Network Bullet Camera·Quick Start Guide Quick Start Guide COPYRIGHT © 2015 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”).
Network Bullet Camera·Quick Start Guide Legal Disclaimer TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY.
Network Bullet Camera·Quick Start Guide IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS. Regulatory Information FCC Information Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Network Bullet Camera·Quick Start Guide This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
Network Bullet Camera·Quick Start Guide Industry Canada ICES-003 Compliance This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Network Bullet Camera·Quick Start Guide rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
Network Bullet Camera·Quick Start Guide ● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 24 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information. ● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard. ● Please make sure that the plug is firmly connected to the power socket.
Network Bullet Camera·Quick Start Guide ● The sensor may be burned out by a laser beam, so when any laser equipment is in using, make sure that the surface of sensor will not be exposed to the laser beam. ● Do not place the camera in extremely hot, cold (the operating temperature shall be-30°C ~+60°C, or -40°C ~ +60°C if the camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation.
Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ............................................................... 11 1.1 Overview of Type I Bullet Camera ................................. 11 1.2 Overview of Type II Bullet Camera ................................ 12 1.2.1 Micro SD Card Slot & Reset/ WPS Button ........... 13 1.2.2 PoE Power Supply Configuration (Optional)........ 17 2 Installation ...............................................................................
Network Bullet Camera·Quick Start Guide 1 Appearance Description 1.1 Overview of Type I Bullet Camera 1 3 2 5 4 Figure 1-1 Type I Bullet Camera Table 1-1 Description No. Description No. Description 1 Mounting Base 4 Lens 2 Back Box 5 Sun Shield 3 Front Box 6 Type I camera does not support the function of Wi-Fi and SD card.
Network Bullet Camera·Quick Start Guide 1.
Network Bullet Camera·Quick Start Guide Table 1-2 Description No. Description No. Description 1 Mounting Base 7 LED Indicator 2 Adjustment Nut 8 SD Card Slot 3 Main Body 9 10/100M Self-adaptive Ethernet Interface 4 Sun Shield 10 Power Cable 5 Lens 11 GND Screw 6 Reset/ WPS Button 12 PoE Power Cable (Optional) 1.2.1 Micro SD Card Slot & Reset/ WPS Button Move the Micro SD / Reset/WPS Cover aside, and you can see the Reset button, WPS button and the micro SD card slot.
Network Bullet Camera·Quick Start Guide Installing the SD Card Insert the micro SD card into the micro SD card slot. SD Card Slot Figure 1-4 Install the SD Card Resetting the Camera Press WPS/RESET about 10s when the camera is power on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
Network Bullet Camera·Quick Start Guide WPS/RESET Figure 1-5 WPS/Reset Button Setting the WPS Protocol A wireless router with the WPS function is required to enable the WPS function of the camera. Refer the steps below. Steps: 1. Press the WPS button on the router. 2. Press the WPS button (about 2s) on the camera within 120s you enable the WPS of the router to join in the wireless network.
Network Bullet Camera·Quick Start Guide WPS/RESET Figure 1-6 WPS/Reset Button The WPS button works as a reset button only when you press it when the camera is powering on. Press the WPS button on the camera, and then press the WPS button on the router will work as well, and the expire time of WPS connection on the camera is 120s. The link indicator blinks if the wireless connection succeeded. Screw the Micro SD / Reset/WPS Cover back to the camera after all settings.
Network Bullet Camera·Quick Start Guide 1.2.2 PoE Power Supply Configuration (Optional) This type of bullet camera support PoE power supply. The connection of PoE power cables is shown as follows. Connect the single-cable end to the PoE router. Connect the power and Ethernet cables on the other end to the corresponding cables of the camera.
Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12V DC or 24V AC, please make sure your power supply matches with your camera. ● Make sure all the related equipment is power-off during the installation. ● Check the specification of the products for the installation environment.
Network Bullet Camera·Quick Start Guide 2.1 Installation of the Bullet Camera Both wall mounting and ceiling mounting are suitable for the IR bullet camera. Wall mounting will be taken as an example in this section. You can take steps of wall mounting as a reference if ceiling mounting is adopted. Steps: 1. Drill the screw holes in the wall according to the drill template. Ceiling Mounting Hole Hole Hole Figure 2-1 Drill Template 2. Route the corresponding cables. 3.
Network Bullet Camera·Quick Start Guide Figure 2-2 Secure the Camera to the Ceiling 4. Connect the corresponding power/ Video Output cables. 5. Adjust the Lens. 1). Loosen the adjustable nut. 2). Adjust the pan direction [0°~360°]. 3). Adjust the tilt direction [0°~90°]. 4). Rotate the camera [0~360°] to adjust the lens to the surveillance angle. 5). Tighten the adjustable nut to complete the installation.
Network Bullet Camera·Quick Start Guide Adjust Nut 0°~360° 0°~360° 0°~90° Figure 2-3 3-axis Adjustment 2.2 Installation of Water-proof Jacket It is recommended to adopt the water-proof jacket (supplied) for the network interface when the camera is installed outdoor. Steps: 1. If the network cable has been settled down, cut off the plug of the network cable first. 2.
Network Bullet Camera·Quick Start Guide 6. Wrap the network interface with the main body of the water-proof jacket, and then rotate the fix nut clockwise to assemble it to the main body of the water-proof jacket.
Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the LAN Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. 3.
Network Bullet Camera·Quick Start Guide 3.2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation. Please refer to the User Manual of Network Camera for Activation via Client Software. 3.2.
Network Bullet Camera·Quick Start Guide Figure 3-3 Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide 3.2.2 Activation via SADP Software SADP software is used for detecting the online device, activating the camera, and resetting the password. Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods. Steps: 1. Run the SADP software to search the online devices. 2.
Network Bullet Camera·Quick Start Guide 3. Create a password and input the password in the password field, and confirm the password. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
Network Bullet Camera·Quick Start Guide Note: Please refer to Chapter 3.2 to activate the camera if the camera is inactive. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Figure 3-5 Modify the IP Address 4. Input the password to activate your IP address modification. The batch IP address modification is supported by the SADP; please refer to the User Manual of SADP for details.
Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps: 1. Open the web browser. 2.
Network Bullet Camera·Quick Start Guide 4. Click Login. Figure 4-1 Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. You may have to close the web browser to finish the installation of the plug-in.
Network Bullet Camera·Quick Start Guide Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in (1) 31
Network Bullet Camera·Quick Start Guide Figure 4-4 Install Plug-in (2) 6. Reopen the web browser after the installation of the plug-in and repeat steps 2~4 to login. For detailed instructions of further configuration, please refer to the user manual of network camera.
0