Names 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, click on SNMP, and click on Group. 3. Review the settings. Creating SNMP View Names Modifying SNMP View Names Before you can create an SNMP View name, you must define a Group Name using the SNMP User/Group page.
Web Smart Switch Series TRENDnet User’s Guide User System > SNMP > User Click Add. The new User Name and Group Name are displayed on the SNMP User/Group page. An SNMP User Name and Group Name definition is the basis for all the other SNMP tables. You can create and delete View Names by following the procedures in the following sections: 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, click on SNMP, and click on User. 3.
Web Smart Switch Series TRENDnet User’s Guide Community Modify SNMP Community Settings System > SNMP > Community If you need to modify a Community Table entry, you must first delete the entry by using the procedure below and then re-enter it with the modification by creating a new Community table entry. A community string has attributes for controlling who can use the string and what the string will allow a network management station to do on the switch.
Web Smart Switch Series TRENDnet User’s Guide Trap System > SNMP > Trap A Host IP address is used to specify a management device that needs to receive SNMP traps sent by the switch. This IP address is associated with the SNMP Version and a valid Community Name in the Host table of the switch. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, click on SNMP, and click on Trap. 3. Review the settings.
TRENDnet User’s Guide RMON Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. Settings System > RMON > Settings The RMON (Remote MONitoring) MIB is used with SNMP applications to monitor the operations of network devices. The Switch supports the four RMON MIB groups listed here: Statistic group— This group is used to view port statistics remotely with SNMP programs.
TRENDnet User’s Guide Statistics System > RMON > Statistics You can remotely view individual port statistics with RMON by using your SNMP NMS software and the RMON portion of the MIB tree. Web Smart Switch Series In the list, you can click Modify to modify an entry or click Delete or delete the entry. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages. 1.
Web Smart Switch Series TRENDnet User’s Guide History Click Add to add the entry to the table. System > RMON > History RMON histories are snapshots of port statistics. They are taken by the switch at predefined intervals and can be used to identify trends or patterns in the numbers or types of ingress packets on the ports on the switch. The snapshots can be viewed with your SNMP NMS software with the history group of the RMON portion of the MIB tree. A history group is divided into buckets.
Web Smart Switch Series TRENDnet User’s Guide Alarms System > RMON > Alarms RMON alarms are used to generate alert messages when packet activity on designated ports rises above or falls below specified threshold values. The alert messages can take the form of messages that are entered in the event log on the switch or traps that are sent to your SNMP NMS software or both. RMON alarms consist of two thresholds. There is a rising threshold and a falling threshold.
Web Smart Switch Series TRENDnet User’s Guide Click Add to add the entry to the table. Events System > RMON > Event An event specifies the action of the switch when the ingress packet activity on a port crosses a statistical threshold defined in an alarm. The choices are to log a message in the event log of the switch, send an SNMP trap to an SNMP workstation, or both.
TRENDnet User’s Guide Click Add to add the entry to the table. Web Smart Switch Series 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK. Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. In the list, you can click Modify to modify an entry or click Delete or delete the entry.
TRENDnet User’s Guide Web Smart Switch Series Statistics Statistics provide important information for troubleshooting switch problems at the port level. The Web Management Utility provides a two statistics charts, including Traffic Information and Error Information. Traffic System > Statistics > Traffic 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, click on Statistics, and click on Traffic. 3. View the Traffic Information Statistics.
TRENDnet User’s Guide Error Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. System > Statistic > Error 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, click on Statistics, and click on Error. 3. View the Error Information Statistics. InErrors: Inbound Errors (Pkts), number of inbound errors in packets per second. OutErrors: Outbound Errors (Pkts), number of outbound error packets.
TRENDnet User’s Guide IEEE 802.3az EEE Enable IEEE 802.3az Power Saving Mode System > IEEE 802.3az EEE The IEEE 802.3 EEE standard defines mechanisms and protocols intended to reduce the energy consumption of network links during periods of low utilization, by transitioning interfaces into a low-power state without interrupting the network connection. The transmitted and received sides should be IEEE802.3az EEE compliance. By default, the switch disabled the IEEE 802.3az EEE function.
Web Smart Switch Series TRENDnet User’s Guide Network o Up -This parameter indicates a valid link exists between the port and the end node. o Down -This parameter indicates the port and the end node have not established a valid link. Physical Interface Configure Physical Interfaces Network > Physical Interface This section allows you to configure the physical port parameters such as speed, duplex, flow control, and jumbo frames.
Web Smart Switch Series TRENDnet User’s Guide o 100/Half -This parameter indicates the port is configured for 100Mbps operation in half-duplex mode. o 10/Half -This parameter indicates the port is configured for 10Mbps operation in half-duplex mode. o EAP: This parameter reflects the current Extensible Authentication Protocol (EAP) setting on the port. The possible values are: o Ignore - This parameter indicates that the All setting does not apply to the EAP field.
Web Smart Switch Series TRENDnet User’s Guide Spanning Tree Protocol Network > Spanning Tree > Protocol Spanning Tree Protocol (STP) provides network topology for any arrangement of bridges/switches. STP also provides a single path between end stations on a network, eliminating loops. Loops occur when alternate routes exist between hosts. Loops in an extended network can cause bridges to forward traffic indefinitely, resulting in increased traffic and reducing network efficiency. 1.
Web Smart Switch Series TRENDnet User’s Guide Port External Cost: This defines a metric that indicates the relative cost of forwarding packets to the specified port list. Port cost can be set automatically or as a metric value. Define a value between 1 and 200000000 to determine the external cost. The lower the number, the greater the probability the port will be chosen to forward packets. The default port cost: 100Mbps port = 200000. Gigabit port = 20000.
Web Smart Switch Series TRENDnet User’s Guide P2P: Choosing the Forcetrue parameter indicates a point-to-point (P2P) shared link. P2P ports are similar to edge ports however they are restricted in that a P2P port must operate in full-duplex. Like edge ports, P2P ports transition to a forwarding state rapidly thus benefiting from RSTP. A P2P value of Forcefalse indicates that the port cannot have P2P status.
Web Smart Switch Series TRENDnet User’s Guide Instance Network > Spanning Tree > Instance 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on System, click on Spanning Tree, and click on Instance. MST Table: Make changes to the table entry, and click Apply modify or click Delete to remove the ID entry. 4. At the bottom of the left hand panel, click Save. 3. View your MSTP instance information.
TRENDnet User’s Guide Web Smart Switch Series MST Port Network > Spanning Tree > MST Port 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on Spanning Tree, and click on MST Port. 3. Review the settings. For each entry, click Apply to save changes. Select MST Port – Click the drop-down to select which MST port to configure. MST Port Info - The MST Port Information page provides user to configure the MSTP Interface settings.
Web Smart Switch Series TRENDnet User’s Guide Trunk The trunking function enables the cascading of two or more ports for a combined larger total bandwidth. Up to 8 trunk groups may be created, each supporting up to 8 ports. Add a trunking Name and select the ports to be trunked together, and click Apply to activate the selected trunking groups. Important Note: Do not connect the cables of a port trunk to the ports on the switch until you have configured the ports on both the switch and the end nodes.
Web Smart Switch Series TRENDnet User’s Guide Status Port Priority Network > Trunk > Status Network > Trunk > Port Priority 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on Trunk, and click on Status. 2. Click on Network, click on Trunk, and click on Port Priority. 3. View your trunk group status information. 3.
TRENDnet User’s Guide Web Smart Switch Series Mirroring Configure port mirror settings Network > Mirroring Port mirroring allows you to monitor the ingress and egress traffic on a port by having the traffic copied to another port where a computer or device can be set up to capture the data for monitoring and troubleshooting purposes. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, and click on Mirroring. 3. Review the settings.
TRENDnet User’s Guide Loopback Detection Enable loopback detection Network > Loopback Detection The loopback detection feature allows the switch to detect and prevent disruption from loops that occur on uplink or downlink switches directly connected to your switch. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network and click on Loopback Detection.
TRENDnet User’s Guide Static Unicast Add static unicast entries to the switch Network > Static Unicast Web Smart Switch Series In the list, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all the entries in the list. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide Static Multicast Add static multicast entries to the switch Network > Static Multicast Web Smart Switch Series In the list, you can click Modify to modify an entry or click Delete or delete the entry. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages. In this section, you can add static multicast entries to the switch configuration. 1.
TRENDnet User’s Guide Web Smart Switch Series IGMP Snooping Settings Network > IGMP Snooping > Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on IGMP Snooping, and click on Settings. 3. Review the settings. Click Apply to save the settings. Status – Click the drop-down list and select Enabled to enable the IGMP snooping feature or Disabled to disable the feature.
TRENDnet User’s Guide Router Ports Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. Network > IGMP Snooping > Router Port 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on IGMP Snooping, and click on Router Port. 3. Review the settings. Click Apply to save the settings. In the VLAN ID router port list, you can configure your Static and Dynamic Router ports.
TRENDnet User’s Guide Web Smart Switch Series MLD Snooping Settings Network > MLD Snooping > Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on MLD Snooping, and click on Settings. 3. Review the settings. Click Apply to save the settings. MLD Snooping Status – Click the drop-down list and select Enabled to enable MLD snooping. Aging Timeout – Enter the aging timeout in seconds.
TRENDnet User’s Guide Router Port Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. Network > MLD Snooping > Router Port 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on MLD Snooping, and click on Router Port. 3. Review the settings. Click Modify to change the settings. Click Apply to save the settings. VLAN ID – Shows the VLAN ID. Static Router Port – Shows if/what the static router ports are.
Web Smart Switch Series TRENDnet User’s Guide Multicast VLAN Multicast VLAN Table Multicast VLAN Settings Network > Multicast VLAN > Multicast VLAN Table Network > Multicast VLAN > Multicast VLAN Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on Multicast VLAN, and click on Multicast VLAN Table. 2.
Web Smart Switch Series TRENDnet User’s Guide 4. At the bottom of the left hand panel, click Save. Multicast VLAN Access Settings Network > Multicast VLAN > Multicast VLAN Access Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on Multicast VLAN, and click on Multicast VLAN Access Settings. 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK.
Web Smart Switch Series TRENDnet User’s Guide Multicast Filtering Bandwidth Control Multicast Filtering Storm Control Network > Multicast VLAN > Multicast VLAN Settings Network > Bandwidth Control > Storm Control 1. Log into your switch management page (see “Access your switch management page” on page 5). This section allows you to configure the DLF (Destination Lookup Failure), broadcast, and multicast storm settings for each switch port. 2.
Web Smart Switch Series TRENDnet User’s Guide Ingress Rate Limiting Egress Rate Limiting Network > Bandwidth Control > Ingress Rate Limiting Network > Bandwidth Control > Egress Rate Limiting This section allows you to set the ingress (receive) rate for each switch port. This section allows you to set the egress (transmit) rate for each switch port. 1. Log into your switch management page (see “Access your switch management page” on page 5). 1.
Web Smart Switch Series TRENDnet User’s Guide VLAN Tagged/Untagged/Not Member VLAN Ports Tagged On a port, the tag information within a frame is examined when it is received to determine if the frame is qualified as a member of a specific tagged VLAN. If it is, it is eligible to be switched to other member ports of the same VLAN. If it is determined that the frame’s tag does not conform to the tagged VLAN, the frame is discarded.
Web Smart Switch Series TRENDnet User’s Guide Select the not member ports to restrict from the new VLAN. Port Network > VLAN > Port In this section, you can modify the port VID settings, acceptable frame types, and ingress filtering. 1. Log into your switch management page (see “Access your switch management page” on page 5). Click Apply to save the new VLAN to the table. 2. Click on Bridge, click on VLAN, and click on Port Settings.
Web Smart Switch Series TRENDnet User’s Guide Forwarding Dynamic Network > VLAN > Forwarding Network > VLAN > Dynamic This section allows you to configure your switch to standard 802.1Q VLAN mode (IVL) or Asymmetric VLAN mode (SVL). Asymmetric VLAN allows the configuration of overlapping untagged VLAN ports in order to create VLAN groups. It is recommended to use the standard 802.1Q VLAN mode when possible.
Web Smart Switch Series TRENDnet User’s Guide Private Click on the Forwarding Ports ratio button that applies to your configuration. Network > VLAN > Private Click Apply. The private VLAN feature allows you to create a more secure VLAN that is completely isolated to its members and cannot communicate with other VLANs. A private VLAN partitions the Layer 2 broadcast domain of a VLAN into subdomains, allowing you to isolate the ports on the switch from each other.
Web Smart Switch Series TRENDnet User’s Guide Current GVRP Network > VLAN > Current GVRP Global Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). Network > GVRP > GVRP Global Settings 2. Click on Network, click on VLAN, and click on Current. 3. View the current VLAN database in the table.
TRENDnet User’s Guide Web Smart Switch Series Port Settings Network > GVRP > Port Settings This section will allow you to select which ports will have GVRP enabled or will be restricted from using GVRP. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on GVRP and click on Port Settings. 3. Review the settings for each port. Click Apply to save the settings. Port - This parameter displays the ports on the switch.
TRENDnet User’s Guide Web Smart Switch Series Time Settings Network > GVRP > Time Settings This section will allow you to define the GARP Join, Leave, and Leave All Time for each port. Note: The GARPLeaveTimer must be greater than (GARPJoinTimer x2 + 10) and the GARPLeaveAllTimer must be greater than (GARPLeaveTimer + 10). The acceptable input values are multiples of 10. If you try to enter a value that is not a multiple of 10, the value is rounded down 1.
Web Smart Switch Series TRENDnet User’s Guide Voice VLAN This chapter contains a description of the Switch’s Voice VLAN feature and the procedures to create, modify, and delete a voice VLAN configuration. The Voice VLAN feature is specifically designed to maintain high quality, uninterrupted voice traffic through the switch. When talking on a voice over IP phone, a user expects to have no interruptions in the conversation and excellent voice quality.
Web Smart Switch Series TRENDnet User’s Guide Note: Link Layer Discovery Protocol for Media Endpoint Devices (LLDP- MED) is not supported on the switch. Each IP phone that is VLAN aware should be manually configured for the VLAN ID that matches your voice VLAN ID. Each of the voice VLAN ports connected to an IP phone should be configured as “Not Member” ports of the tagged VLAN. port will be removed from the voice VLAN. The range is 1 to 120 hours.
Web Smart Switch Series TRENDnet User’s Guide OUI Network > Voice VLAN > OUI 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, Voice VLAN, and click on OUI. 3. Review the settings. 4. At the bottom of the left hand panel, click Save. 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK.
Web Smart Switch Series TRENDnet User’s Guide LLDP Enable and configure LLDP Link Layer Discovery Protocol (LLDP) allows Ethernet network devices, such as switches and routers, to receive and transmit device-related information to directly connected devices on the network and to store data that is learned about other devices. 4. At the bottom of the left hand panel, click Save. Settings Network > LLDP > Settings 1. Log into your switch management page (see “Access your switch management page” on page 5).
Web Smart Switch Series TRENDnet User’s Guide Message TX Hold Multiplier: Sets the hold multiplier value. The hold time multiplier is multiplied by the transmit interval to give the Time To Live (TTL) that the switch advertises to the neighbors. The range is from 2 to 10. Message TX Interval: Sets the transmit interval, which is the interval between regular transmissions of LLDP advertisements. The range is from 5 to 32768 seconds.
Web Smart Switch Series TRENDnet User’s Guide 4. At the bottom of the left hand panel, click Save. Dot1 TLVs Settings Network > LLDP > Dot1 TLVs Settings 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on LLDP, and click on Dot1 TLVs Settings. 3. Configure the Dot1 TLVs settings. Click Apply to save. 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK.
Web Smart Switch Series TRENDnet User’s Guide MED Port Settings Neighbor Network > LLDP > MED Port Settings Network > LLDP > Neighbor 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on LLDP, and click on MED Port Settings. 2. Click on Network, click on LLDP, and click on Neighbor. 3. Configure the MED port settings.
Web Smart Switch Series TRENDnet User’s Guide MAC VLAN Protocol VLAN MAC VLAN Protocol VLAN Profile Network > MAC VLAN Network > Protocol VLAN > Protocol VLAN Profile 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network and click on MAC VLAN. 2. Click on Network, click on Protocol VLAN, and click on Protocol VLAN Profile. 3.
TRENDnet User’s Guide Web Smart Switch Series Protocol VLAN Profile Interface Network > Protocol VLAN > Protocol VLAN Profile Interface 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Network, click on Protocol VLAN, and click on Protocol VLAN Profile Interface. 3. Configure the new Protocol Interface. Click Apply to save. Port – Select the port number from the dropdown. Profile ID– Select the profile ID from the drop down.
TRENDnet User’s Guide Web Smart Switch Series QoS (Quality of Service) When a port on an Ethernet switch becomes oversubscribed, its egress queues contain more packets than the port can handle in a timely manner. In this situation, the port may be forced to delay the transmission of some packets, resulting in the delay of packets reaching their destinations.
Web Smart Switch Series TRENDnet User’s Guide Port Priority DSCP Set Port Priority Set DSCP (Differentiated Services Code Point) Class Mapping settings QoS > Port Priority QoS > DSCP The Port Priority values are assigned to an untagged frame at ingress for internal processing in the switch. This procedure explains how to change the default mappings of port priorities to the User Priority. This is set at the switch level. You cannot set this at the per-port level.
Web Smart Switch Series TRENDnet User’s Guide 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK. Scheduling Algorithm Note: This step saves all configuration changes to the NV-RAM to ensure that if the switch is rebooted or power cycled, the configuration changes will still be applied. QoS > Scheduling Algorithm Set the Scheduling Algorithm 1. Log into your switch management page (see “Access your switch management page” on page 5). 2.
TRENDnet User’s Guide IPv6 Traffic Class Web Smart Switch Series 4. At the bottom of the left hand panel, click Save. Configure the IPv6 Traffic Class Settings QoS > IPv6 Traffic Class 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on QoS and click on IPv6 Traffic Class Priority Settings. 3. Review the settings. IPv6 Traffic Class Global Settings: Select Enable or Disable. Click Apply to save the settings.
Web Smart Switch Series TRENDnet User’s Guide Security This chapter contains information about the Port-based security features and the procedures for setting this feature. 2. Click on Security and click on Port Access Control. 3. Review the settings. Click Apply to save the settings. Configure the following parameters as required: NAS ID - This parameter assigns an 802.1x identifier to the switch that applies to all ports. The NAS ID can be up to sixteen characters.
TRENDnet User’s Guide Dial-in User Create Dial-In Users (Local Authentication Method) Security > Dial-in User Web Smart Switch Series In the list, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all of the entries in the table. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide Web Smart Switch Series RADIUS Add RADIUS Servers (RADIUS Authentication Method) In the list, you can click Modify to modify an entry or click Delete or delete the entry. Security > RADIUS 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security and click on RADIUS. 3. Review the settings. Server Priority – Enter the RADIUS Server priority (Highest: 1, Lowest: 5).
TRENDnet User’s Guide Web Smart Switch Series TACACS+ Add TACACS+ Servers (TACACS+ Authentication Method) Security > TACACS+ Terminal Access Controller Access Control System (TACACS+) provides centralized security user access validation. The system supports up-to 5 TACACS+ servers. TACACS+ provides a centralized user management system, while still retaining consistency with RADIUS and other authentication processes.
Web Smart Switch Series TRENDnet User’s Guide Destination MAC Filter 4. The MAC address will be added to the table. Destination MAC Filter Security > Destination MAC Filter This section contains an explanation of the Destination MAC Filter feature as well a procedure for configuring it. This section includes the following information: The Destination MAC Filter feature prevents the switch from forwarding packets to a specified device.
Web Smart Switch Series TRENDnet User’s Guide Denial of Service Denial of Service (DoS) 3. Next to the DoS item/rule you would like to activate, click the drop-down menu on the right hand side and select Deny. Security > Denial of Service The switch has built-in DoS prevention features to restrict specific type of traffic associated denial of service attacks on your network. By default, all of the DoS settings are set to Allow, which allow any type of traffic to pass through the switch.
Web Smart Switch Series TRENDnet User’s Guide o DHCP Snooping Settings DHCP Snooping > Settings Here is a summary of the rules to observe when you configure DHCP Snooping: A trusted port is connected to one of the following: o Directly to the legitimate trusted DHCP Server. o A network device relaying DHCP messages to and from a trusted server. o Another trusted source such as a switch with DHCP Snooping enabled.
Web Smart Switch Series TRENDnet User’s Guide 4. At the bottom of the left hand panel, click Save. VLAN Security > DHCP Snooping > VLAN In this section, you can define an existing VLAN to apply DHCP snooping. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security, click on DHCP Snooping, and click on VLAN. 5. Select the Config you would like to save the settings to, click Save Settings to Flash, then click OK.
Web Smart Switch Series TRENDnet User’s Guide 4. At the bottom of the left hand panel, click Save. Interfaces Security > DHCP Snooping > Interfaces This section allows you to set trusted port interfaces where DHCP servers can be connected allows or denies DHCP server information to be received on those ports. 1. Log into your switch management page (see “Access your switch management page” on page 5). 5.
Web Smart Switch Series TRENDnet User’s Guide Binding Security > DHCP Snooping > Binding The Binding Database displays learned and statically assigned MAC Address and IP Address information for each host on the local area network. Dynamically assigned IP addresses from the DHCP server will automatically populate the table on the Binding Database page as they are assigned by the server.
Web Smart Switch Series TRENDnet User’s Guide Dynamic ARP Inspection ARP Inspection Validation Settings Security > Dynamic ARP Inspection > ARP Inspection Validation Security > Dynamic ARP Inspection > ARP Access List 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security, click on Dynamic ARP Inspection, and click on ARP Access List. 2.
Web Smart Switch Series TRENDnet User’s Guide ARP Inspection Port Settings ARP Inspection VLAN Security > Dynamic ARP Inspection > ARP Inspection Port Settings Security > Dynamic ARP Inspection > ARP Inspection VLAN 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security, click on Dynamic ARP Inspection, and click on ARP Inspection Port Settings. 2.
Web Smart Switch Series TRENDnet User’s Guide ARP Inspection Statistics ARP Inspection VLAN Security > Dynamic ARP Inspection > ARP Inspection Statistics Security > Dynamic ARP Inspection > ARP Inspection VLAN 1. Log into your switch management page (see “Access your switch management page” on page 5). 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security, click on Dynamic ARP Inspection, and click on ARP Inspection Statistics 2.
Web Smart Switch Series TRENDnet User’s Guide ACL Access Control configuration allows you to control different aspects of the Ethernet traffic as it enters the switch ports and is process through the Switch. You can specify what traffic is permitted or denied to flow through the switch by setting up specific filter criteria at an ingress port. You can also manage the switching priority of Ethernet packets. All of this is done by specifying policies that define the filtering and priority behavior.
Web Smart Switch Series TRENDnet User’s Guide Access Profile List Security > ACL > Access Profile List The Access Profile List allows users to view the active ACL profiles. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security, click ACL, and click on Access Profile List. In the list, you can click Show Details to view the ACL Profile details, click Edit/New Rules to edit or create rule details, or delete the entry.
TRENDnet User’s Guide Web Smart Switch Series ACL Finder Security > ACL > ACL Finder 5. Modify existing ACL rules by editting established rule details. Allows you to view current policies assigned to each port by Index or Sequence. 1. Log into your switch management page (see “Access your switch management page” on page 5). 2. Click on Security, click on ACL, and click on ACL Finder. 3. The ACL Finder contains the following fields.
Web Smart Switch Series TRENDnet User’s Guide Tools Firmware Upgrade via HTTP Settings Firmware Upgrade 1. Log into your switch management page (see “Access your switch management page” on page 5). Tools > Firmware Upgrade Upgrade your switch’s firmware Tools > Firmware Upgrade 2. Click on Tools, click on Firmware Upgrade. TRENDnet may periodically release firmware upgrades that may add features or fix problems associated with your TRENDnet switch model and version.
Web Smart Switch Series TRENDnet User’s Guide Firmware Upgrade via TFTP Settings Config Backup Restore Tools > Firmware Upgrade Config Backup/Restore Note: Before using this method, you will require a TFTP server. There are third party TFTP server applications available for this function. If you are not familiar with the TFTP protocol, it is recommended to use the HTTP method. Tools > Configuration > Backup/Restore 1.
Web Smart Switch Series TRENDnet User’s Guide 3. Next to Select File, depending on your web browser, click on Browse or Choose File. Config File – Select the configuration. Startup-config refers to the configuration that was used to startup this switch. Config File Name: Enter the configuration file name for the backup. (Default: config.bin) 4. A separate file navigation window should open. 5. Select the switch configuration file to restore and click Restore. (Default Filename: config.bin).
Web Smart Switch Series TRENDnet User’s Guide Diagnostics The results will be displayed in the Cable Diagnostic Table below. Cable Diagnostics Test Tools > Diagnostics The switch provides a basic cable diagnostic tool in the GUI for verifying the pairs in copper cabling and estimated distance for troubleshooting purposes. Note: 1. If the cable length displays N/A, it means that the cable length is Not Available. The may be due to the port being unable to determine the estimated cable length.
Web Smart Switch Series TRENDnet User’s Guide Reboot To reset your switch to factory defaults: Reboot/Reset to factory defaults You may want to reset your switch to factory defaults if you are encountering difficulties with your switch and have attempted all other troubleshooting. Before you reset your switch to defaults, if possible, you should backup your switch configuration first, see “Backup/Restore” on page 88.
TRENDnet User’s Guide Web Smart Switch Series Ping Network Connectivity Test (Ping Tool) Tools > Ping This chapter provides the procedure to ping a node on your network from the switch. This procedure is useful in determining whether an active link exists between the switch and another network device. The device you are pinging must be a member of the Default VLAN and within the same local area network as your switch.
TRENDnet User’s Guide Web Smart Switch Series Using the Web Smart Switch Management Utility The Web Smart Management Utility allows you to do the following: You can easily discover all TRENDnet web smart switches on your network using the discover feature. You can modify the IP address settings, change the admin password, and upgrade firmware for multiple switches.
Web Smart Switch Series TRENDnet User’s Guide 5. At the Installation, click Install. Using the Utility Launching the Utility Upon completing the software installation, a desktop shortcut is automatically created. Double-click the icon to start the utility or open the utility if it is already running. Closing the utility will exit the application. You can also click Exit at the bottom of the utility user interface to exit the application. 6. In the Completion window, click Finish.
Web Smart Switch Series TRENDnet User’s Guide Discovery List Monitor List This is the list where you can discover all the Web management devices in your network. All the Web Smart switches in the Monitor List can be monitored; you can also receive the trap and show the status of the device. By pressing the “Discovery” button, you can list all the Web Smart Management switches in the discovery list.
TRENDnet User’s Guide Device Setting Web Smart Switch Series Firmware Upgrade: When the device has a new function, there will be a new firmware to update the device, use this function to update. You can set the device by using the function key in the Device Setting Dialog box. Configuration Setting: In this Configuration Setting, you can set the IP Address, Subnet Mask, Gateway, Group Interval, System name, Location and IP Mode.
TRENDnet User’s Guide Web Smart Switch Series Main Menu Options In the “File TAB”, there are Monitor Save, Monitor Save As, Monitor Load and Exit. Monitor Save: To record the setting of the Monitor List to the default, when you open the Web Management Utility next time, it will auto load the default recorded setting. Monitor Save As: To record the setting of the Monitor List in appointed filename and file path. Monitor Load: To manually load the setting file of the Monitor List.
Web Smart Switch Series TRENDnet User’s Guide Hardware Features and Specifications TEG-082WS (2.0R) TEG-204WS (1.0R) TEG-284WS (1.0R) TEG-524WS (1.
Web Smart Switch Series TRENDnet User’s Guide TEG-082WS (2.0R) TEG-204WS (1.0R) TEG-284WS (1.0R) Operating Temperature -5° – 50°C (23° - 122°F) Operating Humidity Max. 95% non-condensing Dimensions 280 x 125.8 x 44 mm (11 x 5 x 1.74 in.) TEG-524WS (1.0R) 280 x 180 x 44 mm 440 x 140 x 44mm 440 x 210 x 44mm (11 x 7 x 1.74 in.) (17.4 x 5.51 x 1.74 in.) (17.3 x 8.3 x 1.74 in.) Rack mountable 1U height Weight 0.98 kg (2.2 lbs.) 1.76 kg (3.88 lbs.) 2.15 kg (4.73 lbs.) 3.48 kg (7.67 lbs.
Web Smart Switch Series TRENDnet User’s Guide Web Smart Switch Series Software & Technical Specifications IEEE 802.1d IEEE 802.1p IEEE 802.1Q IEEE 802.1s IEEE 802.1w CLI (Telnet / SSHv2) for basic administration HTTP/HTTPS (SSL v2/3 TLS) Web based GUI SNMP v1, v2c, v3 RMON v1 IP Forward Table MIB RFC 1354 RMON MIB RFC 1271 IPv4 MIB RFC 1213 IPv6 MIB RFC 2465 GVRP MIB IEEE 802.1Q-VLAN LA MIB IEEE 802.3ad LLDP MIB IEEE 802.
Web Smart Switch Series TRENDnet User’s Guide Multicast IGMP Snooping v1, v2, v3 MLD Snooping v1, v2 IGMP fast leave MVR (Multicast VLAN Registration) Port Mirror RX, TX, or Both Many to one 802.
TRENDnet User’s Guide Quick Installation GuideTroubleshooting Q: I typed http://192.168.10.200 in my Internet Browser Address Bar, but an error message says “The page cannot be displayed.” How can I access the switch management page? Answer: 1. Check your hardware settings again. See “Switch Installation” on page 8. 2. Make sure the Power and port Link/Activity and WLAN lights are lit. 3.
Web Smart Switch Series TRENDnet User’s Guide Appendix Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance.
Web Smart Switch Series TRENDnet User’s Guide In MAC OS 10.4, from the Show drop-down list, select Built-in Ethernet and select the TCP/IP tab. In MAC OS 10.5/10.6, in the left column, select Ethernet. e. Configure TCP/IP to use a static IP. In MAC 10.4, from the Configure IPv4, drop-down list, select Manually and assign your network adapter a static IP address. Then click the Apply Now button. In MAC 10.5/10.
Web Smart Switch Series TRENDnet User’s Guide Federal Communication Commission Interference Statement RoHS This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received; including interference that may cause undesired operation. This product is RoHS compliant.
Limited Warranty TRENDnet User’s Guide Limited Warranty TRENDnet warrants only to the original purchaser of this product from a TRENDnet In the event that, after evaluation, TRENDnet cannot replace the defective product or there is no comparable model available, we will refund the depreciated value of the product. authorized reseller or distributor that this product will be free from defects in material and workmanship under normal use and service.
Limited Warranty TRENDnet User’s Guide shipping from outside of the USA and Canada are responsible for any return shipping CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, and/or customs charges, including but not limited to, duty, tax, and other fees.
