Trevi GO 2000 WIFI Sport Wi-Fi HD Camera User Manual English
Thank you for purchasing this Wi-Fi camera. Before using the camera, please read this manual carefully to maximize its performance. Special notices about the waterproof case Before sealing the waterproof case, keep the camera housing’s rubber seal clean. A single hair or grain of sand can cause leaking. You can test it by closing the case without inserting the camera. Submerse the case completely in water for about one minute.
Appearance and buttons 1. 2. 3. 4. 5. 6. 7. Shutter button Built-in microphone Status LCD Lens Wi-Fi button and Wi-Fi status indicator Power / Mode button Infrared signal reception light 8. 9. 10. 11. 12. 13.
Status LCD Icons 1. Camera mode 2. Video recording mode 3. Wi-Fi icon (displayed when enabled) 4.
. Photo resolution / video size icon: (a) In camera mode, HI stands for 8 Mega Pixels, and in video recording mode, it stands for FHD (1920x1080, 30fps). (b) In camera mode, LO stands for 5 Mega Pixels, and in video recording mode, it stands for HD (1280x720, 30fps). (c) HILO only displays in video recording mode which stands for 1280x720, 60fps. 6. Mute mode: Displays when enabled. 7. Photo counter: Displays up to 999. 8. Video recording timer: Displays hours and minutes. 9.
Introduction of working modes There are four modes as in the following chart. Continuous shooting mode and self-timer mode are to be controlled by the cell phone.
Video recording mode and photo mode flow chart After the camera is turned on, you can short press the Power/Mode button to switch between modes by the following order.
Preparation 1. Insert a microSD or microSDHC card. 1. Please use memory cards with speeds faster than Class 4. 2. The camera supports memory cards up to 32GB. 3. Please make sure the memory card is inserted by correction direction. 4. Make sure the cameras is off when inserting or removing the memory card. 5. To remove the memory card, press down the memory card and the memory card will pop up.
2. Battery 2.1 Install the battery First please make sure that the camera is off when inserting or removing the battery. Step 1 Step 2 Step 1: Slide up the battery cover switch ( Step 3 Step 4 ) to open the battery cover. Step 2 & Step 3: Insert the lithium battery into the battery compartment. Make sure the contacts of the battery are corresponding to the symbols on the camera body ( ). Step 4: Place back the battery cover.
2.2 Charging the battery (a) Make sure that the camera is switched off (If the camera is being switched on, the battery will not be charged). (b) Connect the camera with the PC via the USB cable to start battery charging. The charger indicator will be lit in blue color while charging and will go off when charging is completed. Turn on/off the camera 1. Turn on the camera: Long press the button for about 3 seconds until the status LCD displays “ON” and a beep sound is heard.
2. Turn off the camera: Long press the button for about 3 seconds until the status LCD displays “OFF” and a beep sound is heard. Note: The camera will be automatically shut down to save power after the camera is being idle for 5 minutes.
Start to Use 1. Video recording mode To record a video, make sure the camera is under video recording mode which the the status LCD. If not, short press the Start recording: Press the icon is displayed on button repeatedly until the icon appears. button, the icon and the [ : ] displayed on the LCD will flash. At the same time the red indicator flashes which indicates that the recording is in process. Stop recording: Press the button, the icon and the [ : ] displayed on the LCD will stop flashing.
Note: When the microSD card is memory full or the battery is drained, the recording will stop automatically. The recorded video will be saved before the camera goes off. 2. Photo mode To take a photo, make sure the camera is under photo mode which the LCD. If not, short press the Press the icon is displayed on the status button repeatedly until the icon appears. button to take the photo. There will be a beep sound and the red indicator will flash when the photo is taken and under process.
3. Mute / activate sound The sound is enabled by default. In the video recording mode or photo mode, long press the shutter button to mute sound. The icon will be displayed on the status LCD when the sound is being muted. Long press the shutter button again will activate the sound. 4. Connecting to HD TV 4.1 Connect the camera to an HDTV via HDMI cable (not included) If you wish to playback the saved photos and videos on an HD TV, connect the HDMI cable (Mini HDMI) between the camera and the HD TV.
Note: Before connecting or removing the HDMI cable, please stop video recording and disconnect the Wi-Fi connection.
In Playback mode, short press the power /mode button are several photos or videos, press the Wi-Fi button is selected, press the shutter button to switch between photos and videos. When there to select the desired photo or video. When a video clip to start the playback and press the shutter button again to stop the playback. 4.
No. Item Description 1 Playback mode Camera is currently in Playback mode. 2 File number There are 31 files and the current file is number. 19. 3 Video icon The current file is a video clip. In Playback mode, long press the shutter button will appear. Press the Wi-Fi button power button and a prompt for file deletion and memory formatting to switch between file deleting and memory formatting. Press the to select YES or NO and press the shutter button 16 to confirm and exit.
Format 5. Connecting to PC and using PC camera feature 5.1 Turn on the camera and connect it to PC by the USB cable and the camera will enter the PCU mode. The saved photos and video clips can be found in the following folder: “My Computer Removable Disc”.
Note: When the camera is connected to your PC you will see the internal memory of the camera where it is not possible to make recordings, but that contains a file named SSID_PW.CFG that contains the configuration data for the Wi-Fi camera (SSID name and password). 5.2 Press the Shutter button press the can switch to the PC camera mode (PCC mode). To return to PCU mode, button again. Note: The PC camera mode can only be activated when your computer’s operating system is Windows XP SP3.0 / Mac 10.
Remote Control Power off button Signal emission port Video button Photo button You can use the remote controller to record videos, take photos and shut down the camera. When using the remote control, please make sure that the signal emission port on the remote control is pointing to the infrared signal reception light on the camera.
Infrared signal reception light (a) Press the video button to record a video and stop the recording. (b) Press the photo button to take a photo.
Using Wi-Fi 1. Android O/S (a) Search for “SYMAGIX APP” from “Play Store®” on your cell phone and install it. When the installation is completed, this icon will show on the cell phone’s screen . (b) Insert the microSD/microSDHC card in the camera’s memory card slot. (c) Press the Wi-Fi button on the side of the camera to active the camera Wi-Fi (When the camera Wi-Fi is getting ready, the Wi-Fi status indicator will be flashing.
(e) Click the icon and now you can control the camera by your cell phone. The introduction of the user interface is as following. 1. 2. 3. 4. 5. 6. 7. 8. 9. Video resolution White balance Setup (enter setup menu) Enter playback mode Shutter button Photo mode Video recording mode Wi-Fi signal Battery power level Note: Wi-Fi will be automatically disabled when the camera cannot be connected to the Wi-Fi network within 30 seconds.
2. iOS O/S (a) Search for “SYMAGIX APP” from “App Store®” on your cell phone and install it. When the installation is completed, this icon will show on the cell phone’s screen . (b) Insert the microSD/microSDHC card in the camera’s memory card slot. (c) Press the Wi-Fi button on the side of the camera to active the camera Wi-Fi (When the camera Wi-Fi is getting ready, the Wi-Fi status indicator will be flashing.
(e) Click the icon and now you can control the camera by your cell phone. The introduction of the user interface is as following. 1. 2. 3. 4. 5. 6. 7. 8. Battery power level Video resolution White balance Setup (enter setup menu) Enter Playback mode Shutter button Photo mode Video recording mode Note: Wi-Fi will be automatically disabled when the camera cannot be connected to the Wi-Fi network within 30 seconds.
PRECAUTIONS FOR CORRECT DISPOSAL OF THE PRODUCT The symbol shown on the equipment indicates that waste must be disposed of in “separate collection” and so the product must not be disposed of together with urban waste. The user must take the product to special “separate waste collection centres” provided by local government, or deliver it to the retailer against the purchase of a new product.
INFORMATION NOTE ON THE REMOVAL AND DISPOSAL OF BATTERIES Warning: Only high-qualified personnel should perform this operation! BATTERY REMOVAL The appliance should not be plugged to the mains socket when performing this operation! 1) Remove the battery cover as indicated in Chapter 2; 2) Select the battery; 3) Disconnect and remove the battery. Used batteries should not be disposed of with household waste or thrown into fire or water.
For additional information and updates of this product see: www.trevi.it Trevi S.p.A.