User's Guide
Table Of Contents
- Product Overview
- Switch Installation
- Access your switch management page
- Saving configuration and switch between web modes
- Surveillance Mode Web Interface
- Standard Mode Web Interface
- Status
- Network
- Port
- ONVIF
- PoE (Power over Ethernet)
- VLAN
- Voice VLAN
- MAC VLAN
- Surveillance VLAN
- MAC Address Table
- Spanning Tree (STP, RSTP, MSTP)
- LLDP (Link-Layer Discovery Protocol)
- Multicast
- Configure unknown multicast and multicast forwarding method
- Add static multicast group addresses
- Add multicast router ports
- Configure IGMP snooping settings
- Configure IGMP snooping settings for IPv4 multicast traffic.
- Configure multicast querier settings
- View IGMP snooping statistics
- Configure MLD snooping settings
- Configure MLD snooping settings for IPv6 multicast traffic.
- View MLD snooping statistics
- Configure MVR settings
- Configure MVR port settings
- Configure MVR Group Address Table
- Security
- Configure RADIUS settings
- Configure RADIUS network authentication settings
- Configure RADIUS network port settings
- View authenticated sessions
- Configure Management Access
- Configure Management ACL/ACE (Access Control Lists/Access Control Entries)
- Create new access control list
- Configure Port Security
- Configure Protected Ports
- Configure Storm Control
- Denial of Service (DoS)
- DHCP Snooping
- View DHCP Snooping Statistics
- Configure DHCP Option 82 settings
- Configure DHCP Option 82 Circuit ID settings
- Configure IP Source Guard
- Configure IP Source Guard IMPV Binding
- Save DHCP Snooping Database
- ACL
- QoS
- Diagnostics
- Management
- Modify admin password and create new users
- Upgrade switch firmware
- Backup/Restore switch Configuration
- Save switch configuration to NV-RAM / Restore to default
- SNMP
- Configure the SNMP View Table
- Configure the SNMP Group Table
- Configure the SNMP Community Table
- Configure the SNMP Users
- Set the SNMP Engine ID
- Configure the SNMP Trap Management
- Configure the SNMP Notification
- RMON
- View RMON Statstics
- Configure RMON History Table
- Configure RMON Event Table
- Configure RMON Alarm Table
- Create Schedules
- Technical Specifications
- Troubleshooting
- Appendix
© Copyright 2020 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPE-3012LS / TPE-3018LS
177
Troubleshooting
Q: I typed http://192.168.10.200 in my Internet Browser Address Bar, but an error
message says “The page cannot be displayed.” How can I access the switch
management page?
Answer:
1. Check your hardware settings again. See “Switch Installation” on page 8.
2. Make sure the Power and port Link/Activity and WLAN lights are lit.
3. Make sure your network adapter TCP/IP settings are set to Use the following IP
address or Static IP(see the steps below).
4. Make sure your computer is connected to one of the Ethernet switch ports.
5. Since the switch default IP address is 192.168.10.200, make sure there are no other
network devices assigned an IP address of 192.168.10.200
Windows 7/8/8.1
a. Go into the Control Panel, click Network and Sharing Center.
b. Click Change Adapter Settings, right-click the Local Area Connection icon.
c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4).
d. Then click Use the following IP address, and make sure to assign your
network adapter an IP address in the subnet of 192.168.10.x. Click OK
Windows Vista
a. Go into the Control Panel, click Network and Internet.
b. Click Manage Network Connections, right-click the Local Area Connection
icon and click Properties.
c. Click Internet Protocol Version (TCP/IPv4) and then click Properties.
d. Then click Use the following IP address, and make sure to assign your
network adapter an IP address in the subnet of 192.168.10.x. Click OK
Windows XP/2000
a. Go into the Control Panel, double-click the Network Connections icon
b. Right-click the Local Area Connection icon and the click Properties.
c. Click Internet Protocol (TCP/IP) and click Properties.
d. Then click Use the following IP address, and make sure to assign your
network adapter an IP address in the subnet of 192.168.10.x. Click OK
Note: If you are experiencing difficulties, please contact your computer or operating
system manufacturer for assistance.
Q: I changed the IP address of the switch, but I forgot it. How do I reset my switch?
Answer:
Using a paper clip, push and hold the reset button on the front of the switch and release
after 15 seconds.
The default IP address of the switch is 192.168.10.200. The default user name and
password is “admin”.