2 0 2 3 DEC KI NG INSTA LLATION GU I DE
INSTALLATION GUIDE Trex Installation Guide CONTENTS To learn about Trex Signature®, Transcend® and Select® railing products, visit www.trex.com/products/railing What’s New for 2023: Page 10 – Added new product information Page 31 – Updated color palette Need Help? Trex provides a variety of valuable resources to answer your questions or concerns. For additional assistance, check out: » Trex.
Trex decking and railing are heavier and more flexible than wood. DO NOT try to lift the same quantity of Trex boards as you would traditional lumber. Go to www.trex.com for Safety Data Sheets (SDS). When working on any construction project, you should wear protective clothing and safety equipment. Wear safety glasses, gloves, a dust mask and long sleeves, particularly when cutting in confined spaces.
GENERAL INFORMATION 4 TREX TRANSCEND®, TREX ENHANCE® AND TREX SELECT®DECKING Care and Cleaning Guide All exterior building materials require cleaning. Generally, soap and water is all that is required to clean Transcend, Enhance, and Select products. For additional information, see below. Refer to Trex.com for cleaning recommendations for early generation decking products. Problem Solution Dirt and Debris The affected area should be sprayed off with a hose to remove surface debris.
Problem Solution While this is not common, static electricity can occur on walking surfaces in dry climates or in areas where dry winds and dust-borne particles lay on the decking surfaces. Static electricity can build up on occupants walking across any composite decking surface, including Trex, then produce a small static shock if they touch a grounded metal surface such as railing, door, etc.
PLANNING AHEAD PLANNING AHEAD 6
PLANNING AHEAD Trex Decking: Trex Decking Temperature: Like many other outdoor surfaces, such as concrete, asphalt, beach sand, wood decking, other brands of composite decking, etc., Trex decking can get hot due to weather and sun exposure. On such days, care needs to be taken to make sure skin does not have extended contact with the surface of the deck, especially with young children and those with special needs. Please note also that the darker the color, the hotter the deck will feel.
PLANNING AHEAD/CONTINUED Installing Hot Tubs, Planters, and Seating: » You need to consider the location of your pergola posts with respect to joists. However, you do not have to mount your plates between joists. It is possible to place blocks on the bottom of the joists and mount the Trex Pergola brackets through the blocks. » Plan ahead proper joist spanning if required (this is especially important if installing a hot tub). » Refer to page 16 for Trex Decking Span Chart for specific loads.
DECKING DECKING 9
TREX® DECKING & FASCIA P R O F ILE D ES C RI PT I ON 1" Square-Edge Board Actual dimensions: Transcend & Enhance: .94 in x 5.5 in x 12 ft / 16 ft / 20 ft (24 mm x 140 mm x 365 cm / 487 cm / 609 cm) Select: .82 in x 5.5 in x 12 ft / 16 ft / 20 ft (20 mm x 140 mm x 365 cm / 487 cm / 609 cm) 1" Grooved-Edge Board Actual dimensions: Transcend & Enhance: .94 in x 5.5 in x 12 ft / 16 ft / 20 ft (24 mm x 140 mm x 365 cm / 487 cm / 609 cm) Select: .82 in x 5.
Decking and Fascia Recommended Fasteners If any condition occurs which is attributable to the use of non-recommended fasteners, such condition shall not be covered under the Trex Limited Warranty.
Trex® Fascia Installation Recommendations General Notes: » Trex Fascia utilized around the perimeter of a deck must be gapped with the same requirements as Trex decking to allow for expansion/contraction of the fascia » When using 2" x 8" framing, attach fascia using 2 fascia approved fasteners; when using 2" x 10" or larger framing, attach fascia using 3 fascia approved fasteners.
Trex® Fascia Installation Recommendations WHEN USING DECK BOARDS AND COMPOSITE DECKING FASTENERS FOR FASCIA. While Trex prefers the previous methods of attachment for fascia applications, as these are the very best options, there are also other recommendations that can be followed for deck boards being used for fascia. Use two Trex recommended composite decking screws every 12". NOTE THAT FASCIA APPROVED FASTENERS CANNOT BE USED IN THIS APPLICATION.
NOTE: When using pneumatic or battery-operated equipment, adjust the pressure so that you only shoot the head of the screw to be flush with the board’s cap. DO NOT shoot the fastener head completely through the shell. Clean Cut Boards In most cases, install fasteners at a 90° angle (perpendicular to the board).
Rooftop and Sleeper Deck Systems – Pressure-Treated Framing A sleeper system is a substructure between a solid surface and Trex decking. Drainage, access, and airflow are critical. Water must be able to flow through and away from the deck. For repairs and removal of debris, joist system access may be necessary. NOTE: English measurements are shown. Convert to metric measurements if necessary. 3/16" (All Temps) 1/8" (>40°F) 3/16" (<40°F) 1/4" (>40°F) 1/2" (<40°F) 1/2" Max. Overhang Min.
Metal Framing Requirements and Gapping NOTE: Metric measurements are shown. Convert to US measurements if necessary. Two screws per joist Gap decking width-to-width 5mm (All Temps) Gap decking end-to-end 3mm (>4°C) 5mm (<4°C) Double joist spacing per manufacturers requiremenrs requirements DECKING 13mm max.
Code Compliance Joist Spanning for Decking Adjust Joist Spanning to Accommodate Angled Decking Patterns Trex decking meets all applicable national model building codes. The joists must be spaced on center according to the chart below. Be sure that joists are level and plumb. Trex decking must span at least three joists. For heavy items such as hot tubs, planters, etc., consult a local building engineer or inspector for span recommendations.
Gapping and Overhang You must gap Trex decking both end-to-end and width-to-width. Gapping is necessary for drainage and the slight thermal expansion and contraction of Trex decking boards. Gapping also allows for shrinkage of the wood joist system. » ALWAYS follow Trex-recommended gapping guidelines. » Maximum allowable perpendicular overhang for all Trex decking is 3/4" (19 mm). » All decks require air circulation to keep them dry and looking good.
Important Notes Before Installing Trex® Decking It is recommended to clean cut boards on both ends a minimum 3/16" (5mm). To ensure an appealing mix of color tones, mix and match all boards prior to installation.
TREX HIDEAWAY® One-Step Hidden Fastener Tool Instructions The Hideaway® One-Step Installation Tool increases installation speed by allowing you to install the fastener in one easy step. With this tool you can fully actuate the fastener and still install your next deck board, converting what’s normally a two-step process into a one-step installation process.
TREX HIDEAWAY® One-Step Hidden Fastener Tool Instructions/CONTINUED NOTE: See instructions included with Trex Hideaway Universal Hidden Fasteners for general rules including clean cutting board ends, gapping rules, abutted board rules and installation of angled deck boards, as well as start clip instructions, steps to take for large temperature shifts and installation of last deck board. Installation Instructions 1 3 1 2 1 2 1. Place Hideaway hidden fastener into one-step tool.
Installing Trex Transcend®, Enhance®, Select® Decking NOTE: These instructions should be followed when NOT using the One-Step Tool. 1 2 1 1 1/4" >40°F* 1/2" <40°F* 2 *6mm >4˚C 13mm <4˚C 3 4 1 1 HOW TO INSTALL DECKING 3 2 2 NOTE: Use scrap piece of decking to help hold fastener in place while attaching.
Installing Trex Transcend®, Enhance®, Select® Decking/continued Installing Last Deck Board (Square-Edge Board Recommended) 9 10 1 2 1" (25mm) Route one side of square-edge board to use with hidden fasteners. TIP: Use a recommended hidden fastener screw and plug for last board installation. Fascia screws supplied by installer (1" x 8" fascia shown) NOTE: Refer to page 12 for detailed fascia attachment instructions.
Spanning Requirements for Trex® Stairs Note: English measurements are shown. Convert to metric measurements if necessary. 11" min. depth Stringer 1/4" - 3/8" gapping 3/4" max. overhang Fasten treads to all stringers 1” x 8" Riser HOW TO INSTALL DECKING Riser removed for clarity 36" minimum width – 4 stringers are required Above 36" width – 5 stringers are required Stairs Stairway Detail » Stair treads built with Trex meet requirements of the major national building codes.
Installing Trex® Stair Treads Installed with Hidden Fasteners NOTE: If using hidden fasteners, use square-edge, composite decking boards and manually route these on required sides to allow for use with hidden fasteners. In addition, if not using hidden fasteners, square-edge boards can all be used and face fastened using Trex recommended fasteners. 2 1 1 1 1 1 1/4" >40°F* 1/2" <40°F* 2 *6mm >4˚C 3mm <4˚C 4 3 2 1 5 6 HOW TO INSTALL DECKING 1 Rout one side of board (last stair tread).
WARRANTIES 26 WARRANTIES
WARRANTIES TREX ® D ECKIN G & FAS C IA LIM ITED WA RRAN T Y Trex Company, Inc.
WARRANTIES TR EX ® DEC K ING & FAS C I A LIM ITED WAR R AN T Y (continued) 3. Upon confirmation by an authorized Trex representative of a valid claim hereunder, Trex’s sole responsibility shall be, at its option, to either: (a) replace the affected Product with new Product in an amount equal to the volume (linear feet) of defective material; or (b) refund the portion of the purchase price paid by Purchaser for such affected Product (not including the cost of its initial installation).
WARRANTIES TREX ® FAST E N E RS LIMIT E D WARRAN T Y Trex Company, Inc.
TR EX® FASTENERS LIMIT E D WARRAN T Y (continued) Year of Claim Warranty Period 50 Year 35 Year 25 Year 38 20% – – 39 20% – – 40 20% – – 41 20% – – 42 20% – – 43 10% – – 44 10% – – 45 10% – – 46 10% – – 47 10% – – 48 10% – – 49 10% – – 50 10% – – THE LIMITED WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY TREX IN CONNECTION WITH THESE PRODUCTS.
DECKING COLOR PALETTE Rainier Transcend® Lineage™ Carmel Transcend® Lineage™ Biscayne Transcend® Lineage™ Jasper Transcend® Lineage™ Gravel Path Transcend® Earth Tones Island Mist Transcend® Tropicals Rope Swing Transcend® Earth Tones Tiki Torch Transcend® Tropicals Havana Gold Transcend® Tropicals Spiced Rum Transcend® Tropicals Vintage Lantern Transcend® Earth Tones Lava Rock Transcend® Tropicals Pebble Grey Select® Foggy Wharf Enhance® Naturals Winchester Grey Select® Rocky Harbor Enhance
front: Transcend Lineage in Biscayne with Signature Glass and Aluminium Railing back: Transcend Tropicals in Island Mist with Transcend Railing FIND US ON Visit trex.com or call 1-800-BUY-TREX DECKING | RAILING | LIGHTING | S P I R A L STA I R S 0123 | CORNHOLE | FASCIA | KITCHENS | FURNITURE | PERGOLA | DRAINAGE L AT T I C E | CLADDING | HIDDEN FASTENERS | FENCING ©2023 Trex Company, Inc. All rights reserved.
