TRENDnet User’s Guide Contents PRODUCT OVERVIEW .......................................................................................................2 FEATURES............................................................................................................................................ 2 FRONT VIEW ....................................................................................................................................... 3 LED INDICATORS ...........................................
TRENDnet User’s Guide TEG-082WS Hardware Design Product Overview Provides 8 x Gigabit ports, 2 x shared SFP slots, a 16 Gbps switching capacity, a built-in power supply, and rackmount brackets Fanless Fanless design reduces energy consumption and operating noise IPv6 Ready This switch supports IPv6 configuration and IPv6 neighbor discovery Traffic Management A broad range of network configurations are supported by: 802.3ad link aggregation, Asymmetric VLAN, 802.
TRENDnet User’s Guide TEG-082WS Front View Reset Button LED Indicators LED Indicators GbE Network Ports Interfaces Reset Button Gigabit Ethernet Ports (1-8) SFP slots (7F, 8F) Power (PWR) LED On The TEG-082WS is powered on. Off The TEG-082WS is not powered. SFP Share Port Link/ACT LED (per port) On The respective port is successfully connected to an Ethernet network. Blinking The port is transmitting or receiving data on the Ethernet network. Off No link.
TRENDnet User’s Guide Speed LED (per port) Green When respective LED shows in solid green LED, the port is connected to a 1000Mbps Gigabit Ethernet network. Amber When respective LED shows in solid amber, the port is connected to a 100Mbps Ethernet network. Off When the LINK LED is on and Speed LED is off, the respective port is connected to a 10Mbps Ethernet network. TEG-082WS Shared SFP Slots (7F, 8F) Solid The port is inserted mini-GBIC Gigabit module and gigabit link Green is established.
TRENDnet User’s Guide Rear View TEG-082WS Switch Installation Desktop Hardware Installation The site where you install the switch stack may greatly affect its performance. When installing, consider the following pointers: Note: The model showing in illustrations may be different to the one you have. AC Power Connector – Connect the AC power cord to the connector and the other side into a power outlet.
TRENDnet User’s Guide TEG-082WS Rack Mount Hardware Installation Basic Installation The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipment. Attach the mounting brackets at the switch’s front panel (one on each side), and secure them with the provided screws. 1. Power on your TEG-082WS and connect your computer to the switch. Note: The switch model may be different than the one shown in the example illustrations. 2.
TRENDnet User’s Guide 3. Open your web browser, and enter the IP address of the switch, and then press Enter. The default IP address is 192.168.10.200. TEG-082WS 6. Configure the switch IP address settings to be within your network subnet, then click Apply. Note: You may need to modify the static IP address settings of your computer’s network adapter to IP address settings within your subnet in order to regain access to the switch. 4. Enter the User Name and Password, and then click Login.
TRENDnet User’s Guide TEG-082WS Connect additional devices to your switch You can connect additional computers or other network devices to your switch using Ethernet cables to connect them to one of the available Gigabit Ethernet Ports (1-8). Check the status of the LED indicators on the front panel of your switch to ensure the physical cable connection from your computer or device.
TRENDnet User’s Guide TEG-082WS Configure your switch Switch Info Access your switch management page You’ll landing on Switch Info page when login to the web management GUI. You can view your switch status information here. Note: Your switch default management IP address http://192.168.10.200. You can manage the TEG-082WS websmart switch using Internet web browser on your choice. (e.g. Internet Explorer®, Firefox®, Chrome™, Safari®, or Opera™). 1.
TRENDnet User’s Guide Switch Information System Up For: The duration your switch has been running continuously without a restart/power cycle (hard or soft reboot) or reset. Runtime Image: The current software or firmware version your switch is running. Boot Loader: The current boot loader version your switch is running. Hardware Information DRAM Size: Displays your switch RAM memory size. Flash Size: Displays your switch Flash memory size.
TRENDnet User’s Guide TEG-082WS System System Management System > System Management This section explains how to assign a name, location, and contact information for the switch. This information helps in identifying each specific switch among other switches in the same local area network. Entering this information is optional.
TRENDnet User’s Guide TEG-082WS Set your IPv4 settings Click Apply to apply the change to the switch System > IPv4 Setup This section allows you to change your switch IPv4 address settings. Typically, the IP address settings should be changed to match your existing network subnet in order to access the switch management page on your network. Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent.
TRENDnet User’s Guide Set your IPv6 settings System > IPv6 System Settings Use the IPv6 System Settings page to configure the IPv6 network interface, which is the logical interface used for in-band connectivity with the switch via all of the switch's front-panel ports. The configuration parameters associated with the switch's network interface do not affect the configuration of the front-panel ports through which traffic is switched or routed.
TRENDnet User’s Guide A link-local address is an IPv6 unicast address that can be automatically configured on any interface using the link-local prefix FE80/10 and the interface identifier in the modified EUI-64 format. Link-local addresses are used in the neighbor discovery protocol and the stateless auto configuration process. Nodes on a local link can use link-local addresses to communicate; the nodes do not need globally unique addresses to communicate.
TRENDnet User’s Guide TEG-082WS Add IPv6 neighbors Restrict access to switch management page System > IPv6 Neighbor Settings These settings allows you to manually define IPv6 supported neighboring devices on your network. System > IP Access List This section allows you to define or restrict access to the switch management page to a list of specific IP addresses. IPv6 Neighbor Settings Neighbor IPv6 Specifies the neighbor IPv6 address. Address: Link Layer MAC Specifies the link layer MAC address.
TRENDnet User’s Guide IP Access List Table For each entry, the access list will populate. You can click Delete next to the entry to delete the entry or Delete All to delete all entries in the table. When you have completed entering the IPv4 and IPv6 address entries, click the IP Restriction Status drop-down list at the top and select Enabled, then click Apply.
TRENDnet User’s Guide Changing the administrator password In the Password field, enter the new password and enter the new password again the Confirm Password field to verify. Then, click Apply. TEG-082WS Enable or disable SNMP and modify idle timeout settings System > User Interface This section explains how to enable SNMP on the switch and modify the switch management page idle timeout settings. Note: If you disable the SNMP on the switch, the switch will not be manageable via SNMP using MIBs.
TRENDnet User’s Guide Timeout Settings Web Idle Timeout: Enter the idle period in minutes, when the switch will automatically log out an idled user from the switch management page. Default: 10 min. Group Interval: The IGMP group timeout interval. Default: 120 sec. TEG-082WS Set the switch date and time System > System Time Click Apply to apply the change to the switch Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. © Copyright 2014 TRENDnet.
TRENDnet User’s Guide Current Time Settings Clock Mode: Displays if system time and date is set manually Local Time or obtained automatically from a network time server SNTP. Current Time: Displays the current system time and date. Time Zone: Displays the current system time zone. TEG-082WS SNTP Poll Enter the interval time when your switch will update Interval: the time and date settings with the time server. Default: 1 min. Time Zone Click the drop-down list to select your time zone.
TRENDnet User’s Guide TEG-082WS Enable HTTPS/SSL (Secure Socket Layer) management access Click Apply to apply the change to the switch System > SSL Settings By default, your switch management page can be accessed using standard web HTTP protocol which transmit files with clear text over the network. Enabling HTTPS/SSL management access allows access to the switch management page using encrypted communication prevents your data been eavesdropped by unauthorized user.
TRENDnet User’s Guide TEG-082WS Enable DHCP Auto Configuration View and setup your switch logging System > DHCP Auto Configuration If you need to synchronize the switch configuration file on remote server, the DHCP Auto Configuration feature is available for this purpose via the DHCP server. Your IP address settings must enabled to the DHCP client so that this feature can operate with your DHCP/TFTP server.
TRENDnet User’s Guide System Log Settings Time Stamp: Enable/Disable the time stamp on log entry. Default: Enabled. Message Enter the message buffer size. Default: 50 entries, Buffered Size: Range: 1-200. Syslog Status: Enable/ Disable to store the logs on remote log server. Default: Enabled. TEG-082WS Physical Interface This section allows you to configure the physical port parameters such as speed, duplex, flow control, and jumbo frames.
TRENDnet User’s Guide Physical Interface Table Port: Specifies the port number. The All value indicates ports 1 through 8 on the Switch. The port number 7 and 8 are Gigabit and SFP shared ports. Only one interface will be activated at the same time. When SFP and Gigabit connection coexist, the SFP will take the priority. (1) Gigabit Port (2) SFP with 100FX module (3) SFP with 1000X module Trunk: This cell displays the trunk status with trunk group number.
TRENDnet User’s Guide o o o o 10/Full -This parameter indicates the port is configured for 10Mbps operation in full-duplex mode. 1000/Half -This parameter indicates the port is configured for 1000Mbps operation in half-duplex mode. 100/Half -This parameter indicates the port is configured for 100Mbps operation in half-duplex mode. 10/Half -This parameter indicates the port is configured for 10Mbps operation in half-duplex mode.
TRENDnet User’s Guide EAP: This number shows the current Extensible Authentication Protocol (EAP) setting on the port. All Ports: If you select Ignore and click on Apply for all ports, the EAP setting is not changing. If you select Enabled or Disabled then click on Apply for all ports, EAP setting on all ports will be set to the same value on Enabled or Disabled. TEG-082WS Note: Click Apply in the end of the row to apply the change.
TRENDnet User’s Guide TEG-082WS Bridge The Bridge session covers most of the web smart switch features including spanning tree, trunk configuration, IGMP snooping, bandwidth control, VLAN, VGRP, and QoS. Spanning Tree (STP, RSTP, MSTP) Configure Spanning Tree Protocol settings Bridge > Spanning Tree > Protocol Settings Spanning Tree Protocol (STP) provides network topology for any arrangement of bridges/switches. STP also provides a single path between end stations on a network, eliminating loops.
TRENDnet User’s Guide Bridge Priority: The Bridge Priority has a range 0 to 61440 in increments of 4096. To make this easier for you, the Web Management Utility divides the range into increments. You specify the increment that represents the desired bridge priority value. Maximum Age: The Maximum Age defines the amount of time a port will wait for STP/RSTP information. MSTP uses this parameter when interacting with STP/RSTP domains on the boundary ports.
TRENDnet User’s Guide TEG-082WS Note: Click Apply in the end of the row to apply the change. BPDU pass-through must be disabled for all ports under Physical interface for STP can be enabled. Priority: Indicates the port priority. If two paths have the same port cost, the bridges must select a preferred path. In some instances this can involve the use of the port priority parameter which is used as a tie breaker when two paths have the same cost. The range for port priority is 0 to 240.
TRENDnet User’s Guide automatically. The default setting for this parameter is Auto. Note: Click Apply in the end of the row to apply the change. If you select Ignore on All Ports and click on Apply for all ports, the Admin Cost setting is not changing. If you set the value then click on Apply for all ports, The Admin Cost will be set to the same value. P2P: Choosing the Forcetrue parameter indicates a pointto-point (P2P) shared link.
TRENDnet User’s Guide Configure Spanning Tree Protocol MST settings (MSTP) Bridge > Spanning Tree > MST Settings TEG-082WS MST Instance Settings MSTI ID: Displays the MSTI ID associated with the VLAN ID. Range: 1 to 31. VID List: Displays the VLAN ID associated with MSTI. Click Add to add the VLAN and MSTI association on MST table. Range: 0 to 4094. Priority: Select a priority in the Priority field. The user may set a priority value between 0 and 61440.
TRENDnet User’s Guide TEG-082WS View your Spanning Tree Protocol Instance Information (MSTP) Configure Spanning Tree Protocol MST Port Settings (MSTP) Bridge > Spanning Tree > Instance Information Bridge > Spanning Tree > MST Settings MST Port Settings Select MST Port: Click the drop-down to select which MST port to configure. Instance Information MSTI ID: Specifies the ID of MSTI. Internal Root Root cost to the root bridge Cost: Root Port: Root port of the specific instance.
TRENDnet User’s Guide Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. TEG-082WS Trunk Configuration (Link Aggregation) Configure port trunk settings Bridge > Trunk Config > Trunking The trunking function enables the cascading of two or more ports for a combined larger total bandwidth. Up to 4 trunk groups may be created, each supporting up to 8 ports.
TRENDnet User’s Guide TEG-082WS For each Trunk ID/Group, check the port numbers to add for each trunk group. View your trunk group status information Click the drop-down list and select one of the following options. Bridge > Trunk Config > LACP Group Status Active: The specific aggregator will broadcast and respond to LACPDU (LACP Data Unit) packets. This setting enables the dynamic LACP feature for the trunk.
TRENDnet User’s Guide TEG-082WS Configure your port priority Click Apply to apply the change to the switch Bridge > Trunk Config > Port Priority Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. Port Priority Status System Priority: Preassigned setting that cannot be modified. This value applies to the switch. System ID: MAC address value assigned to the individual switch. This value cannot be modified.
TRENDnet User’s Guide Mirroring Configure port mirror settings Bridge > Mirroring Port mirroring allows you to monitor the ingress and egress traffic on a port by having the traffic copied to another port where a computer or device can be set up to capture the data for monitoring and troubleshooting purposes. TEG-082WS Disabled: This parameter de-activates the Port Mirroring feature and the rest of the configuration parameters become inactive on the page.
TRENDnet User’s Guide Loopback Detection Enable loopback detection Bridge > Loopback Detection The loopback detection feature allows the switch to detect and prevent disruption from loops that occur on uplink or downlink switches directly connected to your switch. TEG-082WS Loopback Detection Settings State: Select Enabled to enable the loopback detection feature. Select Disabled to disabled the loopback detection feature.
TRENDnet User’s Guide Loop Status: Display the current loopback status. Action: Next to each entry, click Apply to apply the change of the port. TEG-082WS Static Unicast Add static unicast entries to the switch Bridge > Static Unicast Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. Static Unicast Address Settings 802.1Q VLAN: Enter the VLAN ID where the MAC address will reside.
TRENDnet User’s Guide 802.1Q VLAN On the list, you can click Modify to modify an entry or click Delete to delete the entry. You can also click Delete All to delete all the entries in the list. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide 802.1Q VLAN On the list, you can click Modify to modify an entry or click Delete to delete the entry. You can also click Delete All to delete all the entries in the list. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide Query Interval: Enter the amount of time you want your switch to send IGMP queries. Max Response When a host receives the query packet, it starts Time: counting to a random value, less than the maximum response time. When this timer expires, host replies with a report, provided that no other host has responded yet. Robustness Adjust the robustness variable to compensate the Variable: packet loss.
TRENDnet User’s Guide TEG-082WS Bandwidth Control Configure Storm Control Bridge > Bandwidth Control > Storm Control This section allows you to configure the DLF (Destination Lookup Failure), broadcast, and multicast storm settings for each switch port. Check the static router ports to add and click Apply to save the settings. Note: You can click on All to add all ports. Clicking Restore will restore the static router port settings to default.
TRENDnet User’s Guide Multicast: Click the drop-down list and select Enabled to enable multicast storm control. Threshold: Enter the pps (packets per second) threshold. Action: Modifying settings in the row marked All, will apply the settings to all ports. Click Apply to apply the change. TEG-082WS Set Ingress Rate Limiting Bridge > Bandwidth Control > Ingress Rate Limiting This section allows you to set the ingress (receive) rate for each switch port.
TRENDnet User’s Guide Set Egress Rate Limiting Bridge > Bandwidth Control > Egress Rate Limiting This section allows you to set the egress (transmit) rate for each switch port. TEG-082WS VLAN Add, modify, and remove VLANs Bridge > VLAN > Tagged VLAN A VLAN is a group of ports that can be anywhere in the network, but communicate as though they were in the same area. Egress Rate Limiting Settings Port: The port number. Bandwidth Enter the egress rate limit value.
TRENDnet User’s Guide VLANs can be easily organized to reflect department groups (such as R&D, Marketing), usage groups (such as e-mail), or multicast groups (multimedia applications such as video conferencing), and therefore help to simplify network management by allowing users to move devices to a new VLAN without having to change any physical connections. Tagged VLAN Settings VLAN ID: Enter the VLAN ID for the new VLAN. VLAN Name: Enter the VLAN name.
TRENDnet User’s Guide Configure VLAN Port Settings Bridge > VLAN > Port Settings In this section, you can modify the port VID settings, acceptable frame types, and ingress filtering. TEG-082WS Untagged & Priority Tagged: The port can accept untagged frames and frames with tagged priority information only such as 802.1p. Ingress Filtering: Click the drop-down list and select Enabled to enable ingress filtering or Disabled to disable ingress filtering.
TRENDnet User’s Guide TEG-082WS Configure the VLAN Forwarding Table Mode Bridge > VLAN > Forwarding Table Mode This section allows you to configure your switch to standard 802.1Q VLAN mode (IVL) or Asymmetric VLAN mode (SVL). Asymmetric VLAN allows the configuration of overlapping untagged VLAN ports in order to create VLAN groups. It is recommended to use the standard 802.1Q VLAN mode when possible.
TRENDnet User’s Guide TEG-082WS View the switch VLAN dynamic forwarding table Create a private VLAN Bridge > VLAN > Dynamic Forwarding Table This section allows you to view the VLAN forwarding table with dynamically generated forwarding table entries as devices more devices are connected to your switch. Bridge > VLAN > Private VLAN The private VLAN feature allows you to create a more secure VLAN that is completely isolated to its members and cannot communicate with other VLANs.
TRENDnet User’s Guide TEG-082WS Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. To configure Private VLAN Settings, perform the following procedure: Change the Private VLAN Settings by clicking the State radio button choices that you want to change. o Enable: Enable Private VLAN settings. o Disable: Disable Private VLAN settings. Press Apply to make the changes to take effect. Set the Source Port to on port 1 – 8.
TRENDnet User’s Guide View the current VLAN database Bridge > VLAN > VLAN Database TEG-082WS GVRP (GARP VLAN Registration Protocol) The GARP VLAN Registration Protocol (GVRP) allows network devices to share VLAN information and to use the information to modify existing VLANs or create new VLANs, automatically. This makes it easier to manage VLANs that span more than one switch.
TRENDnet User’s Guide Set GVRP port settings Bridge > GVRP > Port Settings This section will allow you to select which ports will have GVRP enabled or will be restricted from using GVRP. TEG-082WS Enabled: The Dynamic Vlan is activated for the port row selected. Disabled: The Dynamic VLAN is de-active for the respective port. Restricted VLAN This parameter controls if the VLAN registration on the Registration port is restricted or not.
TRENDnet User’s Guide Set GVRP time settings Bridge > GVRP > Time Settings This section will allow you to define the GARP Join, Leave, and Leave All Time for each port. TEG-082WS LeaveTime: This parameter is the GARP Leave Timer. Its range is 30 - 2147483630 milli-seconds. This timer must be set in relation to the GVRP Join Timer according to the following equation: GARPLeaveTimer >= (GARPJoinTimer X 2) + 10 LeaveAllTime: This parameter is the GARP Leave Timer. Its range is 30 - 2147483630 milli-seconds.
TRENDnet User’s Guide QoS (Quality of Service) When a port on an Ethernet switch becomes oversubscribed, its egress queues contain more packets than the port can handle in a timely manner. In this situation, the port may be forced to delay the transmission of some packets, resulting in the delay of packets reaching their destinations.
TRENDnet User’s Guide TEG-082WS Set Port Priority Set DSCP (Differentiated Services Code Point) Class Mapping settings Bridge > QoS > Port Priority The Port Priority values are assigned to an untagged frame at ingress for internal processing in the switch. This procedure explains how to change the default mappings of port priorities to the User Priority. This is set at the switch level. You cannot set this at the per-port level. To change the port priority mappings, perform the following procedure.
TRENDnet User’s Guide For each DSCP In value that is relevant to your configuration, select a queue (Low, Medium, High, or Highest) in the Queue column. Select Enabled in the DSCP Mapping drop-down list. Click Apply to save the settings. TEG-082WS Set the Scheduling Algorithm Bridge > QoS > Scheduling Algorithm Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. Select your scheduling algorithm and then click Apply to save the settings.
TRENDnet User’s Guide Configure the IPv6 Traffic Class Priority Settings Bridge > QoS > IPv6 Traffic Class Priority Settings TEG-082WS On the IPv6Traffic Class Table, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all of the entries in the table. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide TEG-082WS SNMP Set the SNMP Engine ID You can manage a switch by viewing and configuring the management information base (MIB) objects on the device with the Simple Network Management Program (SNMP). This chapter describes how to configure SNMP. A Group Name, IP address of the switch and at least one community string is the minimum required to manage the switch using SNMP.
TRENDnet User’s Guide Configure the SNMP View Table SNMP > View Table The SNMP View table specifies the MIB object access criteria for each View Name. If the View Name is not specified on this page, then it has access to all MIB objects. You can specify specific areas of the MIB that can be accessed or denied based on the entries in this table. You can create and delete entries in the View table. TEG-082WS Enter the View Type. Choose from the following options, and then click Add.
TRENDnet User’s Guide TEG-082WS Configure the SNMP Group Access Table To create SNMP View Names: SNMP > Group Access Table The SNMP View Names are defined in the SNMP Group Access Table and are based on the User and Group Names. Before you can create an SNMP View name, you must define a Group Name using the SNMP User/Group page. © Copyright 2014 TRENDnet. All Rights Reserved. Enter the Group Name. This entry must be pre-defined on the SNMP User/Group page. Enter the Read View Name.
TRENDnet User’s Guide TEG-082WS To modify a SNMP View Name: Configure the SNMP User/Group Table If you need to modify an entry in the SNMP Group Access page, you must first delete the entry and then re-enter it. SNMP > SNMP User/Group An SNMP User Name and Group Name definition is the basis for all the other SNMP tables.
TRENDnet User’s Guide To create a SNMP User and Group Name: Note: There are no default User Name or Group Name defined for SNMP. Type a new User Name. Enter a name up to 31 characters in length. Type a new Group Name. Enter a name up to 31 characters in length. From the SNMP Version pull down menu, select v3. The encryption check-box becomes active. Check the encryption check-box. The Auth-Protocol, Priv-Protocol, and associated password fields become active.
TRENDnet User’s Guide Configure the SNMP Community Table SNMP > Community Table A community string has attributes for controlling who can use the string and what the string will allow a network management station to do on the switch. The Web Management Utility does not provide any default community strings. You must first define an SNMP User and Group Name on the SNMP User/Group page and then define a Community Name on the SNMP Community Table page.
TRENDnet User’s Guide TEG-082WS Configure the SNMP Trap Management To create a Trap Host Table Entry: SNMP > Trap Management A Host IP address is used to specify a management device that needs to receive SNMP traps sent by the switch. This IP address is associated with the SNMP Version and a valid Community Name in the Host table of the switch.
TRENDnet User’s Guide To delete a Trap Host Table Entry: To delete an entry in the host table, click Delete next to the entry in the table that you want to remove. The Host table entry is removed from the table. No confirmation message is displayed. Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. © Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide Configure Policy Settings Access Control Config > Policy Settings The Policy Settings page allows you to specify the filtering criteria for one policy.
TRENDnet User’s Guide o o o o o DSCP: The DSCP (Differentiated Services Code Point) value in the IP header ranging from 0 to 63. Source Layer 4 Port: Indicates the source layer 4 port ranging from 1 to 65535. Destination Layer 4 Port: Indicates the destination layer 4 port ranging from 1 - 65535. Policy Sequence: Enter a number in the Policy Sequence field. The Policy Sequence must be a unique number within the range of 1 - 65535. This field is mandatory.
TRENDnet User’s Guide TEG-082WS Add IPv6 To add an IPv6 policy, use the following procedure: Click Add IPv6, The Policy Settings page. Enter a number in the Policy Index field. The policy index is a unique number within the range of 1 – 65535 which identifies the policy. This field is mandatory. Choose the parameters to add for the policy, and enter data one or more of the parameters required for your policy.
TRENDnet User’s Guide If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages. Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. TEG-082WS Configure Rate Control Access Control Config > Rate Control The Policy Settings page allows you to specify the filtering criteria for one policy.
TRENDnet User’s Guide On the list, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all of the entries in the table. If the entries span multiple pages, you can navigate page number in the Page field and click Go or you can click First, Previous, Next, and Last Page to navigate the pages.
TRENDnet User’s Guide TEG-082WS RMON Enable RMON The RMON (Remote MONitoring) MIB is used with SNMP applications to monitor the operations of network devices. The Switch supports the four RMON MIB groups listed here: RMON > Global Settings This section allows you to enable or disable RMON functionality. Statistic group: This group is used to view port statistics remotely with SNMP programs.
TRENDnet User’s Guide TEG-082WS Configure parameters for RMON Ethernet statistics Click Add to add the entry to the table. RMON > Statistics You can remotely view individual port statistics with RMON by using your SNMP NMS software and the RMON portion of the MIB tree. On the list, you can click Modify to modify an entry or click Delete or delete the entry. You can also click Delete All to delete all of the entries in the table.
TRENDnet User’s Guide Configure parameters for RMON history control settings RMON > History RMON histories are snapshots of port statistics. They are taken by the switch at predefined intervals and can be used to identify trends or patterns in the numbers or types of ingress packets on the ports on the switch. The snapshots can be viewed with your SNMP NMS software with the history group of the RMON portion of the MIB tree. A history group is divided into buckets.
TRENDnet User’s Guide TEG-082WS with more than one alarm, you probably will not create more than three events. Configure parameters for RMON alarms RMON > Alarm RMON alarms are used to generate alert messages when packet activity on designated ports rises above or falls below specified threshold values. The alert messages can take the form of messages that are entered in the event log on the switch or traps that are sent to your SNMP NMS software or both. • Alarm: The last component is the alarm itself.
TRENDnet User’s Guide RMON Alarm Settings Index: This parameter specifies the ID number of the new group. The range is 1 to 65535. Interval: This parameter specifies the time (in seconds) over which the data is sampled. Its range is 1 to 2147483647 seconds. Variable: This parameter specifies the RMON MIB object that the event is monitoring. Sample type: This parameter defines the type of change that has to occur to trigger the alarm on the monitored statistic.
TRENDnet User’s Guide Configure parameters for RMON events RMON > Event An event specifies the action of the switch when the ingress packet activity on a port crosses a statistical threshold defined in an alarm. The choices are to log a message in the event log of the switch, send an SNMP trap to an SNMP workstation, or both.
TRENDnet User’s Guide Voice VLAN This chapter contains a description of the Switch’s Voice VLAN feature and the procedures to create, modify, and delete a voice VLAN configuration. The Voice VLAN feature is specifically designed to maintain high quality, uninterrupted voice traffic through the switch. When talking on a voice over IP phone, a user expects to have no interruptions in the conversation and excellent voice quality. The Voice VLAN feature can be configured to meet these requirements.
TRENDnet User’s Guide a predefined OUI in the source MAC address. The port will leave the voice VLAN after a specified timeout period. This port behavior is configured with the voice VLAN Auto-Detection feature. For the Auto-Detection feature to function, your IP phone(s) must be capable of generating 802.1Q packets with imbedded VLAN ID tags. You must manually configure your IP phone(s) for the same VLAN ID as the switch’s voice VLAN ID.
TRENDnet User’s Guide Use the following procedure to configure voice VLAN: • From the Voice VLAN field at the top of the page, select one of the following radio button choices: o o • Enable: The voice VLAN feature is active. The other parameter fields in the Voice VLAN Global Settings section become active and are eligible for data to be entered. Disable: The voice VLAN feature is inactive.
TRENDnet User’s Guide TEG-082WS Configure Voice VLAN OUI settings Voice VLAN > Voice VLAN OUI Settings Modify OUI Setting To modify or delete an OUI, it must be first be deleted and then re-created. Delete OUI Setting To delete a specific OUI that had already been entered in the table at the bottom of the page, click on Delete in the Action column of the table. The specific OUI will be deleted from the table.
TRENDnet User’s Guide TEG-082WS Security Configure Port Access Control This chapter contains information about the Port-based security features and the procedures for setting this feature. Security > Port Access Control This section contains information and configuration procedures for the Port-based Access Control. Port-based Network Access Control (IEEE 802.1x) is used to control who can send traffic through and receive traffic from a switch port.
TRENDnet User’s Guide TEG-082WS • Authentication Method: This parameter indicates the authentication method used by the switch. Select one of the following choices: o o o RADIUS: This parameter configures port security for remote authentication. After completing steps, you must configure the “RADIUS Client” section. Local: This parameter configures port security for local authentication. After completing steps, you must configure the parameters for “Dial-in User— Local Authentication” section.
TRENDnet User’s Guide Create Dial-In Users (Local Authentication Method) Security > Dial-in User Dial-in User feature provides the local authentication server for port security when a remote (RADIUS) server is not available. The Dial-in User (local) authentication method allows you to set up 802.1x authentication parameters internally in the Switch. In this case, the user name and password combinations are entered with an optional VLAN when they are defined.
TRENDnet User’s Guide TEG-082WS Add RADIUS Servers (RADIUS Authentication Method) Click Add to add the entry to the table. Security > RADIUS In the list, you can click Modify to modify an entry or click Delete or delete the entry. Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent. . RADIUS Settings Server Priority: Enter the RADIUS Server priority (Highest: 1, Lowest: 5).
TRENDnet User’s Guide Add TACACS+ Servers (TACACS+ Authentication Method) Security > TACACS+ Terminal Access Controller Access Control System (TACACS+) provides centralized security user access validation. The system supports up-to 5 TACACS+ servers. TACACS+ provides a centralized user management system, while still retaining consistency with RADIUS and other authentication processes. The TACACS+ protocol ensures network integrity through encrypted protocol exchanges between the client and TACACS+ server.
TRENDnet User’s Guide TEG-082WS Destination MAC Filter Security > Destination MAC Filter This section contains an explanation of the Destination MAC Filter feature as well a procedure for configuring it. This section includes the following information: The Destination MAC Filter feature prevents the switch from forwarding packets to a specified device. On the Destination MAC Filter Page of the Web Management Utility software, enter the MAC address of the device that you want to filter.
TRENDnet User’s Guide Denial of Service (DoS) Security > Denial of Service The switch has built-in DoS prevention features to restrict specific type of traffic associated denial of service attacks on your network. By default, all of the DoS settings are set to Allow, which allow any type of traffic to pass through the switch. Setting one of the items to Deny will set the switch to check for traffic matching the selected item and deny any traffic matching the rule.
TRENDnet User’s Guide TEG-082WS DHCP Snooping Enable DHCP Snooping Here is a summary of the rules to observe when you configure DHCP Snooping: DHCP Snooping > General Settings • A trusted port is connected to one of the following: o o o o Directly to the legitimate trusted DHCP Server. A network device relaying DHCP messages to and from a trusted server. Another trusted source such as a switch with DHCP Snooping enabled.
TRENDnet User’s Guide Verify MAC Select one of the following choices from the pull-down Address: menu: Enabled: The MAC address of each ingress ARP packet is validated when compared against the Binding Table entries. Invalid ARP packets are discarded. Disabled: The MAC address of each ingress ARP packet is not validated against the Binding Table. All ARP packets are forwarded through the switch without regard to the IP and MAC Address information in the packet header.
TRENDnet User’s Guide TEG-082WS Set Trusted Interfaces Note: You can select the row labeled ALL to apply settings to all ports. DHCP Snooping > Trusted Interfaces This section allows you to set trusted port interfaces where DHCP servers can be connected allows or denies DHCP server information to be received on those ports. Go Save Settings to Flash section to save the change on the flash to make sure the change is permanent.
TRENDnet User’s Guide TEG-082WS Configure Binding Database Type: Because the IP Address being entered is static, you must select Static. Lease Time: Enter the time that IP address assignment is valid. The range is 10 to 4294967295 seconds. DHCP Snooping > Binding Database The Binding Database displays learned and statically assigned MAC Address and IP Address information for each host on the local area network.
TRENDnet User’s Guide LLDP (Link-Layer Discovery Protocol) TEG-082WS Enable and configure LLDP LLDP > LLDP Global Settings Link Layer Discovery Protocol (LLDP) allows Ethernet network devices, such as switches and routers, to receive and transmit device-related information to directly connected devices on the network and to store data that is learned about other devices. © Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide LLDP Global Settings Enabled: The LLDP feature is active. Disabled: The LLDP feature is inactive. LLDP Settings Message TX Hold Sets the hold multiplier value. The hold time multiplier Multiplier: is multiplied by the transmit interval to give the Time To Live (TTL) that the switch advertises to the neighbors. The range is from 2 to 10. Message TX Sets the transmit interval, which is the interval Interval: between regular transmissions of LLDP advertisements.
TRENDnet User’s Guide View LLDP Neighbor Information LLDP > LLDP Neighbor Information TEG-082WS Port ID: This parameter specifies the neighboring network device’s port number from which the LLDP information was transmitted. Port Description: This parameter describes the neighboring network device’s port. Show Normal: If you click on this button, a detailed report of the neighboring network device will be displayed.
TRENDnet User’s Guide Statistic Statistics provide important information for troubleshooting switch problems at the port level. The Web Management Utility provides a two statistics charts, including Traffic Information and Error Information. View Traffic Information Statistics Statistic > Traffic Information © Copyright 2014 TRENDnet. All Rights Reserved. TEG-082WS Traffic Information Port ID: The port ID on the switch InOctets: Inbound Octets (Bytes/s), number of inbound octet bits in bytes per second.
TRENDnet User’s Guide TEG-082WS View Error Information Statistics Switch Maintenance Statistic > Error Information Upgrade your switch firmware Tools > Firmware Upgrade TRENDnet may periodically release firmware upgrades that may add features or fix problems associated with your TRENDnet switch model and version. To check if there is a firmware upgrade available for your device, please check your TRENDnet model and version using the link. http://www.trendnet.
TRENDnet User’s Guide • Disable sleep mode on your computer as this may interrupt the firmware upgrade process. • Do not upgrade the firmware using a wireless connection, only using a wired network connection. • Any interruptions during the firmware upgrade process may permanently damage your switch. TEG-082WS Firmware Upgrade via HTTP Settings 1. Depending on your web browser, in the Upload Firmware section, click Browse or Choose File. 2.
TRENDnet User’s Guide Firmware Upgrade via TFTP Settings Note: Before using this method, a TFTP server is required alive on the network. The TFTP server has to be in the same subnet. Please place the firmware file (.hex) on the root directory of your TFTP server. If you are not familiar with the TFTP protocol, it is recommended to use the HTTP method.
TRENDnet User’s Guide To restore your switch configuration: 1. Depending on your web browser, click on Browse or Choose File. 2. A separate file navigation window should open. 3. Select the configuration file to restore and click Restore. (Default Filename: config.bin). If prompted, click Yes or OK. 4. Wait for the switch to restore settings. Backup/Restore via TFTP Settings Note: Before using this method, a TFTP server is required alive on the network. The TFTP server has to be in the same subnet.
TRENDnet User’s Guide Cable Diagnostics Test Tools > Cable Diagnostics The switch provides a basic cable diagnostic tool in the GUI for verifying the pairs in copper cabling and estimated distance for troubleshooting purposes. Note: TEG-082WS 3. The test also measures the cable fault and identifies the fault in length according to the distance from the switch. Select the port you want to proceed cable test. Then click on Test Now. The results will be displayed in the Cable Diagnostic Table below.
TRENDnet User’s Guide TEG-082WS Enable IEEE 802.3az Power Saving Mode Reboot/Reset to factory defaults Tools > IEEE 802.3az EEE The IEEE 802.3 EEE standard defines mechanisms and protocols intended to reduce the energy consumption of network links during periods of low utilization, by transitioning interfaces into a low-power state without interrupting the network connection. The transmitted and received sides should be IEEE802.3az EEE compliance. By default, the switch disabled the IEEE 802.
TRENDnet User’s Guide TEG-082WS To reset your switch to factory defaults: Network Connectivity Test (Ping Tool) To reset the switch configurations to factory defaults you can proceed with hardware reset-to-default, or with the web GUI. Hardware reset has the same effect to “reboot the switch to factory default” selection in this session. Tools > Ping This chapter provides the procedure to ping a node on your network from the switch.
TRENDnet User’s Guide PING Test Settings Destination IP The IP address of the node you want to ping in Address: the IPv4 or IPv6 format. Timeout Value: Specifies the length of time, in seconds, the switch waits for a response before assuming that a ping has failed. Number of Pings: Specifies the number of ping requests you want Requests the switch to perform. TEG-082WS Save Settings to Flash Save Settings to Flash Click Start to start the network connectivity ping test.
TRENDnet User’s Guide TEG-082WS Web Smart Switch Management Utility 4. At the Utility installation window, click Next. The TRENDnet Management Utility allows you to do the following: You can easily discover all TRENDnet web smart switches on your network using the discover feature. You can modify the IP address settings, change the admin password, and upgrade firmware for multiple switches. System Requirements Operating System: Windows® 8.
TRENDnet User’s Guide 6. At the Installation, click Install. TEG-082WS Using the Utility Launching the Utility Upon completing the software installation, a desktop shortcut is automatically created. Double-click the icon to start the utility or open the utility if it is already running. Closing the utility will exit the application. You can also click Exit at the bottom of the utility user interface to exit the application. 7. In the Completion window, click Finish.
TRENDnet User’s Guide Discovery List This is the list where you can discover all the Web management devices in your network. TEG-082WS Discovery List MAC Address: IP Address: Protocol version: Product Name: System Name: IP Mode: Location: Subnet Mask: Gateway: Group Interval: Shows the device MAC Address. Shows the current IP address of the device. Shows the version of the Utility protocol. Shows the device product name. Shows the appointed device system name. Shows the DHCP status of the device.
TRENDnet User’s Guide TEG-082WS Device Setting Password Change: You can use this Password Change when you need to change the password, fill in the password needed in the dialog box and then click on Set button to proceed the password change. Configuration Setting: In this Configuration Setting, you can set the IP Address, Subnet Mask, Gateway, Group Interval, System name, Location and IP Mode.
TRENDnet User’s Guide Note: Make sure your computer is in the same sub net with the switch management IP. Otherwise, you are going to have this error message. TEG-082WS Main Menu Options In the File tab, you can find Monitor Save, Monitor Save As, Monitor Load and Exit actions to choose. Access Web: Double click the device in the Monitor List or select a device in the Monitor List and press this “Web Access” button to access the device in Web browser.
TRENDnet User’s Guide TEG-082WS In the Option tab, you can set the Refresh Time and Group Interval. Option Tab Refresh Time: This function helps you to refresh the time of monitoring the device. Choose 15 secs, 30 secs, 1 min, 2 min and 5 min to select the time of monitoring. Group Interval: This is IGMP group interval. The range is from 120 to 1225 seconds. In the Help tab, you can find the utility information with About action, it will show out the version of the Web Management Utility.
TRENDnet User’s Guide TEG-082WS • Speed: 10Mbps (Off), 100Mbps (Orange), Gigabit (Green) • Link/Activity: Connected (Solid Green), Activity (Blinking Green) • Duplex: Full-duplex (Solid Green), Half-duplex (off) • SFP: 10 (Off), 100Mbps (Orange), Gigabit (Green) o 10/100Mbps Activity (Blinking Orange) o Gigabit Activity (Blinking Green) Technical Specifications Hardware Standards: Interface: Cabling Network: Mini-GBIC: IEEE 802.1D IEEE 802.1Q IEEE 802.1S IEEE 802.1X IEEE 802.1p IEEE 802.
TRENDnet User’s Guide MIB: Spanning Tree: Link Aggregation Quality of Service: VLAN: IPv6: IPv6 Neighbor Discovery, IPv6 Static IP, DHCPv6, Auto configuration MIB II RFC 1213 Bridge MIB RFC 1493 Bridge MIB Extension RFC 2674 SNMPv2 MIB RFC 1907 Ethernet Interface MIB RFC 1643 Ethernet –like MIB RFC 2863 Interface Group MIB RFC 2233 MIB Traps Convention RFC 1215 RMON MIB RFC 1757, RFC 2819 802.1p MIB RFC 2674 RADIUS Client Authentication MIB RFC 2618 LLDP-MIB IEEE 802.
TRENDnet User’s Guide TEG-082WS Troubleshooting Q: Q: I typed http://192.168.10.200 in my Internet Browser Address Bar, but If my switch IP address is different than my network’s subnet, what should I do? an error message says “The page cannot be displayed.” How can I access the switch management page? A: 1. Check your hardware settings again. 2. Make sure the Power and port Link/Activity lights are lit. A: You should still configure the switch first.
TRENDnet User’s Guide Appendix How to find your IP address? Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines, however, it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings. TEG-082WS Graphic User Interface MAC OS X 1.
TRENDnet User’s Guide TEG-082WS How to setup a static IP address on your computer’s network card Note: Before setup, make sure that you have a unique static IP address available which will not cause the network address collision. Windows 8 1. Open the Charms bar by moving the mouse to the top right corner of the screen or press the Windows Key + C and click on Search. 2. Type “network” in the search box and click Settings to focus your search. © Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide 3. Choose Network and Sharing Center TEG-082WS 6. Select Internet Protocol Version 4 (TCP/IPv4) and then click Properties. 4. Click Change adapter settings on the left-hand side. 5. Click Properties on the selected network adapter. © Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide 7. Click Use the following address and enter the static IP address and related information. For setting up the TEW-737HRE, you can enter 192.168.10.10 as your IP address, 255.255.255.0 as the Subnet mask. Leave the other fields blank. Click OK to apply the changes. TEG-082WS Windows 7 1. Click Control Panel from the Start menu. 2. Type “network” in the search box to focus your selection. Click on Network and Sharing Center © Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide 3. Click Change adapter settings on the left-hand side. TEG-082WS 5. Select Internet Protocol Version 4 (TCP/IPv4) and then click Properties 4. Click Properties on the selected network adapter. © Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide 6. Click Use the following address and enter the static IP address and related information. For setting up the TEW-737HRE, you can enter 192.168.10.10 as the IP address, 255.255.255.0 as the Subnet mask. Leave other fields blank. Click OK to apply the changes. © Copyright 2014 TRENDnet. All Rights Reserved. TEG-082WS OS X 3. Click the Apple logo in the top-left corner of your screen. Click on System Preferences... . In the Internet and Wireless section, click on Network.
TRENDnet User’s Guide 4. Select the network card you want to configure on the left banner (e.g. Wi-Fi ). Click Advanced. TEG-082WS 6. Click Apply to apply the changes. 5. Choose TCP/IP. In Configure IPv4, select Manually. Input the static IP address, subnet mask, and your router IP address. (In order to setup the TEW-737HRE, you can put in 192.168.10.10 as the IP address, 255.255.255.0 as the subnet mask and leave router in blank. Click OK to exit advanced setup. © Copyright 2014 TRENDnet.
TRENDnet User’s Guide How to find your MAC address? TEG-082WS 2. Select the network card you want to configure on the left banner (e.g. Wi-Fi ). Click Advanced. Windows 2000/XP/Vista/7 Your computer MAC addresses are also displayed in this window, however, you can type getmac –v to display the MAC addresses only. MAC OS X 1. Click the Apple logo in the top-left corner of your screen. Click on System Preferences... . In the Internet and Wireless section, click on Network. 3.
TRENDnet User’s Guide TEG-082WS Regulations Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TRENDnet User’s Guide Europe – EU Declaration of Conformity This device complies with the essential requirements of the Directive 2004/108/EC and 2006/95/EC.
TRENDnet User’s Guide Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. • TEG-082WS – 3 Years Warranty If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer.
