Owner's Manual

ManualsBrandsTrent Austin Design ManualsDesksHovey L-Shape Executive Desk

Business or pleasure.

Works both ways.

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

Enlish p 1-34

Français p 35-39

Español p 40-44

Summary of content (47 pages)

PAGE 1
Business or pleasure. Works both ways. NOTE: THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
PAGE 2
Table of Contents Assembly Tools Required Part Identiﬁcation 3 Hardware Identiﬁcation 4 Assembly Steps Français 5-34 35-39 Español 40-44 Safety 45-46 Warranty Page 2 No. 2 Phillips Screwdriver Tip Shown Actual Size 47 Skip the power trip. This time.
PAGE 3
Now you know our ABCs. Part Identiﬁcation å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge to help distinguish similar parts from each other. Use this part identiﬁcation to help identify similar parts.
PAGE 4
Hardware Identiﬁcation å Screws are shown actual size. You may receive extra hardware with your unit.
PAGE 5
Step 1 å Assemble your unit on a carpeted ﬂoor or on the empty carton to avoid scratching your unit or the ﬂoor. å Push ten HIDDEN CAMS (5) into the BACKS (B and E), UPRIGHT (F), and END (H). H F Arrow 5 (10 used) E B Arrow Arrow 5 Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
PAGE 6
Step 2 å Push fourteen SMALL HIDDEN CAMS (6) into the DRAWER SIDES (T, V, X and Z) and SMALL BACK (CC). Arrow (14 used) 6 6 Arrow CC Z Arrow 6 X V T Arrow Hole The arrow in the HIDDEN CAM must point toward the hole in the edge of the board.
PAGE 7
Step 3 å Turn twenty-four CAM SCREWS (7) into the LEFT TOP (C), RIGHT TOP (D), UPRIGHT (F), RIGHT END (H), SHELF (DD), SMALL DRAWER FRONT (S) and LARGE DRAWER FRONT (W).
PAGE 8
Step 4 å Fasten four METAL BRACKETS (10) to the RIGHT END (H) and LEFT UPRIGHT (F). Use four BLACK 1/2" PAN HEAD SCREWS (22). å NOTE: Be sure the METAL BRACKETS are even with edges of the END and UPRIGHT. å NOTE: Be sure to position the BRACKETS exactly as shown.
PAGE 9
Step 5 å Fasten the UPRIGHT LEG (G) to the UPRIGHT (F). Use two BLACK 1/2" PAN HEAD SCREWS (22) through the METAL BRACKETS on the UPRIGHT and into the UPRIGHT LEG. å Fasten the RIGHT END LEG (J) to the RIGHT END (H). Use two BLACK 1/2" PAN HEAD SCREWS (22) through the METAL BRACKETS on the RIGHT END and into the RIGHT END LEG.
PAGE 10
Step 6 å Fasten the UPRIGHT LEG (G) to the UPRIGHT (F) as shown in the left diagram. Use two BLACK 2" PAN HEAD SCREWS (16). å Fasten the RIGHT END LEG (J) to the RIGHT END (H ) as shown in the right diagram. Use two BLACK 2" PAN HEAD SCREWS (16).
PAGE 11
Step 7 å Fasten the EXTENSION BLOCKS (R) to the RIGHT END (H) and UPRIGHT (F). Use eight BLACK 1" FLAT HEAD SCREWS (19). 19 BLACK 1" FLAT HEAD SCREW (8 used in this step) These small holes must be here. J R R H G R F R These small holes must be here.
PAGE 12
Step 8 å Separate the EXTENSION SLIDES (4) from the EXTENSION RAILS (3) as shown in the upper diagram below. Be prepared, the parts are greasy. å Fasten the EXTENSION RAILS (3) to the EXTENSION BLOCKS (R) on the RIGHT END (H) and UPRIGHT (F). Use four BLACK 1/2" FLAT HEAD SCREWS (23). å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge of the EXTENSION RAIL in to ﬁnd the other hole that lines up with the hole in the END and UPRIGHT.
PAGE 13
Step 9 å Fasten the RIGHT DRAWER SLIDE (2) to the EXTENSION RAIL (R) on the RIGHT END (H). Use two BLACK 1/2" FLAT HEAD SCREWS (23). å Fasten the LEFT DRAWER SLIDE (1) to the EXTENSION RAIL (R) on the UPRIGHT (F). Use two BLACK 1/2" FLAT HEAD SCREWS (23). 23 BLACK 1/2" FLAT HEAD SCREW (4 used in this step) 2 Use the 6th hole from the end of the DRAWER SLIDE.
PAGE 14
Step 10 å Fasten the SHORT BRACES (Q) to the UPRIGHT LEG (G). Turn three BLACK 1/2" HEX HEAD SCREWS (21) with the L-WRENCH (13). Remember: Righty tighty. Lefty loosey. 21 BLACK 1/2" HEX HEAD SCREW (3 used in this step) 13 Q Q The hole should be closer to this edge. The hole should be closer to this edge. G Q The hole should be closer to this edge.
PAGE 15
Step 11 å Fasten the SMALL BACK (CC) to the UPRIGHT (F). Tighten two HIDDEN CAMS. 1 2 Four HIDDEN CAMS should be here.
PAGE 16
Step 12 å Fasten the RIGHT END LEG (J) to the SHORT BRACES (Q) and SMALL BACK (CC). Turn three BLACK 1/2" HEX HEAD SCREWS (21) with the L-WRENCH (13). Tighten two HIDDEN CAMS.
PAGE 17
Step 13 å å Carefully stand your unit upright. Fasten the SHELF (DD) to the UPRIGHT (F), RIGHT END (H), and SMALL BACK (CC). Tighten six HIDDEN CAMS.
PAGE 18
Step 14 å Fasten the LEGS (G and J) to the RIGHT TOP (D). Use four BLACK 1-9/16" PAN HEAD SCREWS (17). 17 BLACK 1-9/16"" PAN HEAD SCREW (4 used in this step) G J This hole must be here.
PAGE 19
Step 15 å Fasten the RIGHT BACK (E) to the RIGHT TOP (D). Tighten three HIDDEN CAMS. å Fasten the RIGHT BACK (E) to the UPRIGHT LEG (G). Use two BLACK 2" PAN HEAD SCREWS (16).
PAGE 20
Step 16 å Fasten the RIGHT BACK BRACE (M) to the RIGHT BACK (E). Use three BLACK 2" FLAT HEAD SCREWS (16). å å Position the RIGHT BACK BRACE exactly as shown. Next, fasten the RIGHT BACK BRACE (M) to the UPRIGHT LEG (G). Use a BLACK 1/2" PAN HEAD SCREW (22) through the tab and into the UPRIGHT LEG (G).
PAGE 21
Step 17 å Fasten the CORNER LEG (EE) to the RIGHT BACK (E). Use two BLACK 2" PAN HEAD SCREWS (16). å Fasten the CORNER LEG (EE) to the RIGHT BACK BRACE (M). Turn a BLACK 1/2" HEX HEAD SCREW (21) with the L-WRENCH (13).
PAGE 22
Step 18 å Fasten the RIGHT LOWER BRACE (N) to the UPRIGHT LEG (G) and CORNER LEG (EE). Use four BLACK 1/2" PAN HEAD SCREWS (22). å Fasten the RIGHT FRONT BRACE (P) to the UPRIGHT LEG (G). Use two BLACK 1/2" PAN HEAD SCREWS (22). å å NOTE: Position the RIGHT FRONT BRACE exactly as shown. Fasten the RIGHT FRONT BRACE (P) to the RIGHT TOP (D). Use three BLACK 1-9/16" PAN HEAD SCREWS (17).
PAGE 23
Step 19 å Fasten the LEFT FRONT BRACE (O) to the LEFT LEG (A). Turn a BLACK 1/2" HEX HEAD SCREW (21) with the L-WRENCH (13). Don't worry. It isn't Rome. This can be built in a day. 21 BLACK 1/2" HEX HEAD SCREW (1 used in this step) A 13 O These edges must be even.
PAGE 24
Step 20 å Fasten the LEFT LEG (A) and LEFT FRONT BRACE (O) to the LEFT TOP (C). Use ﬁve BLACK 1-9/16" PAN HEAD SCREWS (17).
PAGE 25
Step 21 å Fasten LEFT BACK (B) to the LEFT TOP (C). Tighten three HIDDEN CAMS. å Fasten the LEFT BACK (B) to the LEFT LEG (A). Use two BLACK 2" PAN HEAD SCREWS (16).
PAGE 26
Step 22 å Fasten the LEFT BACK BRACE (K) to the LEFT LEG (A). Turn a BLACK 1/2" HEX HEAD SCREW (21) with the L-WRENCH (13). å Fasten the LEFT BACK BRACE (K) to the LEFT BACK (B). Use three BLACK 2" PAN HEAD SCREWS (16). 21 13 BLACK 1/2" HEX HEAD SCREW (1 used in this step) A 16 BLACK 2" PAN HEAD SCREW (3 used in this step) K B Page 26 The LEFT BACK BRACE should sit on the LEFT BACK.
PAGE 27
Step 23 å Fasten the LEFT BACK (B) to the CORNER LEG (EE). Use two BLACK 2" PAN HEAD SCREWS (16). å Fasten the LEFT BACK BRACE (K) to the CORNER LEG (EE). Turn a BLACK 1/2" HEX HEAD SCREW (21) with the L-WRENCH (13). å Fasten the RIGHT FRONT BRACE (P) to the LEFT FRONT BRACE (O). Turn a BLACK 1-3/8" HEX HEAD SCREW (18) with the L-WRENCH (13). å Fasten the LEFT BACK (B) to the RIGHT FRONT BRACE (P). Turn a BLACK 1-3/8" HEX HEAD SCREW (18) with the L-WRENCH (13).
PAGE 28
Step 24 å Fasten the LEFT LOWER BRACE (L) to the LEFT LEG (A) and CORNER LEG (EE). Use four BLACK 1/2" PAN HEAD SCREWS (22).
PAGE 29
Step 25 YO UR UN IT O N TH E\ å Carefully turn your unit onto the RIGHT BACK (E) as shown in diagram #2. Then, stand your unit upright as shown in diagram #3. TU R N TO å You will need help in this step. Follow the direction of the arrows on how to stand your unit upright.
PAGE 30
Step 26 1 2 19 BLACK 1" FLAT HEAD SCREW (4 used in this step) Y X Z BB Fi su nis rf he ac d e Y Z X Groove å Fasten the LARGE DRAWER SIDES (X and Z) to the LARGE DRAWER BACK (Y). Use four BLACK 1" FLAT HEAD SCREWS (19). å With the palm of your hand, push the DRAWER BOTTOM into the grooves. Slide the LARGE DRAWER BOTTOM (BB) into the grooves in the LARGE DRAWER SIDES (X and Z) and LARGE DRAWER BACK (Y). 3 1 2 Z X Be sure the DRAWER BOTTOM inserts into the DRAWER FRONT groove.
PAGE 31
Step 27 å Fasten the EXTENSION SLIDES (4) to the LARGE DRAWER SIDES (X and Z). Use four BLACK 1/2" FLAT HEAD SCREWS (23). å å NOTE: Use the exact holes shown. å Push the RIGHT FILE GLIDE (14) onto the top edge of the LARGE RIGHT DRAWER SIDE (Z). å Push the LEFT FILE GLIDE (15) onto the top edge of the LARGE LEFT DRAWER SIDE (X). Fasten a KNOB SET (9) to the LARGE DRAWER FRONT (W). Use a BLACK 1" MACHINE SCREW (20).
PAGE 32
Step 28 1 2 19 BLACK 1" FLAT HEAD SCREW (4 used in this step) With the palm of your hand, push the DRAWER BOTTOM into the grooves. U V V U T å Fi su nis rf he ac d e Groove T AA Fasten the SMALL DRAWER SIDES (T and V) to the SMALL DRAWER BACK (U). Use four BLACK 1" PAN HEAD SCREWS (19). å 3 4 1 Slide the SMALL DRAWER BOTTOM (AA) into the grooves in the SMALL DRAWER SIDES (T and V) and SMALL DRAWER BACK (U).
PAGE 33
Step 29 å å Fasten the SMALL DRAWER SIDES (T and V) to the DRAWER SLIDES (1 and 2). Use four BLACK 1/2" FLAT HEAD SCREWS (23) through the tabs of the DRAWER SLIDES (1 and 2). Almost time to celebrate! With a nap. Peel a BUMPER from the BUMPER CARD (8) and stick them on the back surface of the SMALL DRAWER FRONT (S).
PAGE 34
Step 30 å å å Push two GROMMETS (11) into the holes in the BACKS (B and E). å å NOTE: Please read the back pages of the instruction booklet for important safety information. Push two GROMMETS WITH CAPS (12) into the holes in the TOPS (C and D). To insert the large drawer into your unit, line up the EXTENSION SLIDES on the large drawer with the EXTENSION RAILS on the unit and push the large drawer into the unit until it is fully inserted.
PAGE 35
Utilisez les instructions d’assemblage en français avec les schémas étape par étape du manuel d’instruction en anglais. Chaque étape en français correspond à la même étape en anglais. La pièce devant être attachée à l’élément est représentée en gris sur les schémas de chaque étape pour plus de précision. Comparer la “Liste de pièces” ci-dessous avec la “PART IDENTIFICATION” du manuel en anglais pour vous familiariser avec les pièces avant l’assemblage.
PAGE 36
ÉTAPE 1 ÉTAPE 7 Assembler l'élément sur un sol à moquette ou sur le carton vide pour éviter d'endommager l'élément ou le sol. Fixer les BLOCS D'EXTENSION (R) à l’EXTRÉMITÉ DROITE (H) et au MONTANT (F). Utiliser huit VIS TÊTE PLATE 25 mm NOIRES (19). Enfoncer dix EXCENTRIQUES ESCAMOTABLES (5) dans les ARRIÈRES (B et E), le MONTANT (F) et l’EXTRÉMITÉ (H). ÉTAPE 2 Enfoncer quatorze PETITES EXCENTRIQUES ESCAMOTABLES (6) dans les CÔTÉS DE TIROIR (T, V, X et Z) et le PETIT ARRIÈRE (CC).
PAGE 37
ÉTAPE 13 ÉTAPE 19 Relever, avec précaution, l'élément dans sa position verticale. Fixer l’ENTRETOISE AVANT GAUCHE (O) au PIED GAUCHE (A). Faire tourner une VIS TÊTE HEX 13 mm NOIRE (21) avec la CLÉ EN L (13). Fixer la TABLETTE (DD) au MONTANT (F), à l’EXTRÉMITÉ DROITE (H) et PETIT ARRIÈRE (CC). Serrer six EXCENTRIQUES ESCAMOTABLES. ÉTAPE 14 ÉTAPE 20 Fixer les PIEDS (G et J) au DESSUS DROIT (D). Utiliser quatre VIS TÊTE GOUTTE DE SUIF 40 mm NOIRES (17).
PAGE 38
ÉTAPE 24 ÉTAPE 27 Fixer l’ENTRETOISE INFÉRIEURE GAUCHE (L) au PIED GAUCHE (A) et au PIED DU COIN (EE). Utiliser quatre VIS TÊTE GOUTTE DE SUIF 13 mm NOIRES (22). Fixer les COULISSES D'EXTENSION (4) aux CÔTÉS DE GRAND TIROIR (X et Z). Utiliser quatre VIS TÊTE PLATE 13 mm NOIRES (23). REMARQUE : Utiliser les trous exacts indiqués. ÉTAPE 25 Fixer un ENSEMBLE DE BOUTONS (9) sur le DEVANT DE GRAND TIROIR (W). Utiliser une VIS À MÉTAUX 25 mm NOIRE (20). Faire appel à une autre personne pour cette étape.
PAGE 39
ÉTAPE 29 ÉTAPE 30 Fixer les CÔTÉS DE PETIT TIROIR (T et V) aux COULISSES DE TIROIR (1 et 2). Utiliser quatre VIS TÊTE PLATE 13 mm NOIRES (23) à travers les pattes sur les COULISSES DE TIROIR (1 et 2). Enfoncer deux PASSE-CÂBLES (11) dans les trous dans les ARRIÈRES (B et E). Séparer un TAMPON de la FICHE AVEC TAMPONS (8) et les coller sur la surface arrière du DEVANT DE PETIT TIROIR (S). Enfoncer deux PASSE-CÂBLES AVEC COUVERCLES (12) dans les trous des DESSUS (C et D).
PAGE 40
Use estas instrucciones de ensamblaje en español junto con las ﬁguras paso-a-paso provistas en el folleto inglés. Cada paso en español corresponde al mismo paso en inglés. Se destacan las ﬁguras de cada paso con una tonalidad oscura para mostrar precisamente cual parte se debe montar a la unidad. Compare la “Lista de Part” abajo con la “Part Identiﬁcation” en el folleto en inglés para familiarizarse con Las partes de ensamblaje.
PAGE 41
PASO 1 PASO 6 Ensamble la unidad sobre un piso alfombrado o sobre el cartón vacío para evitar rayar la unidad o el piso. Fije la PATA DE PARAL (G) al PARAL (F) como se muestra en el diagrama a la izquierda. Utilice dos TORNILLOS NEGROS DE CABEZA REDONDA de 51 mm (16). Empuje diez EXCÉNTRICOS ESCONDIDOS (5) dentro de los DORSOS (B y E), del PARAL (F) y del EXTREMO (H). PASO 2 Fije la PATA DE EXTREMO DERECHO (J) al EXTREMO DERECHO (H) como se muestra en el diagrama a la derecha.
PAGE 42
PASO 10 PASO 15 Fije las RIOSTRAS CORTAS (Q) a la PATA DE PARAL (G). Atornille tres TORNILLOS NEGROS DE CABEZA HEXAGONAL de 13 mm (21) utilizando la LLAVE EN L (13). Fije el DORSO DERECHO (E) al PANEL SUPERIOR DERECHO (D). Apriete tres EXCÉNTRICOS ESCONDIDOS. PASO 11 Fije el DORSO PEQUEÑO (CC) a la PARAL (F). Apriete dos EXCÉNTRICOS ESCONDIDOS. PASO 12 Fije la PATA DE EXTREMO DERECHO (J) a las RIOSTRAS CORTAS (Q) y al DORSO PEQUEÑO (CC).
PAGE 43
PASO 19 PASO 23 Fije la RIOSTRA DELANTERA IZQUIERDA (O) a la PATA IZQUIERDA (A). Atornille un TORNILLO NEGRO DE CABEZA HEXAGONAL de 13 mm (21) utilizando la LLAVE EN L (13). Fije el DORSO IZQUIERDO (B) a la PATA DE ESQUINA (EE). Utilice dos TORNILLOS NEGROS DE CABEZA REDONDA de 51 mm (16). PASO 20 Fije la PATA IZQUIERDA (A) y la RIOSTRA DELANTERA IZQUIERDA (O) al PANEL SUPERIOR IZQUIERDO (C). Utilice cinco TORNILLOS NEGROS DE CABEZA REDONDA de 40 mm (17).
PAGE 44
PASO 26 PASO 29 1. Fije los LADOS DE CAJÓN GRANDE (X y Z) al DORSO DE CAJÓN GRANDE (Y). Use cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 25 mm (19). Fije los LADOS DE CAJÓN PEQUEÑO (T y V) a las CORREDERAS DE CAJÓN (1 y 2). Pase cuatro TORNILLOS NEGROS DE CABEZA PERDIDA de 13 mm (23) a través las lengüetas de las CORREDERAS DE CAJÓN (1 y 2). 2. Deslice el FONDO DE CAJÓN GRANDE (BB) en las ranuras de los LADOS DE CAJÓN GRANDE (X y Z) y del DORSO DE CAJÓN GRANDE (Y). 3.
PAGE 45
WARNING Please use your furniture correctly and safely. Improper use can cause safety hazards, or damage to your furniture or household items. Carefully read the following chart. Look out for: What can happen: How to avoid the problem: • Overloaded shelves or drawers. • Improper loading can cause the product to be top-heavy. • Risk of injury. • Top-heavy furniture can tip over. • Overloaded shelves and drawers can break. • Never exceed the weight limits shown in the instructions.
PAGE 46
ADVERTENCIA Por favor use el mobiliario correcta y seguramente. El mal uso puede causar riesgos de seguridad o daño a las unidades o artículos domésticos. Cuidadosamente lea la tabla a continuación. Esté alerto de: Puede ocurrir: Evitar el problema: • Estantes o cajones sobrecargados. • Riesgo de lesiones. • Cargar el producto de manera inadecuada • El mobiliario inestable puede volcarse. puede causar la inestabilidad. • Estantes y cajones sobrecargados pueden romperse.
PAGE 47
5-YEAR LIMITED WARRANTY 1. provides limited warranty coverage to the original purchaser of this product for a period of ﬁve years from the date of purchase against defects in materials or workmanship of furniture components. As used in this Warranty, “defect” means imperfections in components which substantially impair the utility of the product. This Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state. 2.