Quick Installation Guide TV-H110 H/W: V1
Table of Contents English ...................................................................................................... 1 1. Before You Start ................................................................................ 1 2. Hardware Installation ......................................................................... 2 Troubleshooting ........................................................................................ 13 Version 10.15.
1. Before you start Package Contents TV-H110 ? Quick Installation Guide ? ? Mounting Bracket ? Allen Wrench (5mm) ? Screws, washers and wall mount kit ? IR Shelter ? Power Adapter (12V, 1.5A) Installation Requirements The following items below are not included. Users must provide the items themselves. Make sure to have each item on hand before installation. Internet Camera Server (e.g.
2. Hardware Installation Note: Configure your Internet Camera Server to match your network before installing the device. Hardware Installation 1. Remove the screws from the back of the camera enclosure. Save these screws. You will need to use these screws later. 2. Slide out the back end of the enclosure. 3. Unscrew the circuit board from the metal bracket. Save these screws. You will need to use these screws later.
4. Unscrew the metal bracket from the TV-H110. Save this screw. You will need to use this screw later. 5. Use the following screw to mount the Internet Camera Server to the metal bracket. 6. Connect the IR shelter to the Internet Camera Server (TV-IP312/TV-IP312W only). 7. Take the Internet Camera Server's power adapter and cut about 4 inches from the end of the power connector using the wire cutter. Note: This is the AC adapter that is included with your Internet Camera Server.
8. Take a utility knife and cut along the middle to split the cable into two strands. 9. Use a wire stripper to remove the insulation to expose the copper wiring. 10. Run the Internet Camera Server's power adapter and RJ-45 Ethernet cable from the base to the top of the mounting arm. Make sure the end of the RJ-45 Ethernet cable that is run through the top of the TV-H110 is unterminated. 11. Run the TV-H110's power jumper cable from the top to the base of the camera housing. 12.
13. Remove one of the caps from the enclosure. 14. Insert the unterminated end of the Ethernet cable through the cap. 15. Terminate the Ethernet cable. 16. Insert the Ethernet cable through the hole. Then screw in the cap securely. 17. Remove an unused cap from the enclosure.
18. Insert the Internet Camera Server's power adapter through the cap. 19. Insert the Internet Camera Server's power adapter cable through the hole. Then screw in the cap securely. 20. Connect the two ends of the power adapter back by twisting the copper wiring. Make sure you do not cross the copper wires. 21. Use electrical tape to seal the cables back together. Make sure to seal the individual strands separately. 22. Screw the metal bracket back into the Internet Camera Server.
23. Screw the circuit board back to the metal bracket. 24. Connect the power adapter to the Internet Camera server. 25. Connect the Ethernet cable to the Internet Camera server. 26. Slide the back end of the enclosure back in. 27. Secure the screws into the back of the camera enclosure.
Installing External Antenna to Wireless Internet Camera Note: Before installation, you need the following products: TEW-ASAK (v2.0R), TEW-L406 or TEW-L412 and an External Antenna (TEW-AO14D). 1. Remove the antenna from the back of your wireless Internet Camera Server. 2. Run the TEW-ASAK from the base to the top of the mounting arm. 3. Follow steps 1-6 in the Hardware Installation section above. 4. Remove one of the caps from the enclosure.
5. Insert the TEW-ASAK through the cap. 6. Insert the TEW-ASAK through the hole. Then screw in the cap securely. 7. Please follow the previous section for installing the power adapter to the Internet Camera Server. 8. Screw the metal bracket back in to the Internet Camera Server. 9. Screw the circuit board back to the metal bracket.
10. Connect the TEW-ASAK and the power adapter to the Internet Camera Server. 11. Slide the back end of the enclosure back in. 12. Secure the screws into the back of the camera enclosure. 13. Follow the directions in the QIG for the TEW-ASAK to connect the surge arrestor to your outdoor antenna (e.g. TEW-AO14D).
Mounting the Camera Housing 1. Place the mounting bracket against the wall and mark each of the four holes with a pencil. 2. Drill holes for the screws at each marked position. Make sure the drill bit matches the size of the provided white screws. 3. Insert the screws into the holes. 4. Use the bracket screws to mount the mounting bracket to the TVH110. Use the provided Allen wrench to secure the mounting bracket.
5. Adjust the mounting bracket to the desired position. Then use the provided Allen wrench and turn it clockwise to secure position. 6. Align the Wall Mount bracket with the screws, and then use the provided nuts and washers to secure it. Your installation is now complete. Register Your Product To ensure the highest level of customer service and support, please take a moment to register your product Online at: www.trendnet.
Troubleshooting Q1: After I put my Internet Camera Server in the enclosure, the image is distorted. What should I do? A1: First, make sure that you have adjusted the focus on your camera. Second, mount the TV-H110 so that it's not in direct view of the sun. Third, if you are using a day/night camera with an auto iris lens, make sure to push the camera all the may to the front so that the IR shelter is touching the glass.
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF
Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation. Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with you Local Authority or Retailer for recycling advice.
Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 USA Copyright ©2008. All Rights Reserved. TRENDnet.
