INSTRUCTION BOOKLET GB ELECTRIC HOB TBE 635 Please read this instruction booklet before using the appliance
Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 950950 Installation ● ● ● ● This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. Remove all packaging before using the hob. Ensure that the electrical supply complies with the type stated on the rating plate, located on the bottom of the hob.
Contents For the User For the Installer Important Safety Information 2 Instruction for the installer 8 Description of the Hob 3 Installation 9 Operation 4 Building In 9 Maintenance and Cleaning 5 Electrical connections 10 Something Not Working? 6 Wiring diagram 11 Service and Spare Parts 6 Customer Care Department 7 Guarantee Conditions 7 Description of the Hob 3 4 2 1 5 6 7 1. Hob Top 2. Normal Hotplate - 1500 W - 180 mm dia. 3. Normal Hotplate - 1000 W - 145 mm dia. 4.
Operation Electric Hotplates To switch on a hotplate, turn the relevant control knob anticlockwise to the required heat setting. The control knob is numbered 1 - 6 0 - OFF 1 - Minimum 6 - Maximum. The hob has two types of hotplates: Normal Hotplates We recommend the plates are switched to maximum (6) for a short while to boost the plate, and then adjusted to the required setting. Rapid Hotplates The rapid hotplates are indicated by a red dot, and will heat up more quickly than a normal plate.
Take care never to lean or reach over a hot electric plate. Always point pan handles inward or over the work surface next to the hob to avoid accidentally knocking over a pan as you pass by. Take care when frying food in hot oil or fat, as the overheated splashes could easily ignite. If the control knobs become difficult to turn, please contact your local Tricity Bendix Service Centre.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. IMPORTANT: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or installation, a charge will be made even if the appliance is under guarantee. SYMPTOM SOLUTION ■ The plate does not heat up.
Customer Care Department For general enquiries concerning your appliance, contact our Customer Care Department by letter or telephone as follows: Major Appliances Customer Care Tricity Bendix Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel: 08705-950950* * calls to this number may be recorded for training purposes Guarantee Conditions Tricity Bendix Standard Guarantee Conditions We, Tricity Bendix, undertake that if, within 12 months of the date of the purchase, this Tricity Bendix appliance
Instructions for the Installer Engineers technical data Heating elements Ratings Normal front left Hotplate Normal back left Hotplate Rapid front right Hotplate Rapid back right Hotplate Total rating Ø 180 mm Ø 145 mm Ø 145 mm Ø 180 mm Cut out dimensions 1500 W 1000 W 1500 W 2000 W 6000 W Supply connections Electric: 230V 50Hz AC electrical supply. Width: Depth: 550 mm. 470 mm. Overall dimensions Width: Depth: 580 mm. 500 mm.
Installation The hob must be installed according to the instructions supplied. The hob must be installed by qualified personnel to the relevant British Standards. Please, ensure that, once the hob is installed, it is easily accessible for the engineer in the event of a breakdown. Cut Out Size When the hob is first installed Once the hob has been installed, it is important to remove any protective materials, which were put on in the factory.
Building over a kitchen unit with door 20 min Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be hot when in operation. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections.
The hob should be connected to a double pole switch with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch should be sited within 2m of the hob and be easily accessible upon completion of the installation. The switch must not break the yellow and green earth cable at any point. Ensure that the hob supply cord does not come into contact with surfaces with temperatures higher than 50 deg. C.
Grafiche MDM - Forlì Major Appliances Customer Care Tricity Bendix Major Appliances Addington Way Luton Bedfordshire LU4 9QQ Tel: 08705-950950* * calls to this number may be recorded for training purposes From the Electrolux Group. The world’s No.1 choice. The Electrolux Group is the world’s largest producer of powered appliances for kitchen, cleaning and outdoor use.
