TRIAX SR 110 Digital satellite receiver 350008 User Guide
Contents Introduction........................................................................................................................................5 Nice to know ................................................................................................................................5 Typographical Conventions .........................................................................................................6 Safety Instructions .........................................................
M/P (Multipicture) .....................................................................................................................30 MUTE ........................................................................................................................................30 FAV............................................................................................................................................30 RECALL ............................................................................
Introduction This user guide intends to provide you with knowledge of how your new digital satellite receiver (called a receiver for short) functions. We assume that you have a general knowledge of how to handle electrical and electronic consumer equipment such as television, radio, video cassette recorder and DVD-player.
• Polish • Slovakian • Swedish • Slovenian • Finnish Ex works the following satellites are pre-programmed: • Astra1 19E • Hotbird 13E • Türksat 42E • Sirius2 5E • Amos/Atlantic 4-5W • Astra2 28E • HispaSat 30W • Eutel W2 16E • HellaSat 39E • Astra 23,5E Typographical Conventions In the following you can read about the typographical conventions used in the user guide.
Safety Instructions Always follow the safety instructions below to avoid the risk of injury to yourself or damage to your equipment. • In order to ensure adequate air circulation, place the receiver on a smooth, flat surface, and do not place any articles on the top of the receiver. Ventilation slots designed to assist circulation and to allow heat to dissipate from the receiver are located here. • Do not place the receiver on an unstable cart, stand, tripod, bracket, or table.
Batteries For the remote control you need two batteries of the micro type: AAA/1.5 V. In connection with the batteries please pay attention to the information below • Observe the prescribed polarity when you put batteries into the battery compartment. • Always change both batteries at the same time and use batteries of the same type. • Change batteries that are becoming weak in good time. • Leaking batteries can cause damage to the remote control.
Device Overview: SR 110 Front Panel Rear Panel 9
Remote Control 10
Remote Control Button Description No.
Package Supplied Check the package supplied after purchase: No. Quantity Explanation 1 1 Receiver 2 1 Remote control 3 2 Batteries type AAA/1,5 V - 1 Operating manual (not shown) Note that: • The coaxial and SCART cables are not included in the package supplied.
Connecting the Receiver Do not connect the receiver to the mains power supply until you have connected it properly to all devices and to the aerial. Otherwise the receiver may be damaged. The wire mesh and the inner wire of the coaxial cable carry electrical current during operation. Fitting the Aerial Cable The receiver is connected to your satellite aerial via a coaxial cable and the F-connector. For fitting the F-connector onto the coaxial cable you need wire strippers and wire-cutting pliers.
Turn the F-connector onto the peeled-back wire mesh, until the connector comes up against the inner insulation. There must be no wire mesh overlapping at the back of the connector end. Shorten the inner core with wire-cutting pliers, so that it protrudes a maximum of 1 mm out of the connector. Screw the F-connector of the coaxial cable onto the “LNB IN” aerial connection on the receiver. The other end of the coaxial cable should be firmly screwed onto the LNB.
Stereo system - analogue If you wish to connect a stereo system, connect the cinch connector of the cinch cable with the “AUDIO R” and “AUDIO L” sockets of the receiver. Follow the operating instructions of the stereo system. Never connect the phono input of your stereo system with the receiver, which can destroy your stereo system.
Connecting and Aligning the Aerial In principle we recommend you have the assembly and commissioning of your aerial installation carried out by qualified specialised staff. Should you do the installation yourself, please adhere to the assembly instructions for your satellite aerial and the following instructions. Please connect the aerial cable to the receiver first, then after this connect the receiver to the power supply. Before you align the aerial, you must connect the aerial cable to the LNB.
Example: If you want to receive the Astra 19.2° East satellite, you must put your receiver onto channel 1 to align the aerial. The same also applies for other satellites such as Hotbird. If you wish to align your aerial to Hotbird, you must call up a pre-programmed Hotbird channel on your receiver. Step 3 Now align your aerial with the satellite you have selected. There are several possibilities for doing this.
Start-Up Remote Control For the remote control you need two batteries of the micro type: AAA/1.5 V. • Observing the prescribed polarity, put two batteries into the battery compartment and close the battery compartment cover again carefully until the cover locks in position. • Change batteries that are becoming weak in good time. Always change both batteries at the same time and use batteries of the same type • Leaking batteries can cause damage to the remote control.
Information bar During a channel change, an information bar is displayed on the screen for 5 seconds (can be altered via the menu System Settings – OSD Setting – OSD Delay).
The Receiver Menus User Interface on the TV screen You can adjust the individual settings of your receiver via the menus of the user interface. Switch on the receiver and the TV set. Press the MENU key on your remote control to display the main menu Press the EXIT key to leave this menu, or press the MENU key again.
Navigating through the Menus You can navigate through the menus using the CH+/▲ and CH-/▼, V+ and V-. The chosen menu items will be marked. Selection is via the OK key on the remote control. Some of your changes may have to be confirmed via the OK key. You can leave the menus using the EXIT key. In every menu, you will find an area at the bottom which will show you the selection options assigned to the various buttons on the remote control.
(Symbol: Receiver) TV System See following text Channel Setup See following text Time & Timer Setting See following text OSD Setting See following text Parental Lock See following text LNB Power See following text Tools Factory Reset See following text (Symbol: Toolbox) Software Update See following text Game See following text Information See following text Channel (Symbol: TV set) Submenu Description TV Channel List 1 Favourite, 2 Move, 3 Find, 4 Sort, 5 Edit, 6 Type, CH+/▲ CH-
Favourite Having selected a channel you determine your favourite by pressing the 1 key. Next to the relevant channels, a heart symbol will appear. Move When the 2 key is pressed, the move symbol appears behind the selected channel. Using the CH▲ CH▼ keys, the channel is moved to the required location. The action must be confirmed with OK. Find Channel search function. Channels can be found selectively by entering alphabetic characters on the OSD keyboard.
Skip Using the 2 key, selected channels can be marked for skipping. Selected channels will then be jumped during zapping (channel hopping). Please confirm the selection using the OK key. You can still see the channel if you press the channel number. Lock Using the 3 key, selected channels can be marked for locking. Please confirm the selection using the OK key. Access to marked channels will then require a password (protection of children). Create You can get into edit mode via the 4 key.
Submenu Description Antenna Setup Satellite Satellite selection (e.g. Astra1° East). LNB type Select LNB type (Standard setting is ”Universal”). 22K Activating 22KHz (Note: With LNB type ”Universal” the activation is automatic) DiSEqC Select DiSEqC level DiSEqC Switch Select DiSEqC command Example: Astra og Hotbird double reception Astra = 1/4 Hotbird 2/4 Positioner You can access the DiSEqC motor control menu via the OK key. Please consult the operating guide of your DiSEqC motor.
System Setup (Symbol: Receiver) Submenu Description Audio Language First audio Pre-selection of audio language (if offered by channel). Second audio Pre-selection of audio language (if offered by channel). Display mode Selection of transmission system. Standard selection: PAL Aspect mode Selection of image format. Standard selection: 4:3 (Letterbox) Video Output Only the video signal CVBS is offered.
setting Parental Lock LNB Power Factory password is: 0000 Installation Lock Switching password input on/off in the main menu item Installation. Channel Lock Switching password input on/off for locked channels (child protection). New password Determining a new password (new password must be remembered). Gonfirm password Confirm new password. Switching LNB power supply on and off. Preset is ”On”. Timer Submenu Description Timer number Selection of timer number 1-8.
Tools (Symbol: Toolbox) Submenu Description Factory Reset Reset receiver to factory settings. All changes are reset. Note! If you press the standby key on the front of your receiver for more than 10 seconds, the factory settings will also be reinstated. Caution!! Doing so will delete your personal settings. (password input required) Software Update You can download new operating software in the event of a service requirement. The upgrade function via satellite is not active, but prepared.
Special Function Keys TV/SAT Using this key, you can switch between TV function and satellite function. (This function must be available on your TV set, however). Press the TV/SAT key repeatedly, until the desired function is achieved. TV/RADIO With this key you can switch between TV function and DVB radio function. The receiver is now transmitting a radio channel and displaying a background image. Press the TV/RADIO key repeatedly, until the desired function is achieved.
On the right-hand side, the current and following event is indicated. Press the 1 key to display the complete events list. Using the V- V+ keys, you can scroll through the days, and using the CH+/▲ CH-/▼ keys, you can scroll back and forth through the events. Press the 1 key to obtain detailed information for a selected event. Using the 2 key, you can transfer this directly into the timer. TEXT In order to receive Teletext, the selected channel must support this function.
RECALL This key takes you back to the previously chosen channel. Press the RECALL key to return to the previously chosen channel. INFO – Acoustic signal for aligning the satellite aerial This key is used for aligning the satellite aerial via an acoustic signal. Besides the current reception parameters, you will also be shown signal strength and signal quality. In addition, you can activate an acoustic signal using the 1 key that will be output via the TV set.
Disassembly and Cleaning Disassembly • Separate the receiver and the connected units from the power supply. • Unscrew the LBN cable from the receiver. • Remove the batteries from the remote control unit if you are not going to use the receiver for quite some time. • Pack the receiver, the cables and the remote control unit in the carton. • Store the receiver and all accessories in a dry and dust-free place. • Protect the receiver against frost. Cleaning The receiver must not get wet.
Troubleshooting Symptom? Cause? Remedy Can’t find satellite, or no signal. Example: ASTRA19° East Key 1 (pre-programming: ”Das Erste”). INFO key(”Das Erste”, FR11837). Both signal and quality are 0 %. Align vertical mirror to the south. Turn a few millimetres to the left, wait about 3 seconds, then repeat until both signal and quality are shown. With a signal of about 60%, the black background will disappear, and a TV image will appear.
The LNB is defective. Replace the LNB. No picture, no sound, signal strength present, no signal quality. The satellite aerial is aligned with the wrong satellite. Bad reception of: Tele5, DSF, etc. Cordless phone causing interference (DECT standard) Move the cordless phone, use better quality satellite cable. The remote control unit does not work. Batteries discharged. Replace batteries. The remote control unit is aligned wrongly.
Technical Data Receiver Input frequency range 950 MHz ~ 2150 MHz LNB power supply 13/18 V, 0.30 A max. Overload protection IF Band width 55 MHz/8MHz (below 5MS/s) LNB control 22 KHz +/- 2KHz, 0,6 V pp +/- 0,2 V DiSEqC control Version 1.0, version 1.2, Tone-Burst A/B Symbol rate 1 ~ 35 MS/s Bit rate 115200 Bit/s Input speed Max.
Manufacturer Dear Customer, Should you require technical assistance and in the event that your expert dealer was unable to help you, please contact us.
Glossary AC Alternating Current. Connection for AC. DC Direct Current. Connection for DC. Cinch connector Coaxial connector for the connection of TV set or stereo system. DiSEqC Digital Satellite Equipment Control Digital system with which the receiver can control various components of the outer unit. It is employed particularly to choose between several satellite positions. DVB Digital Video Broadcasting. Broadcasting of digital TV programmes.
www.triax.
