Quick Installation Guide TK-RP08 H/W: v1.
Table ofofContents Table Contents English ...................................................................................................... 1. Before You Start ................................................................................. 2. How to Install ..................................................................................... 3. Operation and Configuration ............................................................ 1 1 2 5 Troubleshooting ...........................................
1. Before You Start Package Contents ? TK-RP08 ? Quick Installation Guide ? Utility CD-ROM ? RS-232 Cable· ? RJ-45 Ethernet Cables ? Rack Mount Brackets ? Power Cord System Requirements RJ-45 Ethernet Cables ? AC-powered Device ? Windows 98SE/2000/XP/Vista PC required ? TK-IP101 (Optional) ? Broadband/DSL Router (e.g.
2. How to Install Standalone 1. Connect the included Power Cord to the TK-RP08 and then to a power outlet. To TK-RP08 To PC 2. Connect the RS-232 cable from a serial port on your computer to the serial port on the TK-RP08. 3. Connect your AC powered device to one of the eight power outlets on TK-RP08.
Daisy Chain Note: You can daisy chain up to 16 TK-RP08 together, with a maximum of 128 AC powered devices. 1. Connect one end of the provided RJ-45 Ethernet cable to the Daisy Chain Output port on the first TK-RP08 (master). 2. Connect the opposite end of the RJ-45 Ethernet cable to the Daisy Chain Input port on the second TK-RP08 (slave). 3. If you have a third TK-RP08, connect one end of the provided RJ-45 Ethernet cable to the Daisy Chain Output port on the second KVM switch.
Rack Mount The KVM Switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in a wiring closet with other equipment. Note: If you would like to mount the KVM switch to a EIA 19” equipment rack, install the included mounting brackets to the sides of the KVM switch, secure them with the screws provided, and then mount the KVM switch to the equipment rack with the hardware provided by the equipment rack manufacturer. 1.
3. Operation and Configuration LEDs and Push Buttons Current Indicates the amount of current being used. The maximum allowable current is 15 amps. When exceeded, this LED will flash. Push Buttons Press the push buttons to power on and off the power outlet. Press on it for 2 seconds. ALARM When this LED is solid red, the power outlet is not working properly. When this LED is off, the power outlet is working fine.
2. Follow the InstallShield Wizard instructions and then click Finish. 3. Double click the TRENDnet IP Power Manager icon on your desktop. 4. Click on Setting, and then click Connect. 5. Click OK. 6. Click the power button. 7. Click OK.
Troubleshooting Q1: My AC-powered device does not power on after I press on the power button for the power outlet on the TK-RP08. What should I do? A1: First, make sure the provided power cord is plugged into the TK-RP08 and into the power outlet. Second, make sure the AC powered device is properly plugged into one of the power outlets on the TK-RP08. Third, make sure to press the power button for at least two seconds before releasing. Fourth, press the reset button on the TK-RP08.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
TRENDnet Technical Support US . Canada Toll Free Telephone: 1(866) 845-3673 24/7 Tech Support Europe (Germany . France . Italy . Spain . Switzerland . UK) Toll Free Telephone: +00800 60 76 76 67 English/Espanol - 24/7 Worldwide Telephone: +(31) (0) 20 504 05 35 English/Espanol - 24/7 Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 USA Copyright ©2008.
