SR-26 User Guide SR-26 ANALOG SATELLIT RECEIVER • • • • • • • • • • • • • • • • • • 450 Pre-programmed channels (ASTRA, EUTELSAT/HOT BIRD, and other) 2 SCART connectors (TV and VCR/DECODER) OSD On-Screen-Display (English and German) Parental lock and favourites list Frequency range 920 – 2150 MHz LNB control via 14/18 volt, 22 kHz and DiSEqC 1.
CONTENTS GENERAL PROPERTIES ........................................................................................... 2 SAFETY PRECAUTIONS ............................................................................................ 3 Power Source: ................................................................................................... 3 Power Cord: ...................................................................................................... 3 Choice Of Location: .......................
GENERAL PROPERTIES 1) User-friendly OSD menu control (2 languages) 2) DiSEqC 1.
SAFETY PRECAUTIONS Power Source: The receiver should be operated only from an 85-265 V AC, 50 Hz outlet. Please do not open the cover by yourself. There is high voltage in the set, which will danger your life. Please ask closest service for help. Power Cord: The power supply cord should be placed so that they are not likely to be walked on or pinched by items placed upon them or against them.
SATELLITE ANTENNA To have an excellent function of the sat-receiver, it is necessary to install the antenna correctly. Please avoid under all conditions to have a short circuit at the antenna cable conductor (LNB receiver). The sat-receiver is equipped with a LNB short-circuit protection. PUTTING ON THE BATTERIES OF THE REMOTE CONTROL First open the battery cover on the underside of the remote control. Put on both batteries 1.
Tuning your TV to the Sat-receiver: Put the switch Test/TV on the backside of the set to position TEST. The signal of the sat-receiver is tuned for channel 38(UHF) ex factory. Turn on your TV and tune it with the channel search (UHF area) to the test signal. The test signal exists of two vertical white stripes on black background. Memorize this tuning on an unused program on your TV. You can later receive the satellite on this program. If needed, please use the operation manual of your color TV.
FUNCTIONS ON THE FRONT PANEL OF THE RECEIVER 1. STANDBY : If the receiver is in the standby position, you can turn on or off with this button. (last tuned program will be shown). 2. BUTTONS : Modification on selected pages aremade by these buttons. These buttons can also be used to exit standby. 3. LED DISPLAY : The 4 digit LED display is for displaying the program numbers.
CONNECTIONS AND SERVICE ELEMENTS AT THE BACK SIDE OF THE SET 79 287 $8',2 79 7(67 '(&2'(5 9&5 /()7 $& 9 +] 5,*+7 $17 ,1 4. LNB Input Connection to outside unit (LNB). Use F connector. 5. Test signal switch The test signal can be switched with Tuning of RF output channel between Ch 30-Ch 39 6. 7. ANT IN Input for terrestrial TV antenna 8. TV OUT Antenna connector to the TV. 9. TV SCART Audio and Video connection socket to the TV. 10. DECODER-VCR Connection for Decoder or Video.
REMOTE CONTROL FUNCTIONS 13. STANDBY : The receiver can be turned on or off with this button. 14. (MUTE) : For the interruption of the sat-receiver sound (Mute). 15. 0-9 BUTTONS : For the direct selection of the program number, video and audio frequency. 0 key also has an AV function. 16. - : Decrease the volume or change the positions among the program number, name, frequency of LNB, video and audio. 17. MENU : To enter the top menu. 18. This button has no function. 19.
MENU INTERFACE Menu System: When the MENU key is pressed on R/C, the main menu is entered. This menu page consists of four sub-menus. These are as following; P+, P- are used to move up & down in the main menu as the other pages. + or - is used to enter the sub-menus in the main menu. Exiting from this menu is only made by the TV, Store and Standby buttons. TV to exit to program page without saving. Store to save settings in all of the sub-menus and return the program mode.
In LNB NO line, 8 or 16 different LNB configurations (corresponding to the LNB NO line in the installation page) can be chosen by using +,- (8 for DiSEqC OFF, 16 for DiSEqC ON mode). At every LNB NO changing, the video frequency is driven according to selected LNB frequency. User can switch to second customizing page by pressing P+ in this line. In PR. FREQ. line, the program frequency can be entered in two different ways: i) Direct access.
To skip a program, PR. SKIP line is used. If it is enabled, the user can not reach this program with P+, P- buttons. Only direct accessing is enabled to watch the skipped program. TV is used to return without saving, Store button to return to the program mode with saving for selected channel number. To store the customizing page, Store button is pressed and then program number begins to flash. +,- or 0-9 buttons are used to change channel number.
Language: On screen menus are in 2 languages. Language is selected with + or - and stored with Store button. Setup Menu: This menu can only be entered by pressing the P+ & P- buttons in front panel of the receiver together in the standby mode. The settings of your sat receiver according to the application can be made in this menu. Factory setting of this menu will be as below. Please do not make any changes in this menu without the help of your system installer.
In the DiSEqC line, DiSEqC mode can be changed to OFF/ON. While DiSEqC is switched to OFF, REPEAT automatically changes to 0, no DiSEqC signals are generated and the installation menu is as in installation page description. The user can not reach REPEAT line in this mode. If any DiSEqC device will be used (e.g. DiSEqC 1.0 or 2.0 switch, multiswitch or LNB), DiSEqC mode must be selected as ON to communicate with these devices.
In LNB POWER line, LNB power can be switched to OFF in SMATV applications that your receiver does not need to send any signals (e.g. 22kHz, Toneburst, DiSEqC) to receive the satellite broadcasting. Otherwise, LNB POWER must be ON. In setup menu, after all the settings are finished Store button is used to save the settings and exit. If TV or Standby button is pressed, user will exit this menu without saving.
CONNECTION OF THE SAT-RECEIVER WITH A SCART CABLE - 15 -
CONNECTION OF THE SAT-RECEIVER WITH RF ANTENNA CABLE - 16 -
TROUBLE SHOOTING - 17 -
TECHNICAL SPECIFICATIONS GENERAL LNB input .................................................. : 1 Supply Voltage .......................................... : 85-265 V AC, 50Hz Program Place ......................................... : 450 channels Input Frequency ........................................ : 920-2150 MHz Carton Size (mm) ..................................... : 300x65x150 Weight ....................................................... : 1 kg VIDEO Signal .........................................
RF MODULATOR UHF output conn. ...................................... : IEC male ANT input conn. ........................................ : IEC female Standard ................................................... : PAL G Output channel ......................................... : Channel 30-39 UHF (Channel 38preprogrammed) SR REMOTE CONTROL Range ....................................................... : approx. 6m Batteries ................................................... : 2x1.
SR-26 User Guide - 20 -
SR-26 User Guide Triax A/S Bjørnkærvej 3 DK-8783 Hornsyld www.triax.