Quick Installation Guide TE100-P11 TEW-P11G H/W: V1
Table of Contents Table of Contents English ...................................................................................................... 1. Before You Start ................................................................................. 2. How to Install ..................................................................................... 3. Configure the Print Server ................................................................. 1 1 3 4 Troubleshooting .....................................
1.
Application 2-Port USB/Parallel Print Server (TE100-P11) 4-Port Gigabit Firewall Router (TWG-BRF114) Internet Parallel Printer USB Printer Workstation with Worstation with 10/100Mbps PCI Adapter 10/100Mbps PCI Adapter (TE100-PCIWN) (TE100-PCIWA) Cable/DSL Modem 10/100Mbps Wireless 2-Port USB/Parallel Print Server (TEW-P11G) Workstations with Wireless N USB Adapter (TEW-644UB) Wireless N Home Router (TEW-652BRP) Internet Parallel Printer USB Printer Wireless g 54Mbps 2 English Cable/DSL Modem
2. How to Install Note: Please power off all printers before connecting them to the print server. Then turn on each printer after you make your hardware connections. 1. Connect a RJ-45 network cable from the LAN port on your Router to the LAN port of the Print Server. 2. Connect a Parallel or USB Printer to the printer server. 3. Connect the AC Power Adapter to the Print Server and then to a power outlet. 4. Power ON printer.
3. Configure the Print Server Note: Disable any anti-virus and firewall programs before starting hardware installation. For Windows Users 1. Insert the Utility CD-ROM into your computer's CD-ROM Drive. 2. Click Run autorun.exe (Windows Vista only). 3. Click Setup Wizard. 4. Click Next.
5. Select the print server and then click Next. 6. If desired, change the Device Name, Domain Name and add a Comment (optional). Then click Name. 7. Select the Obtain IP Address automatically and then click Next. Note: If you have the TE100-P11, skip to step 11. If you have the TEW-P11G, continue on step 8. 8. Select the desired wireless network and click Next.
9. The correct wireless settings should be automatically configured. Then click Next. 10. If enabled, enter the encryption key for your wireless network and then click Next. This example shows WPA2-PSK. 11. Click Finish.
12. Click OK. 13. Disconnect the RJ-45 cable and unplug the power. Then plug the power back in (TEW-P11G only). Print Server configuration is now complete. For detailed information regarding adding printers for Windows 98SE/ME/2000/XP/2003 Server/Vista, please refer to the User's Guide on the Utility CD-ROM or TRENDnet's website at www.trendnet.com Register Your Product To ensure the highest level of customer service and support, please take a moment to register your product Online at: www.trendnet.
Troubleshooting Q1. The Setup Wizard is unable to see my printer server. What should I do? A1. First, double check your hardware connections; make sure that the print server is powered ON and is properly connected. Second, click Refresh. Third, disable any software firewall programs (e.g. ZoneAlarm). If your computer is running Windows XP or Vista, disable the built in firewall program. Fourth, unplug the power to the print server, wait 15 seconds, then plug the power back in. Q2.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 USA Copyright ©2008. All Rights Reserved. TRENDnet.
