Quick Installation Guide TV-NVR2208/TV-NVR2216/TV-NVR2432(V1)
Table of Content 1 English 1. Before you start 2. Installation 3.
1. Before You Start Package Contents Ÿ NVR (No HDD installed) Ÿ CD-ROM (Utility & User's Guide) Ÿ Power Adapter or Power Cord (depending on your model) Ÿ Network cable (1.8 m / 6 ft.) Ÿ HDMI cable (1.8 m / 6 ft.
2. Installation Note: Before you install the NVR please ensure that all cameras are configured and available on the network. 2.1 Hard Drive Installation Note: Ÿ Static Electricity can damage the NVR. Before handling the unit, discharge any static electricity, or use an anti-static wrist strap. Ÿ The NVR supports SATA I and II drives. 1. Remove the retaining screws from the top panel of the NVR. 2. Slide the cover off the unit by pulling the top cover towards the rear panel.
3. Attach the SATA data and power cables to the hard disc drive, then connect the SATA cable and the molex connect or the control board. 4. Mount the hard drives to the drive bays of the NVR using the mounting screws, screwing from the underside of the NVR into the hard drive case. 5. Slide the top cover back on the NVR, and reinstall the screws holding the panel in place.
2.2 Wiring 1. Connect an HDMI cable or a VGA cable (not included) from your display to the NVR's HDMI or VGA port on the rear panel. Grounding point Display (Not included) or VGA cable not included Display VGA IN HDMI (Not included) 2. Connect the included mouse to the front or rear USB port on the NVR. For ease of configuration you can also connect a USB keyboard (not included) to the NVR.
3. Connect network cable to the LAN1 port and connect the other end to your network. 4. Attach the power adapter or power cord (rear panel) and plug the unit into an electrical outlet.
2.3 System Setup 1. Turn the NVR by toggling the power switch to the “on” position. Follow the onscreen wizard to configure the NVR. The first screen requires you to change the password, for security purposes TRENDnet recommends that you change the default password on the NVR. Enter a new password, confirm it and then click OK. Set Password Username admin New Password ******** Confirm Password... ******** Weak Enter new password.
3. The Setup Wizard will start each time you restart the NVR. You can disable the wizard by unchecking “Start wizard when device starts?” then click “Next”. Wizard Start wizard when device starts? Next Exit 4. Enter the password again then click “Next”. Wizard Admin Password New Admin Password New Password Confirm Enter new password. For your security new password must be between 8 and 16 characters and contain at least one: Special character ( !, @, #, $ ) Alphanumeric (1, 2, 3, etc.
5. Set the time and date on the NVR then click “Next”. Wizard Time Zone Date Format System Date 05: 05: 2016 System Time 06: 15: 27 Previous Next Exit 6. Configure the IPv4 address of the NVR, select DHCP to get an IP address from your network, then click “Next”. Wizard Network Type 10/100/1000 Self-adaptive Enable DHCP Clicent Ipv4 Address 192 .168 .10 .60 Ipv4 Subnet Mask 255 .255 .255 .0 Ipv4 Default Gateway . . . Primary Default Server Secondary DNS Se...
7. Configure the desired port values and dynamic DNS account information then click “Next”. Wizard Server Port 8000 HTTP Port 80 RTSP Port 554 Enable UPnP Enable DDNS DDNS Type dyn.com Sever Address Device Domain Name Status DDNS is not enabled. Username Password Previous Next Exit 8. The installed disk drives must be initialized prior to use. Click on the “Init” button to initialize the drives. L... 1 Capacity 149.
9. Initializing the drives will erase all data on them. Click “OK” on the warning pop-up then click “OK” after the drives finish initializing to complete the setup wizard. L... 1 Capacity 149.02GB Status Normal Property RW Type Local Free Space 0MB Initialize Initialization will erase all data on the HDD. Continue? 10. The NVR will scan the network for available cameras. If your cameras do not appear, click the “Search” button to rescan the network. Select the desired cameras then click “Add”.
11. Configure the NVR to continuously record at all times or to record only motion detected events then click “OK”. Continuous Motion Detection 12. Congratulations! You have completed the configuration of the NVR. You can now view live cameras and access additional options by right clicking on the display to bring up the configuration menu. Note: Remote access to the NVR requires port forwarding in your router. Forward the HTTP and RTSP ports in use by the NVR in the router settings to the NVR.
3. App Scan the QR codes here to install the TRENDnet IPView app on your phone. Android iOS 1. Open TRENDnet IPView and tap on Add option .
2. Enter the NVR's IP address (remote IP), port number, and login information then tap icon 3. Tap on List from the menu and enable the specific NVR and tap Connect to view.
4. Added cameras will display. 5. App setup is complete. For details information on how to manage the NVR, please refer to the User's Guide on the CD-ROM.
Manufacturer’s Name and Address TRENDnet, Inc. 20675 Manhattan Place Torrance, CA 90501 USA Product Information: Model Number: TV-NVR2208 / TV-NVR2216 / TV-NVR2432 Trade Name: TRENDnet TRENDnet hereby declare that the product is in compliance with the essential requirements and other relevant provisions under our sole responsibility.
Safety notes Before using your TRENDnet device for the first time, it is essential to read and understand all safety and operating instructions. Keep instructions in a safe place for future reference. Some TRENDnet products are rated for outdoor applications and can sustain certain weather conditions. Please refer to the product's Ingress Protection (IP) rating and the operating humanity and temperature range. DANGER due to electricity Warning: Never open TRENDnet devices.
GPL/LGPL General Information This TRENDnet product includes free software written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. The details of the GNU GPL and LGPL are included in the product CD-ROM. Please also go to (http://www.gnu.org/licenses/gpl.
TV-NVR2208/TV-NVR2216/TV-NVR2432 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following length of time from the date of purchase. Warranty: 2 year limited warranty (When Applicable: 1 year warranty for power adapter, power supply, and cooling fan components.) Visit TRENDnet.com to review the full warranty policy, rights, and restrictions for this product.
