Quick Installation Guide TEG-PCITXR TEG-PCITXRL 3.
Table of Contents English 1. Before You Start 2. How to Install 1 1 2 Troubleshooting 5 Version 03.18.
1. Before You Start ENGLISH Package Contents TEG-PCITXR/TEG-PCITXRL ? ? CD-ROM (Driver) FRANÇAIS ? Multi-Language Quick Installation Guide System Requirements DEUTSCH 32-bit PCI 2.
Note: 1．For Windows 98SE and Me driver installation, refer to the user guide on the Driver CD-ROM. 2．Do not insert the TEG-PCITXR/TEG-PCITXRL until instructed to do so. ENGLISH 2. How to Install FRANÇAIS 1. Insert the Driver CD-ROM into your computer's CD-ROM Drive (Windows Vista/XP/2000). DEUTSCH 2. Click Run autorun.exe (Windows Vista only) 4. Follow the InstallShield Wizard instructions (Windows Vista/XP/2000). 5. Click Yes (Windows 2000 only) 2 ÐÓÑÑÊÈÉ ESPAÑOL 3.
ENGLISH 6. Click Finish (Windows Vista/XP/2000). DEUTSCH 9. Drivers will install automatically. ÐÓÑÑÊÈÉ 8. Insert PCI Card firmly into an available PCI slot, and then turn ON the computer and wait until the Windows desktop appears. ESPAÑOL FRANÇAIS 7. Shutdown your computer and then open your computer's Case. 10. Click Yes (Windows 2000 only).
Register Your Product ÐÓÑÑÊÈÉ To ensure the highest level of customer service and support, please take a moment to register your product Online at: www.trendnet.com/register Thank you for choosing TRENDnet ESPAÑOL Your Installation is complete For detailed information regarding the TEG-PCITXR/TEG-PCITXRL’s configuration and advanced settings, please refer to the Troubleshooting section, User's Guide on the Utility CD-ROM, or TRENDnet's website at http://www.trendnet.com. DEUTSCH FRANÇAIS ENGLISH 11.
Troubleshooting 1. I inserted the Driver CD-ROM into my computer's CD-ROM drive and the installation menu does not appear automatically. What should I do? 1. For Windows Vista, if the installation menu does not appear automatically, click Start, click the Start Search box, and type D:\autorun.exe where "D" in "D:\autorun.exe" is the letter assigned to your CD-ROM Drive, and then press the ENTER key on your keyboard. 2.
2. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Obtain an IP address automatically. Windows Vista 1. Go into the Control Panel, click Network and Internet, click Network and Sharing Center, click Manage Network Connections and then right-click the Local Area Connection icon and then click Properties. 2. Click Internet Protocol Version 4(TCP/IPv4) and then click Properties. Then click on Obtain an IP address automatically. Windows XP/2000/2003Server 1.
4. How do I install the drivers on Windows 98 or ME? Please refer to the User's Guide included on the Driver CD-ROM. 5. Why am I only getting a network connection speed of 100Mbps instead of 1000Mbps? 1. Check the Ethernet Cable. Make sure you are using CAT-5e or CAT-6 Ethernet Cables. Some CAT-5 cables are not rated to run in Gigabit. 2. Make sure you are connected to a 1000Mbps switch.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register Copyright ©2010. All Rights Reserved. TRENDnet.
