Assembly Instruction Sheet

ManualsBrandsTrent Austin Design ManualsCeiling LightsTristin 5 - Light Kitchen Island Linear Pendant

Package Contents

1of2

Fixture Body

6” Rod

12” Rod

Hardware Contents

Crossbar

Assembly

Fixture Loop

STEP 1 Install the Crossbar Assembly to Outlet Box and Adjust

the length of the Nipple

A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head

of the Green Ground Screw facing you. Secure it with Outlet Box

Screws (not included), tighten until snug

B. Adjust the hex nut and lock washer underside of the crossbar to the

middle of the nipple.

C. Remove the knob from the nipple. Place the Ceiling Canopy (CC)

over the nipple against the ceiling to determine the correct position

(5)MediumBase60WVintageBulbs(supplied),100WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Vintage Bulb

Quick Link

Ceiling

Canopy

Outlet Box Screw

(not included)

Hex Nut and

Lock Washer

Outlet Box

Green Ground Screw

Knob

Figure 1

Nipple

(Step 1 Continued)

of the nipple. Thread the knob onto the nipple. Adjust the nipple to

allow the Ceiling Canopy (CC) to rest against the ceiling when held

in place by the knob.

D. Remove the knob and the Ceiling Canopy (CC). Tighten the lock

washer and the hex nut against the crossbar to secure in place.

STEP 2 Assemble Rods, Fixture Loops and Ceiling Canopy-

A. Determine the Rods (C/D) to be assembled to the Fixture Body (B)

according to your hanging height.

B. Pass the supply wires and ground wire through the chosen rods

(C/D) and one Fixture Loop (A). Thread the Fixture Body (B), the

chosen Rods (C/D) and the Fixture Loops (A) together. Hand

tighten until snug.

C. Pass the supply wires and ground wire through the Ceiling Canopy

(CC). Attach the Fixture Loops (A) to Ceiling Loops underside of the

Ceiling Canopy (CC) with Quick Links (BB).

Suggested rods for Ceiling height :

8’ ceiling : use (1) 6” rod and (1) 12” rod

9’ ceiling : use (1) 6” rod and (2) 12” rods

10’ ceiling: use (2) 6” rods and (2) 12” rods

Figure 2

STEP 3 - Attach the Lanyard

A. The purpose of the lanyard is to provide a means to support the

fixture hands free from the junction box while connecting the

electrical wires.

Thank you for purchasing a our product.

Need assistance with parts or assembly? Call our customer service or visit us on-line

B. Turn the Button Stop so it may be inserted into a Crossbar slot. Make

sure the Button Stop is completely inside the Crossbar. Slowly

Assembly Instruction Sheet

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) Medium Base 60W Vintage Bulbs (supplied), 100W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present.
PAGE 2
(Step 3 Continued) FINISH: BRUSHED NICKEL release the fixture to make sure it is supported by the Button Stop. Proceed to the wiring steps in the next step. Once you are complete with the wiring, the Lanyard will push into the junction box when the fixture is placed for final mounting. Slot Crossbar Button Stop Lanyard Figure 3 4.5” STEP 4 - Making the Wire Connections 9” A. Use standard wire connectors (not included) to make all wire connections.