Quick Installation Guide TK-V201S TK-V401S 1.
Table of Contents English 1. Before You Start 2. How to Install 1 1 2 Technical Specifications Troubleshooting 8 9 Version 05.12.
1. Before You Start ENGLISH Package Contents ? TK-V201S/TK-V401S ? Multi-Language Quick Installation Guide ? Power Adapter (9V DC, 0.5A) FRANÇAIS ? 1 x VGA Male-to-Female Cable (1.
2. How to Install DEUTSCH FRANÇAIS ENGLISH Connecting a Single Computer ESPAÑOL 1. Properly turn OFF your computer and monitors. To Computer To Video Splitter 2 РУССКИЙ 2. Use the provided VGA cable to connect your computer to the VIDEO IN port on the video splitter (TK-V401S shown).
ENGLISH FRANÇAIS 4. Connect the included power adapter to the video splitter and then to a power outlet. 5. Turn on your computer and all connected monitors. 6. Verify the Power LED is lit. ESPAÑOL DEUTSCH 3. Connect your monitor(s) to any of the VIDEO OUT ports on the video splitter.
ENGLISH 1. Connect one end of the provided VGA cable to the VIDEO IN port on the video splitter (TK-V401S shown). FRANÇAIS 2. Connect the opposite end of the provided VGA cable to the Console port on the KVM switch. 4. Connect the included power adapter to the video splitter and then to a power outlet. 5. Refer to your KVM switch's quick installation guide for connecting your computer to the KVM switch. 6. Turn on your computers and all connected monitors. 7. Verify the Power LED is lit.
Note: 1. You can only daisy chain the video splitter with another TK-V201S or TK-V401S. 2. You can daisy chain up to 4 splitters together.
ENGLISH 1. Use the provided VGA cable to connect your computer or KVM Switch to the VIDEO IN port on the first (master) video splitter (TK-V401S shown). FRANÇAIS Computer OR KVM switch 2. Connect one end of a second VGA cable to one of the VIDEO OUT ports on the first (master) video splitter. To Master Video Splitter ESPAÑOL DEUTSCH To Master Video Splitter To Slave Video Splitter 6 РУССКИЙ 3.
5. Connect your monitor(s) to any of the VIDEO OUT port on the video splitter. ENGLISH DEUTSCH FRANÇAIS 4. If you have a third video splitter, connect one end of the VGA cable to the VIDEO OUT port on the second video splitter. Then connect the opposite end of the VGA cable to the VIDEO IN port on the third splitter. Repeat for each additional video splitter. 7. Verify the Power LED is lit. РУССКИЙ ESPAÑOL 6. Connect the included power adapter to each video splitter and then to a power outlet.
Technical Specifications Hardware 8 computers Video Input 1 x USB keyboard Type A Video Output TK-V201S 2 x 15-pin VGA HDB Female TK-V401S 4 x 15-pin VGA HDB Female Resolution 1920 x 1440 Max. Signal Distance WUXGA, HD, UXGA, SXGA+, SXGA, WSXGA, WXGA, XGA, SVGA, VGA, QVGA, and Multisync supported Cable Distance 65 m (210 ft.) max. Daisy-Chain (Cascade) Up to 3 levels Cables (included) 1 x 15-pin VGA cable (male to female), 1.2 m (4 ft.) Power 9V DC, 0.
Troubleshooting 1. My monitors and my PC are on, but I still do not see anything on my monitors. 1. Verify everything is properly connected. See section 2. 2. Verify the power adapter is connected to the video splitter. 3. Verify the Power LED is on. 4. Try plugging the monitor into another Video OUT port. 5. Your monitor could be defective. Try plugging another monitor into the video splitter 2. Does the video splitter support DVI adapters? The video splitter does not support DVI-to-VGA adapters. 3.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDNET'S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register Copyright ©2010. All Rights Reserved. TRENDnet.
